Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › 2011.12–2013.12
RM2170E _54 Brake _057021 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0278020 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1252/52  Brake Booster Pump Motor on Time Abnormally Long  C1253/53  Pump Motor Relay Malfunction  


DESCRIPTION

The skid control ECU detects decreases in the accumulator pressure according to the data from the accumulator pressure sensor, and then starts and stops the pump motor by operating the motor relay.

DTC No. INF Code DTC Detection Condition Trouble Area
C1252/52 311 The pump motor is operating continuously for 178 seconds or more. (When relay malfunction is 98 seconds or more.)
·

Short in motor circuit or motor monitor circuit

·

Motor relay stuck

·

Accumulator pressure sensor malfunction in brake actuator (Brake booster with master cylinder assembly)

·

Skid control ECU (Brake booster with master cylinder assembly)


C1253/53 321 With the IG1 terminal voltage 9.5 V or more, the motor drive monitor remains off for 0.2 seconds or more after a motor drive on request.
·

Open in motor circuit or motor monitor circuit

·

Skid control ECU (Brake booster with master cylinder assembly)


↑ 322 The motor drive monitor remains on for 2 seconds or more after a motor drive off request.
·

Short in motor circuit or motor monitor circuit

·

Skid control ECU (Brake booster with master cylinder assembly)


↑ 323 The skid control ECU internal motor drive logical inconsistency continues for 2 seconds or more. Skid control ECU (Brake booster with master cylinder assembly)
↑ 324 An open circuit in both skid control ECU internal motor relays 1 and 2.
·

Open in motor circuit or motor monitor circuit

·

Skid control ECU (Brake booster with master cylinder assembly)


↑ 325 An open circuit in both skid control ECU internal motor relays 1 and 3. ↑
↑ 326 An open circuit in both skid control ECU internal motor relays 2 and 3. ↑
↑ 327 An open circuit in skid control ECU internal motor relay 1. ↑
↑ 328 An open circuit in skid control ECU internal motor relay 2. ↑
↑ 329 An open circuit in skid control ECU internal motor relay 3. ↑

WIRING DIAGRAM

C256388E03
3.82,3.2 4.976,3.370 1.156,0.170 10 ABS MTR NO. 1 2.775,5.593 3.198,5.740 0.423,0.147 10 MAIN 0.099,8.074 1.439,8.433 1.340,0.360 10 Brake Booster Pump Assembly 5.027,8.147 7.103,8.472 2.077,0.325 10 Skid Control ECU (Brake Booster with Master Cylinder Assembly) 0.847,1.034 1.223,1.203 0.377,0.170 10 BM1 0.829,2.091 1.206,2.260 0.377,0.170 10 BM2 6.132,0.932 6.608,1.101 0.476,0.170 10 MRO1 6.132,3.032 6.585,3.201 0.453,0.170 10 MRI1 6.132,1.973 6.608,2.118 0.477,0.144 10 MRO2 6.132,4.111 6.508,4.281 0.377,0.170 10 MRI2 0.736,5.566 1.167,5.736 0.431,0.170 10 GND1 6.132,5.02 6.563,5.190 0.431,0.170 10 GND 0.727,6.557 1.158,6.727 0.431,0.170 10 GND2 6.132,5.518 6.563,5.688 0.431,0.170 10 GND2 6.132,5.973 6.563,6.143 0.431,0.170 10 GND3 6.132,6.471 6.563,6.641 0.431,0.170 10 GND4 6.132,6.926 6.563,7.095 0.431,0.170 10 GND5 6.132,7.424 6.563,7.594 0.431,0.170 10 GND6 5.93,4.017 6.106,4.159 0.176,0.142 10 2 5.93,2.934 6.160,3.103 0.230,0.170 10 1 5.868,1.886 6.049,2.028 0.181,0.142 10 30 5.875,0.828 6.049,0.966 0.174,0.138 10 29 1.357,6.23 1.587,6.400 0.230,0.170 10 1 2.845,7.203 3.924,7.393 1.079,0.189 10 Auxiliary Battery 1.357,5.238 1.467,5.385 0.110,0.147 10 2 1.288,6.444 1.558,6.585 0.270,0.141 10 A46 1.288,5.448 1.558,5.589 0.269,0.141 10 A45 1.288,1.981 1.558,2.122 0.269,0.141 10 A46 1.357,1.77 1.462,1.914 0.105,0.144 10 2 1.288,0.939 1.558,1.080 0.269,0.141 10 A45 1.357,0.713 1.462,0.857 0.105,0.144 10 1 4.506,4.298 5.548,4.467 1.042,0.170 10 ABS MTR NO. 2 5.87,4.92 6.049,5.059 0.179,0.140 10 28 5.87,5.433 6.049,5.573 0.179,0.140 10 27 5.87,5.9 6.049,6.040 0.179,0.140 10 26 5.87,6.367 6.049,6.507 0.179,0.140 10 25 5.87,6.853 6.049,6.993 0.179,0.140 10 24 5.87,7.32 6.049,7.460 0.179,0.140 10 23 4.721,8.147 5.041,8.317 0.320,0.170 10 A41 4.061,2.934 4.221,3.103 0.160,0.170 10 1 4.537,2.934 4.647,3.081 0.110,0.147 10 2 4.733,4.017 4.894,4.186 0.160,0.170 10 1 5.21,4.017 5.320,4.164 0.110,0.147 10 2 3.445,4.017 3.605,4.186 0.160,0.170 10 1 3.921,4.017 4.031,4.164 0.110,0.147 10 2 3.497,4.298 3.956,4.467 0.458,0.170 10 DC/DC

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake booster with master cylinder assembly) or brake actuator (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION).


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ABS MOTOR RELAY)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Select the Active Test on the intelligent tester (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
ECB* Motor Relay ABS motor relay Relay ON/OFF -

*: Electronically Controlled Brake System



ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
ECB* Motor Relay ABS motor relay / ON or OFF ON: Relay on
OFF: Relay off
-

*: Electronically Controlled Brake System

e.

Check the operating condition of the ABS motor relay when operating it using the intelligent tester.

Result:
Result Proceed to
ABS motor relay in the Data List turns ON/OFF using the Active Test. A
ABS motor relay in the Data List does not change using the Active Test. B




A

2.INSPECT BRAKE BOOSTER PUMP ASSEMBLY

B

6.CHECK HARNESS AND CONNECTOR (MRI TERMINAL)
2.INSPECT BRAKE BOOSTER PUMP ASSEMBLY
a.
U162274E02
0.99,1.656 0.708,2.708 false 1.177,1.656 1.458,2.708 false 2.427,0.552 1.99,1.563 false 1.344,0.552 1.781,1.563 false 2.188,0.323 2.667,0.49 0.479,0.167 10 false GND2 0.479,2.729 0.896,2.896 0.417,0.167 10 false GND1 1.302,2.729 1.656,2.885 0.354,0.156 10 false BM1 1.229,0.323 1.604,0.479 0.375,0.156 10 false BM2 0.177,0.167 0.375,0.302 0.198,0.135 10 false *a 1.74,0.958 2.042,1.115 0.302,0.156 10 false A46 0.938,0.958 1.24,1.115 0.302,0.156 10 false A45

Turn the power switch off (lock).


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the brake booster pump assembly connectors.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A45-1 (BM1) - A45-2 (GND1) Always Below 10 Ω
A46-2 (BM2) - A46-1 (GND2) Always Below 10 Ω
A45-1 (BM1) - A46-2 (BM2) Always Below 1 Ω
A45-2 (GND1) - A46-1 (GND2) Always Below 1 Ω


Text in Illustration
*a Component without harness connected
(Brake Booster Pump Assembly)

Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C




A

3.CHECK HARNESS AND CONNECTOR (GND TERMINAL)

B

REPLACE BRAKE BOOSTER PUMP ASSEMBLY

C

REPLACE BRAKE BOOSTER PUMP ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (GND TERMINAL)
a.
C351654E02
0.385,2.865 0.792,3.115 0.406,0.25 0.344,0.729 0.75,0.979 0.406,0.25 2.323,2.135 1.813,1.656 false 1.052,4.167 1.469,3.75 false 0.115,0.104 0.625,0.323 0.51,0.219 10 false *a 0.417,0.771 0.927,0.99 0.51,0.219 10 false A45 0.458,2.906 0.969,3.125 0.51,0.219 10 false A46 2.177,2.177 2.688,2.396 0.51,0.219 10 false GND1 0.844,4.188 1.354,4.406 0.51,0.219 10 false GND2

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A45-2 (GND1) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω
A46-1 (GND2) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Brake Booster Pump Assembly)



OK

4.READ VALUE USING INTELLIGENT TESTER (ACCUMULATOR PRESSURE SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)

4.READ VALUE USING INTELLIGENT TESTER (ACCUMULATOR PRESSURE SENSOR)
a.

Reconnect the brake booster pump assembly connectors.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the power switch on (IG).


d.

Select the Data List on the intelligent tester (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Accumulator Sensor Accumulator pressure sensor /
Min.: 0.00 V, Max.: 5.00 V
Specified value: 2.90 to 4.20 V When brake fluid is stored in the accumulator: Accumulator pressure changes in accordance with volume of fluid stored in the accumulator


e.

Wait for 30 seconds without depressing the brake pedal.


f.

Check that the accumulator pressure sensor output value change is within the specified range.

OK:

Accumulator pressure sensor output value change is less than 0.55 V.




OK

5.RECONFIRM DTC

NG

8.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SOLENOID VALVE)
5.RECONFIRM DTC
a.

Turn the power switch off (lock).



c.

Turn the power switch on (IG).


d.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs C1252/52 and C1253/53 are not output. A
DTCs C1252/52 and/or C1253/53 are output (for LHD). B
DTCs C1252/52 and/or C1253/53 are output (for RHD). C




A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (MRI TERMINAL)
a.
U183558E01
0.196,0.187 0.380,0.345 0.184,0.158 10 *a 0.265,0.857 0.553,1.015 0.288,0.158 10 A41 1.139,1.787 1.599,2.87 false 0.187,2.883 0.549,3.040 0.362,0.158 10 MRI1 0.878,1.787 0.418,2.87 false 1.367,2.883 1.729,3.040 0.362,0.158 10 MRI2

Turn the power switch off (lock).


b.

Check that the ABS MTR NO. 1 (30 A) and ABS MTR NO. 2 (30 A) fuses are normal.


c.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


d.

Disconnect the skid control ECU (brake booster with master cylinder assembly) connector.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A41-1 (MRI1) - Body ground Always 11 to 14 V
A41-2 (MRI2) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))



OK

7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE BOOSTER PUMP ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (MRI CIRCUIT)

7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE BOOSTER PUMP ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


b.

Disconnect the brake booster pump assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A41-29 (MRO1) - A45-1 (BM1) Always Below 1 Ω
A41-29 (MRO1) - Body ground Always 10 kΩ or higher
A41-30 (MRO2) - A46-2 (BM2) Always Below 1 Ω
A41-30 (MRO2) - Body ground Always 10 kΩ or higher


Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C




A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SOLENOID VALVE)
a.

Select the Active Test on the intelligent tester (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).

HINT:

The Active Test can be performed when the following conditions are met.

·

ABS main relay is on.

·

Shift lever is in P.

·

Parking brake is applied.

·

Vehicle speed is 0 km/h (0 mph).



ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
ECB* Solenoid (SMC/SRC/SCC) Switching solenoid valve (SMC/SRC/SCC) Solenoid ON/OFF Operation sound of solenoid (clicking sound) can be heard

*: Electronically Controlled Brake System


b.

Perform the Active Test of the solenoid using the intelligent tester.



ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Wheel Cylinder Pressure Sensor Wheel cylinder pressure sensor / Min.: 0.00 V, Max.: 5.00 V When brake pedal released: 0.10 to 0.90 V Reading increases when brake pedal is depressed

d.

Check that the output value of the wheel cylinder pressure sensor does not increase.

OK:

The output value of the wheel cylinder pressure sensor does not increase.


HINT:

If the output value increases, there may be brake fluid leaks in the brake actuator.


Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG (for LHD) C
NG (for RHD) D




A

REPLACE BRAKE BOOSTER PUMP ASSEMBLY

B

REPLACE BRAKE BOOSTER PUMP ASSEMBLY

C

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

D

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY