1. PRECAUTION
Make sure to select face mode and max cold before disconnecting the cable from the negative (-) auxiliary battery terminal.
2.RECOVER REFRIGERANT FROM AIR CONDITIONING SYSTEM
3.REMOVE WINDSHIELD WIPER MOTOR AND LINK
55722C
4.REMOVE INNER COWL TOP TO COWL BRACE (for LHD)
55722C
5.REMOVE INNER COWL TOP TO COWL BRACE (for RHD)
55735B
6.REMOVE FRONT AIR SHUTTER SEAL (for LHD)
55735B
7.REMOVE FRONT AIR SHUTTER SEAL (for RHD)
55815E
8.REMOVE FRONT NO. 1 VENTILATOR SEAL (for LHD)
55815E
9.REMOVE FRONT NO. 1 VENTILATOR SEAL (for RHD)
55701J
10.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)
55701J
11.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)
88707
12.DISCONNECT SUCTION PIPE SUB-ASSEMBLY
Remove the bolt and rotate the hook connector.
Disconnect the suction pipe sub-assembly.
Remove the O-ring from the suction pipe sub-assembly.
Seal the openings of the disconnected parts using vinyl tape to prevent the entry of moisture and foreign matter.
88706
13.DISCONNECT LIQUID PIPE SUB-ASSEMBLY
Disconnect the liquid pipe sub-assembly.
Remove the O-ring from the liquid pipe sub-assembly.
Seal the openings of the disconnected parts using vinyl tape to prevent the entry of moisture and foreign matter.
87246A
14.DISCONNECT HEATER WATER OUTLET HOSE A
Using pliers, grip the claws of the clip and slide the clip to disconnect the heater water outlet hose A.
Do not apply excessive force to the heater outlet water hose A.
Prepare a drain pan or cloth in case the coolant leaks.
87209
15.DISCONNECT WATER HOSE SUB-ASSEMBLY
Using pliers, grip the claws of the clip and slide the clip to disconnect the water hose sub-assembly.
Do not apply excessive force to the water hose sub-assembly.
Prepare a drain pan or cloth in case the coolant leaks.
55303B
16.REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY
17.REMOVE STEERING COLUMN ASSEMBLY
89981A
18.REMOVE HYBRID VEHICLE CONTROL ECU
82141
19.DISCONNECT INSTRUMENT PANEL WIRE
82730
20.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (for LHD)
82730
21.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (for RHD)
89650
22.REMOVE POWER STEERING ECU ASSEMBLY (for LHD)
89650
23.REMOVE POWER STEERING ECU ASSEMBLY (for RHD)
899A0
24.REMOVE NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY
899A0A
25.REMOVE NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY
58510D
26.DISCONNECT FRONT FLOOR CARPET ASSEMBLY
Turn back the front floor carpet assembly.
55306A
27.REMOVE NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY (for LHD)
Disengage each clamp.
| *1 | Bolt |
| *2 | Screw |
| *3 | Nut |
Remove the 2 bolts, screw, nut and No. 1 instrument panel brace sub-assembly.
55306A
28.REMOVE NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY (for RHD)
Disengage each clamp.
| *1 | Bolt |
| *2 | Screw |
| *3 | Nut |
Remove the bolt, screw, nut and No. 1 instrument panel brace sub-assembly.
82141
29.DISCONNECT INSTRUMENT PANEL WIRE (for LHD)
for LH Side:
Disconnect each connector.
Disconnect the connector from the connector holder.
Remove the bolt.
Disengage each clamp and disconnect the connector holder.
for RH Side:
Disconnect each connector.
Remove the bolt.
Disengage each clamp and disconnect the connector holder.
Remove the 2 bolts <A> and disconnect the 2 earth wires.
| *1 | Earth Wire | *2 | Bolt <A> |
| *3 | Bolt <B> | - | - |
Remove the bolt <B>.
Disconnect the connector.
Disengage each clamp.
Remove the bolt and disconnect the earth wire.
| *1 | Earth Wire | - | - |
Disconnect the connector.
Disengage each clamp and disconnect the instrument panel wire.
82141
30.DISCONNECT INSTRUMENT PANEL WIRE (for RHD)
for RH Side:
Disconnect each connector.
Disconnect the connector from the connector holder.
Remove the bolt.
Disengage each clamp and disconnect the connector holder.
for LH Side:
Disconnect each connector.
Remove the bolt.
Disengage each clamp and disconnect the connector holder.
Remove the 2 bolts and disconnect the 2 earth wires.
| *1 | Earth Wire | - | - |
Disconnect each connector.
Disengage each clamp.
Remove the bolt <A> and disconnect the earth wire.
| *1 | Earth Wire | *2 | Bolt <A> |
| *3 | Bolt <B> | - | - |
Remove the bolt <B>.
Disconnect the connector.
Disengage each clamp and disconnect the instrument panel wire.
55330B
31.REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY
Remove the 8 bolts and 3 screws, and remove the instrument panel reinforcement.
| *1 | Bolt | *2 | Screw |
55950G
32.REMOVE DEFROSTER NOZZLE ASSEMBLY
Disengage the 2 claws and 3 guides and remove the defroster nozzle assembly.
88539J
33.DISCONNECT DRAIN COOLER HOSE
Disconnect the drain cooler hose.
34.REMOVE AIR CONDITIONER UNIT ASSEMBLY
Remove the 3 bolts and nut, and remove the air conditioner unit assembly.
87050
35.REMOVE AIR CONDITIONING RADIATOR ASSEMBLY (for LHD)
Disconnect the connector.
Remove the 3 screws and air conditioning radiator assembly.
87050
36.REMOVE AIR CONDITIONING RADIATOR ASSEMBLY (for RHD)
Disconnect the connector.
Remove the 3 screws and air conditioning radiator assembly.
88897P
37.REMOVE ASPIRATOR
Disengage the 2 claws and remove the aspirator.
88650N
38.REMOVE AIR CONDITIONING AMPLIFIER ASSEMBLY
Disconnect the connector.
Remove the screw.
Remove the air conditioning amplifier assembly as shown in the illustration.
82210K
39.REMOVE AIR CONDITIONING HARNESS ASSEMBLY (for LHD)
Disengage each clamp.
Disconnect each connector and remove the air conditioning harness assembly.
82210K
40.REMOVE AIR CONDITIONING HARNESS ASSEMBLY (for RHD)
Disengage each clamp.
Disconnect each connector and remove the air conditioning harness assembly.
87201F
41.REMOVE NO. 3 AIR DUCT SUB-ASSEMBLY
Disengage the 3 claws and remove the No. 3 air duct sub-assembly.
If any of the claws of the No. 3 air duct subassembly have been cracked or deformed during removal, make sure to replace the air duct with a new one. Failure to do so may cause the No. 3 air duct sub-assembly to fall off or noise to occur.
87201B
42.REMOVE NO. 2 AIR DUCT SUB-ASSEMBLY
Disengage the 3 claws and remove the No. 2 air duct sub-assembly.
If any of the claws of the No. 2 air duct subassembly have been cracked or deformed during removal, make sure to replace the air duct with a new one. Failure to do so may cause the No. 3 air duct sub-assembly to fall off or noise to occur.