Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER (for LHD) › from 2021.08
RM37H0E _54 Brake _096747 BRAKE SYSTEM (OTHER) _0454025 BRAKE BOOSTER(for LHD) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER(for LHD)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C452648N01
6.292,0.667 6.792,0.667 false 6.333,0.26 6.833,0.26 false 4.063,0.833 4.563,0.833 false 5.833,0.135 6.667,0.469 0.833,0.333 18 false 1, 2 6.115,0.542 6.531,0.875 0.417,0.333 18 false 3 4.615,0.708 5.031,1.042 0.417,0.333 18 false 4

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 ACCUMULATOR PRESSURE ZERO DOWN - (Click here) - -
3 DRAIN BRAKE FLUID - - (Click here) -
4 BRAKE ACTUATOR WITH BRACKET - - - -

C451686N01
4.583,4.083 4.583,4.417 4.583,4.417 4.833,4.417 false 6.333,3 6.333,2.5 6.333,2.5 6.583,2.5 false 2.333,2 2.333,1.5 2.333,1.5 2.583,1.5 false 0.5,2.25 0.5,1.417 0.5,1.417 0.667,1.417 false 2.844,2.771 3.177,3.021 0.333,0.25 10 false x 2 6.688,3.375 7.021,3.625 0.333,0.25 10 false x 2 4.885,4.292 5.135,4.625 0.25,0.333 18 false 5 6.635,2.375 6.885,2.708 0.25,0.333 18 false 6 2.635,1.375 2.885,1.708 0.25,0.333 18 false 7 0.719,1.292 0.969,1.625 0.25,0.333 18 false 8

Procedure Part Name Code
Z101186

Z101188

Z101187

5 LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY 73900 - - -
6 AIR DUCT SUB-ASSEMBLY - - - -
7 NO. 2 HEATER TO REGISTER DUCT 55844 - - -
8 NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY 55308B - - -

C451669N01
6.094,3.917 6.427,3.917 false 5.354,1.5 5.688,1.5 false 6.667,3.167 6.833,3.167 6.833,3.167 6.833,2.667 false 2.323,0.781 2.156,0.781 2.156,0.781 2.156,1.229 false 1.167,1.615 1.333,1.615 1.333,1.615 1.333,2.281 false 4.833,2.333 4.833,2.167 4.833,2.167 5.083,2.167 false 5.917,2.083 5.917,1.917 5.917,1.917 6.167,1.917 false 4.417,2.417 4.583,3.417 4.583,3.417 4.917,3.417 false 4.635,2.927 4.74,3.406 false 4.25,3.083 4.25,3.667 4.25,3.667 4.5,3.667 false 3.417,2.531 3.417,2.115 3.417,2.115 3.583,2.115 false 5.917,3.792 6.167,4.125 0.25,0.333 18 false 9 5.74,1.375 6.073,1.708 0.333,0.333 18 false 10 6.385,3.042 6.802,3.375 0.417,0.333 18 false 11 2.615,0.677 3.031,1.01 0.417,0.333 18 false 12 0.833,1.479 1.25,1.813 0.417,0.333 18 false 13 5.281,2.052 5.698,2.385 0.417,0.333 18 false 14 6.229,1.854 6.479,2.104 0.25,0.25 10 false ● 5.146,2.094 5.396,2.344 0.25,0.25 10 false ● 5.375,2.719 5.708,2.969 0.333,0.25 10 false x 4 4.969,3.292 5.385,3.625 0.417,0.333 18 false 15 4.552,3.542 4.969,3.875 0.417,0.333 18 false 16 3.646,2.052 3.896,2.302 0.25,0.25 10 false ● 3.781,1.99 4.198,2.323 0.417,0.333 18 false 17

Procedure Part Name Code
Z101186

Z101188

Z101187

9 BRAKE PEDAL RETURN SPRING 47101A - - -
10 STOP LIGHT SWITCH ASSEMBLY 84340 - - -
11 PUSH ROD PIN 47264A - - -
12 FRONT COMPARTMENT MAIN WIRE 82111C (Click here) - -
13 BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY 47210L (Click here) - -
14 BRAKE MASTER CYLINDER GASKET 44785D - - -
15 BOOSTER BRACKET STOPPER RING - - - -
16 BRAKE BOOSTER BRACKET - - - -
17 BRAKE MASTER CYLINDER GASKET 44785D - - -

● Non-reusable part - -

C451672N01
5,0.5 5.25,0.5 false 1.417,2.969 1.833,2.969 false 2.979,3.417 3.313,3.417 false 1.115,2.865 1.531,3.24 0.417,0.375 18 false 18 2.646,3.302 3.063,3.677 0.417,0.375 18 false 19 5.635,0.375 6.052,0.75 0.417,0.375 18 false 20

Procedure Part Name Code
Z101186

Z101188

Z101187

18 NO. 1 RESERVOIR HOSE - (Click here) - -
19 NO. 2 RESERVOIR HOSE - (Click here) - -
20 NO. 1 WIRE CLAMP BRACKET - (Click here) - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during brake booster with master cylinder assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
No. 1 Skid control ECU (brake booster with master cylinder assembly) Update ECU security key Vehicle control history (RoB) are stored (Click here)
1.

Bleed air

2.

Perform "Calibration"


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator) illuminates

·

Slip indicator light illuminates

·

Electronically controlled brake system disabled or malfunctions


(Click here)

CAUTION:
·
A340386

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

·
A340358

To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.



HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Air conditioning system After the ignition switch is turned to ON, theservo motor and expansion valve standardposition is recognized. -



CAUTION / NOTICE / HINT

NOTICE:
·

While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.

·
C453035C01
0.688,0.5 0.938,0.5 false 0.75,1 1,1 false 0.833,1.5 1.083,1.5 false 1.031,1.833 1.281,1.833 false 2.667,1.833 2.917,1.833 false 2.292,1.5 2.458,1.417 2.458,1.417 2.625,1.417 false 2.375,0.667 2.625,0.667 false 1.719,0.99 1.885,0.406 1.885,0.406 2.052,0.406 true 2.677,0.604 3.01,0.854 0.333,0.25 10 false *a 0.573,0.938 0.906,1.188 0.333,0.25 10 false *b 2.969,1.771 3.219,2.021 0.25,0.25 10 false *c 2.677,1.354 2.927,1.604 0.25,0.25 10 false *d 0.51,0.438 0.844,0.604 0.333,0.167 10 false *e 0.688,1.438 0.938,1.688 0.25,0.25 10 false *f 2.094,0.344 2.344,0.594 0.25,0.25 10 false *g 0.865,1.771 1.198,2.021 0.333,0.25 10 false *h
*a No. 1 Skid Control ECU
*b No. 1 Reservoir Hose and No. 2 Reservoir Hose
*c Master Cylinder Push Rod Clevis
*d Boot
*e Brake Master Cylinder Reservoir
*f No. 1 Brake Actuator Tube
*g No. 1 Wire Clamp Bracket
*h Brake Booster with Accumulator Pump Assembly


Do not carry the brake booster with master cylinder assembly by the parts shown in the illustration.



PROCEDURE

Hide 1. PRECAUTION

Z101186

CAUTION:
B475753

Be sure to read precaution thoroughly before servicing.

Click here(Click here)


NOTICE:

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click here(Click here)



Hide 2.PERFORM ACCUMULATOR PRESSURE ZERO DOWN

Z101186

Click here(Click here)

Hide 3.DRAIN BRAKE FLUID

Z101186

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.



Hide 73900 5.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

Hide 55308B 8.REMOVE NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY

Hide 47101A 9.REMOVE BRAKE PEDAL RETURN SPRING

Hide 84340 10.REMOVE STOP LIGHT SWITCH ASSEMBLY

Hide 47264A 11.REMOVE PUSH ROD PIN

Hide 82111C 12.DISCONNECT FRONT COMPARTMENT MAIN WIRE

a.
C451667C01
3.865,0.875 4.031,1.208 0.167,0.333 18 true i 3.333,1.083 3.5,1.417 0.167,0.333 18 true ii 2.875,0.073 3.146,0.365 0.271,0.292 18 true iii 3.708,0.375 3.875,0.708 0.167,0.333 18 true ii
V113147

Release the lock lever
V113148

Disconnect the connector


i.

Disconnect the brake fluid level warning switch connector.

NOTICE:

Be careful not to allow any brake fluid to enter the connector.



ii.

Disengage the 2 clamp to disconnect the front compartment main wire from the brake booster with master cylinder assembly.


iii.

Release the lock lever and disconnect the connector from the brake booster with master cylinder assembly.

NOTICE:

Be careful not to allow any brake fluid to enter the connector.




Hide 47210L 13.REMOVE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

a.
C451680N01
0.417,0.063 0.75,0.396 0.333,0.333 18 false i

i.

Remove the 4 nuts and brake booster with master cylinder assembly.

NOTICE:
·

Do not apply excessive force to the brake lines.

·

Be careful not to allow any brake fluid to enter the connector.

·
C453035C01
0.688,0.5 0.938,0.5 false 0.75,1 1,1 false 0.833,1.5 1.083,1.5 false 1.031,1.833 1.281,1.833 false 2.667,1.833 2.917,1.833 false 2.292,1.5 2.458,1.417 2.458,1.417 2.625,1.417 false 2.375,0.667 2.625,0.667 false 1.719,0.99 1.885,0.406 1.885,0.406 2.052,0.406 true 2.677,0.604 3.01,0.854 0.333,0.25 10 false *a 0.573,0.938 0.906,1.188 0.333,0.25 10 false *b 2.969,1.771 3.219,2.021 0.25,0.25 10 false *c 2.677,1.354 2.927,1.604 0.25,0.25 10 false *d 0.51,0.438 0.844,0.604 0.333,0.167 10 false *e 0.688,1.438 0.938,1.688 0.25,0.25 10 false *f 2.094,0.344 2.344,0.594 0.25,0.25 10 false *g 0.865,1.771 1.198,2.021 0.333,0.25 10 false *h
*a No. 1 Skid Control ECU
*b No. 1 Reservoir Hose and No. 2 Reservoir Hose
*c Master Cylinder Push Rod Clevis
*d Boot
*e Brake Master Cylinder Reservoir
*f No. 1 Brake Actuator Tube
*g No. 1 Wire Clamp Bracket
*h Brake Booster with Accumulator Pump Assembly


Do not carry the brake booster with master cylinder assembly by the parts shown in the illustration.





Hide 44785D 14.REMOVE BRAKE MASTER CYLINDER GASKET

a.
C451690


Hide 15.REMOVE BOOSTER BRACKET STOPPER RING

a.
C451691


Hide 16.REMOVE BRAKE BOOSTER BRACKET

a.
C451692


Hide 44785D 17.REMOVE BRAKE MASTER CYLINDER GASKET

a.
C451693


Hide 18.REMOVE NO. 1 RESERVOIR HOSE

Z101186

HINT:

Perform this procedure only when replacement of the No. 1 reservoir hose is necessary.



a.
C451662


Hide 19.REMOVE NO. 2 RESERVOIR HOSE

Z101186

HINT:

Perform this procedure only when replacement of the No. 2 reservoir hose is necessary.



a.
C451664


Hide 20.REMOVE NO. 1 WIRE CLAMP BRACKET

Z101186

HINT:

Perform this procedure only when replacement of the No. 1 wire clamp bracket is necessary.



a.
C451666N01
0.417,0.063 1,0.479 0.583,0.417 18 false i

i.

Using a 5 mm long hexagon socket wrench, remove the bolt and No. 1 wire clamp bracket.