Home › Engine / Hybrid System › 1NZ-FXE (ENGINE CONTROL) › SFI SYSTEM(w/ Canister Pump Module) › from 2017.06
RM2170E _51 Engine / Hybrid System _057003 1NZ-FXE ENGINE CONTROL _0320444 SFI SYSTEM(w/ Canister Pump Module) C

1NZ-FXE ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P219A  Bank 1 Air-Fuel Ratio Imbalance  P219C  Cylinder 1 Air-Fuel Ratio Imbalance  P219D  Cylinder 2 Air-Fuel Ratio Imbalance  P219E  Cylinder 3 Air-Fuel Ratio Imbalance  P219F  Cylinder 4 Air-Fuel Ratio Imbalance  


DESCRIPTION

Refer to P0300.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>P0300

Refer to P2195.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>P2195

DTC No. DTC Detection Condition Trouble Area
P219A The difference in air fuel ratio between the cylinders exceeds the threshold (2 trip detection logic).
·

Fuel injector assembly

·

Intake system

·

Gas leak from exhaust system

·

Ignition system

·

Compression pressure

·

Air fuel ratio sensor (sensor 1)

·

ECM


P219C The difference in air fuel ratio between the cylinders exceeds the threshold (2 trip detection logic).
·

Fuel injector assembly

·

Intake system

·

Gas leak from exhaust system

·

Ignition system

·

Compression pressure

·

Air fuel ratio sensor (sensor 1)

·

ECM


P219D The difference in air fuel ratio between the cylinders exceeds the threshold (2 trip detection logic).
·

Fuel injector assembly

·

Intake system

·

Gas leak from exhaust system

·

Ignition system

·

Compression pressure

·

Air fuel ratio sensor (sensor 1)

·

ECM


P219E The difference in air fuel ratio between the cylinders exceeds the threshold (2 trip detection logic).
·

Fuel injector assembly

·

Intake system

·

Gas leak from exhaust system

·

Ignition system

·

Compression pressure

·

Air fuel ratio sensor (sensor 1)

·

ECM


P219F The difference in air fuel ratio between the cylinders exceeds the threshold (2 trip detection logic).
·

Fuel injector assembly

·

Intake system

·

Gas leak from exhaust system

·

Ignition system

·

Compression pressure

·

Air fuel ratio sensor (sensor 1)

·

ECM



MONITOR DESCRIPTION

Fuel System Air Fuel Ratio Cylinder Imbalance Monitor

The ECM uses the air fuel ratio sensor and crank position sensor to monitor the difference in air fuel ratio between the cylinders caused by differences in injection volume between the cylinders, leakage in the intake or exhaust system, etc.

When the air fuel ratios of the cylinders are lean or rich with respect to each other, the ECM determines that a problem is present and stores a DTC.


Air Fuel Ratio Sensor Monitoring Method: P219A is stored primarily when a rich side imbalance is detected.

When the system detects a difference in the air fuel ratio between the cylinders due to fluctuation of the air fuel ratio sensor output over 1 engine cycle (2 crankshaft revolutions), the system determines that there is a problem.


Crank Position Sensor Monitoring Method: P219C, P219D, P219E and/or P219F are stored primarily when a lean side imbalance is detected.

The system monitors the engine speed variation and when the variation becomes large, the system determines that there is a difference in the air fuel ratio between the cylinders, which it determines to be a problem.


MONITOR STRATEGY

Required Sensors/Components (Main) Air fuel ratio sensor
Crank position sensor
Required Sensors/Components (Related) Mass air flow meter sub-assembly
Engine coolant temperature sensor
Frequency of Operation Once per driving cycle

TYPICAL ENABLING CONDITIONS

Air Fuel Ratio Sensor Monitoring Method
Air fuel ratio sensor status Activated
Engine speed 2400 rpm or higher, and less than 3000 rpm
Engine coolant temperature 75°C (167°F) or higher
Atmospheric pressure 76 kPa(abs) [570 mmHg(abs)] or higher
Fuel system status Closed loop
Mass air flow 15 g/sec. or more, and less than 29 g/sec.

Crank Position Sensor Monitoring Method (First Judgment)
Engine speed 2000 rpm or higher, and less than 2400 rpm
Engine Load 40% or higher, and less than 60%
Engine coolant temperature 75°C (167°F) or higher
Air fuel ratio sensor status Activated
Fuel system status Closed loop
Auxiliary battery voltage 11 V or higher

Crank Position Sensor Monitoring Method (Second Judgment)
Vehicle speed Less than 3 km/h (1.865 mph)
Engine speed 1050 rpm or higher, and less than 1350 rpm
Engine coolant temperature 75°C (167°F) or higher
Air fuel ratio sensor status Activated
Fuel system status Closed loop
Auxiliary battery voltage 11 V or higher

TYPICAL MALFUNCTION THRESHOLDS

P219A: Air Fuel Ratio Sensor Monitoring Method (Bank 1)
Air fuel ratio sensor monitoring method criteria 0.066 or more

Crank Position Sensor Monitoring Method (First Judgment)
Crank position sensor monitoring method criteria (first judgment) 1.5 or more

Crank Position Sensor Monitoring Method (Second Judgment)
Crank position sensor monitoring method criteria (second judgment) 1 or more

HINT:

If the first judgment while driving shows that the value of Engine Speed Fluctuation Average is between 0.5 and 1.5, then second judgment will be performed when the vehicle is stopped and the engine is idling.


CONFIRMATION DRIVING PATTERN

A288663E15
4.729,3.51 4.427,3.51 false 4.427,3.5 4.083,2.625 false 5.167,3.156 4.573,3.156 false 5,3.156 4.896,2.635 false 4.573,3.146 4.406,2.625 false 1.875,2.625 1.979,3.125 false 1.979,3.115 2.563,3.115 false 2.448,3.115 2.375,2.615 false 1.563,2.646 1.729,3.49 false 1.729,3.479 1.885,3.479 false 1.813,0.781 2.219,1.104 0.406,0.323 10 false [C] 0.083,2.448 0.938,2.938 0.854,0.49 10 false Power Switch off 0.573,2.156 1.063,2.51 0.49,0.354 10 false Idling 0.438,1.542 1.208,1.927 0.771,0.385 10 false 40 km/h 0.448,0.906 1.188,1.313 0.74,0.406 10 false 80 km/h 0.365,0.646 1.25,1.104 0.885,0.458 10 false 100 km/h 1.073,2.042 1.563,2.313 0.49,0.271 10 false [A] 1.354,1.135 1.708,1.385 0.354,0.25 10 false [B] 2.313,2.031 2.833,2.333 0.521,0.302 10 false [D] 3.063,0.792 3.49,1.083 0.427,0.292 10 false [E] 3.854,0.75 4.271,1.094 0.417,0.344 10 false [G] 4.323,0.531 4.823,0.979 0.5,0.448 10 false [H] 3.76,3.167 4.052,3.417 0.292,0.25 10 false [F] 4.844,2.042 5.219,2.323 0.375,0.281 10 false [I] 5.573,0.531 6.063,0.906 0.49,0.375 10 false [J] 6.542,3.167 6.906,3.417 0.365,0.25 10 false [K] 0.042,0.083 1.156,0.469 1.115,0.385 10 false Vehicle Speed 6.781,2.583 7.135,2.906 0.354,0.323 10 false Time 1.917,3.396 3.156,3.719 1.24,0.323 10 false 10 to 20 seconds 2.573,3.021 3.844,3.344 1.271,0.323 10 false 1 minute or more 4.76,3.438 5.844,3.76 1.083,0.323 10 false 5 to 15 seconds 5.219,3.083 6.302,3.385 1.083,0.302 10 false 1 minute or more

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

4.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [A].

5.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

CAUTION:

Use the GTS to clear the DTCs. (Do not disconnect the cable from negative (-) auxiliary battery terminal to clear the DTCs.)


6.

Drive the vehicle at 40 km/h (25 mph).

7.

Gradually accelerate the vehicle from 40 km/h (25 mph) to 80 km/h (50 mph) taking approximately 10 to 20 seconds [B].

HINT:

Refer to mass air flow and engine speed in Typical Enabling Conditions, and then accelerate the vehicle to 80 km/h (50 mph).


8.

Drive the vehicle at 80 km/h (50 mph) or more for 1 minute or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Electrical load can be applied while the vehicle is driven.


9.

Idle the engine for 1 minute or more [D].

HINT:

With the shift lever in D.


10.

Repeat steps [B] and [D] above at least 3 times [E].

11.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [F].

12.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



13.

Drive the vehicle at 80 km/h (50 mph).

14.

Gradually accelerate the vehicle from 80 km/h (50 mph) to 100 km/h (62 mph) taking approximately 5 to 15 seconds [G].

HINT:

Refer to mass air flow and engine speed in Typical Enabling Conditions, and then accelerate the vehicle to 100 km/h (62 mph).


15.

Drive the vehicle at 100 km/h (62 mph) or more for 1 minute or more [H].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Electrical load can be applied while the vehicle is driven.


16.

Idle the engine for 1 minute or more [I].

HINT:

With the shift lever in D.


17.

Repeat steps [G] and [I] above at least 2 times [J].

18.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [K].

19.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



20.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

21.

Input the DTC: P219A, P219C, P219D, P219E or P219F.

22.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the following procedure.




CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

When any air-fuel ratio imbalance is detected, the ECM will perform air-fuel ratio feedback control to make the air-fuel ratio close to the stoichiometric level. This may result in an air-fuel ratio imbalance of normal cylinders and DTCs may be stored.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read DTCs.

Result
Result Proceed to
DTC P219A, P219C, P219D, P219E and/or P219F is output A
DTC P219A, P219C, P219D, P219E and/or P219F and other DTCs are output B


HINT:

If any DTCs other than P219A, P219C, P219D, P219E and/or P219F are output, troubleshoot those DTCs first.



A

2.READ VALUE USING GTS (FREEZE FRAME DATA)

B

2.READ VALUE USING GTS (FREEZE FRAME DATA)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>FREEZE FRAME DATA

Freeze Frame Data Items for DTC P219A, P219C, P219D, P219E and/or P219F:
·

Vehicle Speed

·

Engine Speed

·

Calculate Load

·

Short FT B1S1

·

Long FT B1S1

·

Cylinder #1 Misfire Count to Cylinder #4 Misfire Count


HINT:

When the sum of Short FT and Long FT is positive, the engine is running lean, and when the sum is negative, the engine is running rich.


Air Fuel Ratio Sensor Monitoring Method (P219A) Crank Position Sensor Monitoring Method (P219C, P219D, P219E and P219F) Note
DTCs are output DTC is output (Only one DTC relating to a single cylinder is output) Malfunctioning of cylinders detected by Crank Position Sensor Monitoring Method is primarily suspected
DTCs are output DTCs are output (Multiple DTCs relating to multiple cylinders are output) Malfunctioning of cylinders except ones detected by Crank Position Sensor Monitoring Method is primarily suspected.*1
DTCs are not output DTCs are output Malfunctioning of cylinders detected by Crank Position Sensor Monitoring Method is primarily suspected.
DTCs are output DTCs are not output Malfunctioning of the bank detected by Air Fuel Ratio Sensor Monitoring Method is primarily suspected

*1: When any air-fuel ratio imbalance is detected, the ECM will perform air-fuel ratio feedback control to make the air-fuel ratio close to the stoichiometric level. This may result in an air-fuel ratio imbalance of normal cylinders and DTCs may be stored.



NEXT

3.READ DTC OUTPUT
3.READ DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


e.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

HINT:
·

If any misfire count ("Cylinder #1 Misfire Count" to "Cylinder #4 Misfire Count) increases while idling or driving the vehicle, proceed to step 6.

·

Perform inspections while focusing on the cylinder whose misfire count has increased.




f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Read the DTCs.

Result
Result Proceed to
P219A is output A
DTC P219A and P219C, P219D, P219E or P219F is output B
DTC P219C, P219D, P219E and/or P219F is output



A

4.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME)

B

6.CHECK INTAKE SYSTEM
4.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


e.

Warm up the engine.

HINT:

The A/C switch and all accessory switches should be off.



f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume / Data List / Cylinder #1 to #4 Misfire Count.

HINT:

When the "Control the Injection Volume" Active Test is selected (injection volume is 0%), if a misfire count increases, proceed to step 6 (Check Intake System).



g.

Perform the Control the Injection Volume operation with the engine idling.


h.

Check the misfire counts ("Cylinder #1 Misfire Count" to "Cylinder #4 Misfire Count") while decreasing the injection volume in 5% increments.

NOTICE:

Do not decrease the injection volume by higher than 20%.


Result:

The cylinder whose misfire count has not increased can be assumed to be running rich. Therefore, perform inspections while focusing on that cylinder.




NEXT

5.CHECK FOR EXHAUST GAS LEAK
5.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No exhaust gas leaks.


HINT:

Perform "Inspection After Repair" after repairing or replacing the exhaust system.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION




OK

6.CHECK INTAKE SYSTEM

NG

REPAIR OR REPLACE EXHAUST SYSTEM

6.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks.

Click hereEngine / Hybrid System>1NZ-FXE INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION

OK:

No leaks in intake system.


HINT:

Perform "Inspection After Repair" after repairing or replacing the intake system.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION




OK

7.INSPECT SPARK PLUG

NG

REPAIR OR REPLACE INTAKE SYSTEM

7.INSPECT SPARK PLUG
a.

Inspect the spark plug of the imbalanced cylinder.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the spark plug.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION




OK

8.CHECK FOR SPARK (SPARK TEST)

NG

8.CHECK FOR SPARK (SPARK TEST)
a.

Perform a spark test.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION

HINT:
·

If the result of the spark test is normal, proceed to the next step.

·

Perform "Inspection After Repair" after repairing or replacing the ignition system.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION





NEXT

9.CHECK CYLINDER COMPRESSION PRESSURE
9.CHECK CYLINDER COMPRESSION PRESSURE
a.

Measure the cylinder compression pressure of the misfiring cylinder.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION

HINT:

Perform "Inspection After Repair" after repairing or replacing the engine assembly.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION




OK

10.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR ASSEMBLY)

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

10.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR ASSEMBLY)

OK

11.CHECK FUEL INJECTOR ASSEMBLY OF IMBALANCE CYLINDER

NG

11.CHECK FUEL INJECTOR ASSEMBLY OF IMBALANCE CYLINDER
a.

Check the fuel injector injection [whether fuel volume is high or low, and whether injection pattern is poor].

Click hereEngine / Hybrid System>1NZ-FXE FUEL>FUEL INJECTOR>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the fuel injector assembly.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION




OK

12.CHECK FOR CAUSE OF FAILURE

NG

REPLACE FUEL INJECTOR ASSEMBLY

12.CHECK FOR CAUSE OF FAILURE
a.

If the diagnosis procedure has been performed and the malfunctioning part cannot be determined, perform the following inspection.


b.

Check for deposits on the intake valves.

HINT:

The DTC may have been stored due to deposits that have accumulated in the intake valve. Therefore, remove the cylinder head and inspect the intake valves.



c.

Check for deposits in the EGR delivery chamber.

HINT:

The DTC may have been stored due to deposits that have accumulated in the EGR delivery chamber. Therefore, remove and inspect the EGR delivery chamber.




NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


e.

Check for DTCs.

Result:

DTCs are not output.




NEXT

END