Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM2170E _54 Brake _057021 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0278020 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1247/47  Stroke Sensor Malfunction  C1346/71  Stroke Sensor Zero Point Learning Malfunction (Test Mode DTC)  C1392/48  Stroke Sensor Zero Point Calibration Undone  


DESCRIPTION

The brake pedal stroke sensor assembly sends a signal about the pedal stroke to the skid control ECU.

DTC C1346/71 will be cleared when the brake pedal stroke sensor assembly sends a brake pedal stroke sensor assembly signal or when Test Mode ends. DTC C1346/71 is output only in Test Mode.

DTC No. INF Code DTC Detection Condition Trouble Area
C1247/47 211 Sensor supply voltage (VCM1) is 4.75 V or less, or 5.25 V or more for 0.2 seconds or more.
·

Open or short in brake pedal stroke sensor assembly power supply circuit

·

Improperly connected connector, deformation or corrosion of terminals

·

Skid control ECU (Brake booster with master cylinder assembly)


↑ 212 Sensor output voltage 1 (SKS1) is less than 5.5%, or 94% or more (less than 0.27 V, or 4.7 V or more) of sensor supply voltage (VCM1) for 0.2 seconds or more.
·

Open or short in wire harness

·

Improperly connected connector, deformation or corrosion of terminals

·

Brake pedal stroke sensor assembly


↑ 213 Sensor output voltage 2 (SKS2) is less than 5.5%, or 94% or more (less than 0.27 V, or 4.7 V or more) of sensor supply voltage (VCSK) for 0.2 seconds or more. ↑
↑ 214 Either of the following is detected:
1.

Fluctuation of sensor output 1 (SKS1) is out of specification.

2.

The difference between the present value and last value of sensor output voltage 1 (SKS1) is 8.5% or more (0.43 V or more) of sensor supply voltage (VCM1) for 0.2 seconds or more.


↑
↑ 215 Either of the following is detected:
1.

Fluctuation of sensor output 2 (SKS2) is out of specification.

2.

The difference between the present value and last value of the sensor output voltage 2 (SKS2) is 8.5% or more (0.43 V or more) of the sensor supply voltage (VCM1) for 0.2 seconds or more.


↑
↑ 218 An excessive difference between the change in sensor output 1 (SKS1) and sensor output 2 (SKS2) is detected for 0.2 seconds or more. ↑
↑ 219 Sensor data is invalid for 0.2 seconds or more.
(Skid control ECU internal monitor circuit malfunction.)
↑
↑ 223 Sensor data is invalid for 0.2 seconds or more.
(Open, short, or noise.)
↑
C1392/48 - Zero point calibration of brake pedal stroke sensor assembly is unfinished.
·

Brake pedal stroke sensor zero point calibration incomplete (Initialization and calibration of linear solenoid valve incomplete)

·

Skid control ECU (Brake booster with master cylinder assembly)


C1346/71 - Detected only during Test Mode.
·

Brake pedal stroke sensor assembly

·

Brake pedal stroke sensor assembly circuit



WIRING DIAGRAM

C235540E13
0.108,4.151 2.450,4.305 2.343,0.154 10 Brake Pedal Stroke Sensor Assembly 0.787,1.407 1.179,1.563 0.392,0.156 10 SKS1 0.763,2.937 1.179,3.093 0.415,0.156 10 VCSK 0.866,2.138 1.180,2.294 0.313,0.156 10 SKG 0.787,0.595 1.179,0.751 0.392,0.156 10 SKS2 5.982,1.393 6.365,1.549 0.383,0.156 10 SKS 5.982,2.923 6.397,3.079 0.415,0.156 10 VCSK 5.982,2.124 6.296,2.280 0.313,0.156 10 SKG 5.982,0.581 6.374,0.737 0.392,0.156 10 SKS2 1.287,0.486 1.830,0.649 0.543,0.163 10 2*1, 4*2 1.287,1.283 1.843,1.446 0.557,0.163 10 4*1, 2*2 1.287,2.026 1.394,2.188 0.107,0.163 10 1 1.287,2.831 1.394,2.994 0.107,0.163 10 3 4.699,3.989 4.971,4.131 0.272,0.142 10 A41 5.711,2.831 5.918,2.996 0.208,0.165 10 39 5.711,1.283 5.887,1.448 0.177,0.165 10 42 5.711,2.026 5.887,2.190 0.177,0.165 10 41 5.009,3.989 7.095,4.357 2.086,0.368 10 Skid Control ECU (Brake Booster with Master Cylinder Assembly) 0.108,3.982 0.960,4.124 0.852,0.142 10 A42*1, A43*2 5.711,0.486 5.887,0.651 0.177,0.165 10 40 3.257,3.982 4.006,4.138 0.748,0.156 10 *1: for LHD 3.257,4.268 4.006,4.424 0.748,0.156 10 *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake booster with master cylinder assembly) or brake pedal stroke sensor assembly, perform initialization and calibration of the linear solenoid valve (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION).


HINT:

Check the condition of each related circuit connector before troubleshooting (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).


PROCEDURE

1.CHECK BRAKE PEDAL
a.

Check that the brake pedal and the brake pedal stroke sensor assembly are properly installed and that the pedal can be depressed normally.





NEXT

2.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE PEDAL STROKE SENSOR ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE PEDAL STROKE SENSOR ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


b.

Disconnect the skid control ECU (brake booster with master cylinder assembly) connector and the brake pedal stroke sensor assembly connector.


c.

Check both the connector case and the terminal for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
A41-39 (VCSK) - A42-3 (VCSK) Always Below 1 Ω
A41-39 (VCSK) - Body ground Always 10 kΩ or higher
A41-41 (SKG) - A42-1 (SKG) Always Below 1 Ω
A41-41 (SKG) - Body ground Always 10 kΩ or higher
A41-42 (SKS) - A42-4 (SKS1) Always Below 1 Ω
A41-42 (SKS) - Body ground Always 10 kΩ or higher
A41-40 (SKS2) - A42-2 (SKS2) Always Below 1 Ω
A41-40 (SKS2) - Body ground Always 10 kΩ or higher

for RHD:
Tester Connection Condition Specified Condition
A41-39 (VCSK) - A43-3 (VCSK) Always Below 1 Ω
A41-39 (VCSK) - Body ground Always 10 kΩ or higher
A41-41 (SKG) - A43-1 (SKG) Always Below 1 Ω
A41-41 (SKG) - Body ground Always 10 kΩ or higher
A41-42 (SKS) - A43-2 (SKS1) Always Below 1 Ω
A41-42 (SKS) - Body ground Always 10 kΩ or higher
A41-40 (SKS2) - A43-4 (SKS2) Always Below 1 Ω
A41-40 (SKS2) - Body ground Always 10 kΩ or higher




OK

3.INSPECT SKID CONTROL ECU (SENSOR OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT SKID CONTROL ECU (SENSOR OUTPUT)
a.
U183520E02
1.271,2.281 0.885,2.823 false 1.698,2.281 2.083,2.823 false 0.375,0.24 0.615,0.438 0.24,0.198 10 false *a 0.281,0.938 0.604,1.135 0.323,0.198 10 false A42 0.719,0.938 0.896,1.135 0.177,0.198 10 false *A 0.292,1.375 0.615,1.573 0.323,0.198 10 false A43 0.719,1.365 0.896,1.563 0.177,0.198 10 false *B 0.688,2.854 1.01,3.021 0.323,0.167 10 false SKG 2.031,2.854 2.479,3.021 0.448,0.167 10 false VCSK

Reconnect the skid control ECU (brake booster with master cylinder assembly) connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Condition Specified Condition
A42-3 (VCSK) - A42-1 (SKG) Power switch on (IG) 4.84 to 5.16 V

for RHD
Tester Connection Condition Specified Condition
A43-3 (VCSK) - A43-1 (SKG) Power switch on (IG) 4.84 to 5.16 V


Text in Illustration
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Brake Pedal Stroke Sensor Assembly)

Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG (for LHD) C
NG (for RHD) D




A

B

C

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

D

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY