Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › 2011.12–2013.12
RM2170E _54 Brake _057021 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0278020 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1391/69  Accumulator Leak Malfunction  


DESCRIPTION

The DTC is stored if internal or external brake fluid leaks are detected due to improper sealing in the brake actuator (brake booster with master cylinder assembly) or brake booster pump assembly. Internal leaks are suspected if the pump motor operates frequently without braking.

DTC No. INF Code DTC Detection Condition Trouble Area
C1391/69 351 Either of the following is detected:
1.

Accumulator pressure sensor input does not increase before braking or while the pump motor is operating.

2.

Accumulator pressure sensor input reduction rate exceeds the specification before braking and while the pump motor is not operating.


·

Brake fluid leaks

·

Brake actuator (Brake booster with master cylinder assembly)

(Malfunctioning internal seal, low gas pressure in accumulator, etc.)



CAUTION / NOTICE / HINT

NOTICE:

When replacing the brake actuator (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION).


PROCEDURE

1.CHECK FOR FLUID LEAK
a.

Check that there are no fluid leaks in the brake lines between the brake actuator (brake booster with master cylinder assembly) and the wheel cylinders.


b.

Check that the brakes are not dragging.

OK:

There are no fluid leaks or dragging.




OK

2.RECONFIRM DTC

NG

REPAIR OR REPLACE APPLICABLE PART

2.RECONFIRM DTC

b.

Turn the power switch on (ready).


c.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC C1391/69 is output. A
DTC C1391/69 is not output (for LHD). B
DTC C1391/69 is not output (for RHD). C




A

3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SOLENOID VALVE)

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SOLENOID VALVE)
a.

Turn the power switch off (lock).


b.

Connect the intelligent tester to the DLC3.


c.

Turn the power switch on (IG).


d.

Select the Active Test on the intelligent tester (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).

HINT:

The Active Test can be performed when the following conditions are met.

·

ABS main relay is on.

·

Shift lever is in P.

·

Parking brake is applied.

·

Vehicle speed is 0 km/h (0 mph).



ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
ECB* Solenoid (SMC/SRC/SCC) Switching solenoid valve (SMC/SRC/SCC) Solenoid ON/OFF Operation sound of solenoid (clicking sound) can be heard

*: Electronically Controlled Brake System


e.

Perform the Active Test of the solenoid using the intelligent tester.



ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Wheel Cylinder Pressure Sensor Wheel cylinder pressure sensor / Min.: 0.00 V, Max.: 5.00 V When brake pedal released: 0.10 to 0.90 V Reading increases when brake pedal is depressed

g.

Check that the output value of the wheel cylinder pressure sensor does not increase.

OK:

The output value of the wheel cylinder pressure sensor does not increase.


HINT:

If the output value increases, there may be brake fluid leaks in the brake actuator (brake booster with master cylinder assembly).


Result:
Result Proceed to
The output value of the wheel cylinder pressure sensor increases. A
The output values of the wheel cylinder pressure sensor does not increase (for LHD). B
The output values of the wheel cylinder pressure sensor does not increase (for RHD). C




A

4.REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

REPLACE BRAKE BOOSTER PUMP ASSEMBLY

C

REPLACE BRAKE BOOSTER PUMP ASSEMBLY

4.REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY
a.

Replace the brake actuator (brake booster with master cylinder assembly) (See page Brake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER(for LHD)>REMOVAL for LHD or Brake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER(for RHD)>REMOVAL for RHD).


Result:
Result Proceed to
NEXT (for LHD) A
NEXT (for RHD) B



A

REPLACE BRAKE BOOSTER PUMP ASSEMBLY

B

REPLACE BRAKE BOOSTER PUMP ASSEMBLY