When the engine misfires, high concentrations of hydrocarbons (HC) enter the exhaust gas. Extremely high hydrocarbon concentration levels can cause an increase in exhaust emission levels. Extremely high concentrations of hydrocarbons can also cause increases in the three-way catalytic converter temperature, which may cause damage to the three-way catalytic converter. To prevent this increase in emissions and to limit the possibility of thermal damage, the ECM monitors the misfire count. When the temperature of the three-way catalytic converter reaches the point of thermal degradation, the ECM blinks the MIL. To monitor misfires, the ECM uses both the cam position sensor and the crank position sensor. The cam position sensor is used to identify any misfiring cylinders and the crank position sensor is used to measure variations in the crankshaft rotation speed. Misfires are counted when the crankshaft rotation speed variations exceed predetermined thresholds. If the misfire count exceeds the threshold levels, and could cause emission control system performance deterioration, the ECM illuminates the MIL and stores a DTC.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0300 | Simultaneous misfiring of several cylinders occurs and one of the following conditions is met (2 trip detection logic).
·
A misfire occurs that may damage the three-way catalytic converter (MIL blinks when detect immediately). ·
An emission deterioration misfire occurs (MIL illuminates). |
·
Open or short in engine wire harness ·
Connector connection ·
Vacuum hose connections ·
Ignition system ·
Fuel injector assembly ·
Fuel pressure ·
Mass air flow meter sub-assembly ·
Engine coolant temperature sensor ·
Compression pressure ·
Valve clearance ·
Valve timing ·
PCV valve and hose ·
PCV hose connections ·
Intake system ·
EGR valve assembly ·
ECM |
| P0301
P0302 P0303 P0304 |
Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic).
·
A misfire occurs that may damage the three-way catalytic converter (MIL blinks when detect immediately). ·
An emission deterioration misfire occurs (MIL illuminates). |
When DTCs for misfiring cylinders are randomly stored, but DTC P0300 is not stored, it indicates that misfires have been detected in different cylinders at different times. DTC P0300 is only stored when several misfiring cylinders are detected at the same time.
The ECM illuminates the MIL and stores a DTC when either one of the following conditions, which could cause emission deterioration, is detected (2 trip detection logic).
Within the first 1000 crankshaft revolutions after the engine starts, an excessive number of misfires (approximately 10 to 70 misfires per 1000 crankshaft revolutions) occurs once.
An excessive number of misfires (approximately 10 to 70 misfires per 1000 crankshaft revolutions) occurs a total of 4 times.
The ECM flashes the MIL (immediate detection logic) and stores a DTC (2 trip detection logic) when either one of the following conditions, which could cause damage to the three-way catalytic converter, is detected.
At a high engine speed, a sufficient amount of misfires to damage the catalyst occurring within 200 crankshaft revolutions is detected once.
At a normal engine speed, a sufficient amount of misfires to damage the catalyst occurring within 200 crankshaft revolutions is detected 3 times.
| Required Sensors/Components (Main) | Crank position sensor
Cam position sensor |
| Required Sensors/Components (Related) | Engine coolant temperature
Intake air temperature sensor Mass air flow meter sub-assembly |
| Frequency of Operation | Continuous |
| Either of the following conditions is met | A or B |
| A. Engine coolant temperature at engine start | Higher than -7°C (19°F) |
| B. Engine coolant temperature | Higher than 20°C (68°F) |
| Fuel cut | Off |
| First 1000 revolutions after engine start, or during check mode | Crankshaft 1000 revolutions |
| Except above | Crankshaft 1000 revolutions x 4 |
| All of the following conditions 1, 2, 3 and 4 met | Crankshaft 200 revolutions x 3 |
| Except above (MIL blinks immediately) | Crankshaft 200 revolutions |
| 1. Driving cycles | 1st |
| 2. Check mode | Off |
| 3. Engine speed | Less than 3000 rpm |
| 4. Intake air amount per revolution | Less than 0.52 g/rev. |
| Misfire rate | 1.8% or higher |
| Number of misfires per 200 revolutions | 113 or more (varies with intake air amount and engine speed) |
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Record the DTC(s) and freeze frame data.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Put the engine in inspection mode (maintenance mode).
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE
Using the GTS, switch the ECM from normal mode to check mode.
Read the misfire counts of each cylinder, Cylinder #1 Misfire Count to Cylinder #4 Misfire Count, with the engine idling. If any misfire count is displayed, skip the following confirmation driving pattern.
Drive the vehicle so that the vehicle conditions displayed in Misfire RPM and Misfire Load of the Data List are the same as the freeze frame data. Perform this step several times.
In order to store misfire DTCs, it is necessary to operate the vehicle for the period of time shown in the table below, confirm the Misfire RPM and Misfire Load in the Data List.
| Engine speed | Duration |
|---|---|
| Idling | 4.5 minutes or more |
| 1000 | 4.5 minutes or more |
| 2000 | 2.5 minutes or more |
| 3000 | 1.5 minutes or more |
Check whether misfires have occurred by checking DTCs and freeze frame data.
Do not turn the power switch off until the output DTC(s) and freeze frame data have been recorded. When the ECM returns to normal mode (default), the stored DTC(s), freeze frame data and other data are cleared.
Record the DTC(s), freeze frame data and misfire counts.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the power switch off and wait for at least 30 seconds.
Refer to DTC P0102 for the mass air flow meter sub-assembly circuit.
Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>P0102
Refer to Fuel Injector Circuit.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
If any DTCs other than misfire DTCs are output, troubleshoot those DTCs first.
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
If the misfire does not recur when the vehicle is brought to the workshop, reproduce the conditions stored in the ECM as freeze frame data.
If the misfire still cannot be reproduced even though the conditions stored in the ECM as freeze frame data have been reproduced, one of the following factors is considered to be a possible cause of the problem:
There was insufficient fuel in the tank.
Improper fuel was used.
The spark plugs have been contaminated.
The problem requires further diagnosis.
After finishing repairs, check the misfire counts of the cylinders (Cylinder #1 Misfire Count to Cylinder #4 Misfire Count).
Be sure to confirm that no misfiring cylinder DTCs are stored again by conducting the confirmation driving pattern after finishing repairs.
When one of Short FT B1S1 or Long FT B1S1 in the freeze frame data is outside the range of +/-20%, the air fuel ratio may be rich (-20% or less) or lean (20% or higher).
When Coolant Temp in the freeze frame data is less than 75°C (167°F), the misfires have occurred only while warming up the engine.
An extremely imbalanced drive wheel which causes body vibration may cause misfire DTCs to be stored.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P0300, P0301, P0302, P0303 and/or P0304 are output | A |
| DTC P0300, P0301, P0302, P0303 and/or P0304 and other DTCs are output | B |
If any DTCs other than P0300, P0301, P0302, P0303 and/or P0304 are output, troubleshoot those DTCs first.
A
B
Check the PCV hose connections.
Click hereEngine / Hybrid System>1NZ-FXE EMISSION CONTROL>PCV VALVE>COMPONENTS
PCV valve and hose are correctly connected and are not damaged.
OK
NG
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Gas Misfire / Misfire RPM and Misfire Load.
Read and note the Misfire RPM and Misfire Load values.
The Misfire RPM and Misfire Load values indicate the vehicle conditions under which the misfire occurred.
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Put the engine in inspection mode (maintenance mode).
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE
Enter the following menus: Powertrain / Engine and ECT / Data List / Gas Misfire / Cylinder #1 Misfire Count, Cylinder #2 Misfire Count, Cylinder #3 Misfire Count and Cylinder #4 Misfire Count.
Start the engine and allow the engine to idle.
Read each value for Cylinder #1 Misfire Count to Cylinder #4 Misfire Count displayed on the GTS. If no misfire counts occur in any cylinders, perform procedure [A] and [B] and then check the misfire counts again.
Drive the vehicle with the Misfire RPM and Misfire Load noted in the "Read Value Using GTS (Misfire RPM and Misfire Load)" procedures above [A].
Read the Cylinder #1 Misfire Count to Cylinder #4 Misfire Count or DTCs displayed on the GTS [B].
| Result | Proceed to |
|---|---|
| Most misfires occur in only 1 or 2 cylinders | A |
| 3 cylinders or more have equal misfire counts | B |
If it is difficult to reproduce misfires for each cylinder, check the Data List item called Misfire Margin. Try to find vehicle driving conditions that lower the Misfire Margin value. Values above 30% are considered normal.
If the freeze frame data record of the engine coolant temperature is less than 75°C (167°F), the misfire may be detected only when the engine is cold.
A
B
Inspect the spark plug of the misfiring cylinder.
Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION
Perform "Inspection After Repair" after replacing the spark plug.
Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION
OK
NG
Perform a spark test.
Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION
If the result of the spark test is normal, proceed to the next step.
Perform "Inspection After Repair" after repairing or replacing the ignition system.
Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION
NEXT
Measure the cylinder compression pressure of the misfiring cylinder.
Click hereEngine / Hybrid System>1NZ-FXE (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION
Perform "Inspection After Repair" after repairing or replacing the engine assembly.
Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION
OK
NG
Disconnect the ECM connector.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C10-20 (#10) - C10-51 (E01) | Power switch on (IG) | 11 to 14 V |
| C10-17 (#20) - C10-51 (E01) | Power switch on (IG) | 11 to 14 V |
| C10-18 (#30) - C10-51 (E01) | Power switch on (IG) | 11 to 14 V |
| C10-19 (#40) - C10-51 (E01) | Power switch on (IG) | 11 to 14 V |
| *a | Front view of wire harness connector
(to ECM) |
OK
NG
Check the fuel injector assembly injection (whether fuel volume is high or low, and whether injection pattern is poor).
Click hereEngine / Hybrid System>1NZ-FXE FUEL>FUEL INJECTOR>INSPECTION
Perform "Inspection After Repair" after replacing the fuel injector assembly.
Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION
OK
NG
Check the valve clearance.
Click hereEngine / Hybrid System>1NZ-FXE (ENGINE MECHANICAL)>VALVE CLEARANCE>ADJUSTMENT
OK
NG
Check the intake system for vacuum leaks.
Click hereEngine / Hybrid System>1NZ-FXE INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION
No leaks from intake system.
Perform "Inspection After Repair" after repairing or replacing the intake system.
Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION
OK
NG
Check the fuel pressure.
Click hereEngine / Hybrid System>1NZ-FXE FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION
OK
NG
OK
NG
OK
NG
OK
NG
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Put the engine in inspection mode (maintenance mode).
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
The A/C switch and all accessory switches should be off.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position / Primary / Throttle Idle Position and MAP.
Confirm that the Throttle Idle Position is ON and check the MAP value in the Data List while performing the Active Test.
Do not leave the EGR valve open for 10 seconds or more during the Active Test.
Be sure to return the EGR valve to step 0 when the Active Test is completed.
Do not open the EGR valve 30 steps or more during the Active Test.
MAP change in response to EGR step position when Throttle Idle Position is ON in Data List.
| - | EGR Step Position (Active Test) | |
|---|---|---|
| 0 Steps | 0 to 30 Steps | |
| MAP
(Data List) |
(EGR valve is fully closed) | MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed |
While performing the Active Test, if the increase in the value of MAP is small, the EGR valve assembly may be a malfunctioning.
Even if the EGR valve assembly is malfunctioning, rough idling or an increase in the value of MAP may occur while performing the Active Test. However, the amount that the value of MAP increases will be smaller than normal.
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
A
B
Remove the EGR valve assembly.
Click hereEngine / Hybrid System>1NZ-FXE EMISSION CONTROL>EGR VALVE>REMOVAL
Check if the EGR valve is stuck open.
EGR valve is tightly closed.
Perform "Inspection After Repair" after replacing the EGR valve assembly.
Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION
OK
NG
Check the intake system for vacuum leaks.
Click hereEngine / Hybrid System>1NZ-FXE INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION
No leaks from intake system.
Perform "Inspection After Repair" after repairing or replacing the intake system.
Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION
OK
NG
Check the fuel pressure.
Click hereEngine / Hybrid System>1NZ-FXE FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION
OK
NG
OK
NG
OK
NG
OK
NG
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Put the engine in inspection mode (maintenance mode).
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
The A/C switch and all accessory switches should be off.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position / Primary / Throttle Idle Position and MAP.
Confirm that the Throttle Idle Position is ON and check the MAP value in the Data List while performing the Active Test.
Do not leave the EGR valve open for 10 seconds or more during the Active Test.
Be sure to return the EGR valve to step 0 when the Active Test is completed.
Do not open the EGR valve 30 steps or more during the Active Test.
MAP change in response to EGR step position when Throttle Idle Position is ON in Data List.
| - | EGR Step Position (Active Test) | |
|---|---|---|
| 0 Steps | 0 to 30 Steps | |
| MAP
(Data List) |
(EGR valve is fully closed) | MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed |
While performing the Active Test, if the increase in the value of MAP is small, the EGR valve assembly may be a malfunctioning.
Even if the EGR valve assembly is malfunctioning, rough idling or an increase in the value of MAP may occur while performing the Active Test. However, the amount that the value of MAP increases will be smaller than normal.
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
A
B
Remove the EGR valve assembly.
Click hereEngine / Hybrid System>1NZ-FXE EMISSION CONTROL>EGR VALVE>REMOVAL
Check if the EGR valve is stuck open.
EGR valve is tightly closed.
Perform "Inspection After Repair" after replacing the EGR valve assembly.
Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION
OK
NG
Inspect the spark plug of the misfiring cylinder.
Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION
Perform "Inspection After Repair" after replacing the spark plug.
Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION
OK
NG
Perform a spark test.
Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION
If the result of the spark test is normal, proceed to the next step.
Perform "Inspection After Repair" after repairing or replacing the ignition system.
Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION
NEXT
Measure the cylinder compression pressure of the misfiring cylinder.
Click hereEngine / Hybrid System>1NZ-FXE (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION
Perform "Inspection After Repair" after repairing or replacing the engine assembly.
Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION
OK
NG
Disconnect the ECM connector.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C10-20 (#10) - C10-51 (E01) | Power switch on (IG) | 11 to 14 V |
| C10-17 (#20) - C10-51 (E01) | Power switch on (IG) | 11 to 14 V |
| C10-18 (#30) - C10-51 (E01) | Power switch on (IG) | 11 to 14 V |
| C10-19 (#40) - C10-51 (E01) | Power switch on (IG) | 11 to 14 V |
| *a | Front view of wire harness connector
(to ECM) |
OK
NG
Check the fuel injector assembly injection (whether fuel volume is high or low, and whether injection pattern is poor).
Click hereEngine / Hybrid System>1NZ-FXE FUEL>FUEL INJECTOR>INSPECTION
Perform "Inspection After Repair" after replacing the fuel injector assembly.
Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION
OK
NG
Check the valve clearance.
Click hereEngine / Hybrid System>1NZ-FXE (ENGINE MECHANICAL)>VALVE CLEARANCE>ADJUSTMENT
OK
NG
Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter sub-assembly and ECM.
Repair any problems.
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Clear the DTCs.
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on (IG).
Turn the GTS on.
Put the engine in inspection mode (maintenance mode).
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0300, P0301, P0302, P0303 or P0304.
Check the DTC judgment result.
| Result | Proceed to |
|---|---|
| ABNORMAL
(DTC P0300, P0301, P0302, P0303 and/or P0304 is output) |
A |
| NORMAL
(DTCs are not output) |
B |
A
B
OK
NG
Replace the mass air flow meter sub-assembly.
Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>MASS AIR FLOW METER>REMOVAL
If the results of the inspections performed in steps 14 and 21 indicated no problem, proceed to the next step without replacing the mass air flow meter sub-assembly.
Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.
Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Clear the DTCs.
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on (IG).
Turn the GTS on.
Put the engine in inspection mode (maintenance mode).
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0300, P0301, P0302, P0303 or P0304.
Check the DTC judgment result.
| Result | Proceed to |
|---|---|
| NORMAL
(DTCs are not output) |
A |
| ABNORMAL
(DTC P0300, P0301, P0302, P0303 and/or P0304 is output) |
B |
A
B
Check the fuel lines for leaks or blockage.
Perform "Inspection After Repair" after replacing the fuel pump with filter assembly.
Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION
OK
NG
OK
NG
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Clear the DTCs.
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on (IG).
Turn the GTS on.
Put the engine in inspection mode (maintenance mode).
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0300, P0301, P0302, P0303 or P0304.
Check the DTC judgment result.
| Result | Proceed to |
|---|---|
| ABNORMAL
(DTC P0300, P0301, P0302, P0303 and/or P0304 is output) |
A |
| NORMAL
(DTCs are not output) |
B |
A
B
Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter sub-assembly and ECM.
Repair any problems.
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Clear the DTCs.
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on (IG).
Turn the GTS on.
Put the engine in inspection mode (maintenance mode).
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0300, P0301, P0302, P0303 or P0304.
Check the DTC judgment result.
| Result | Proceed to |
|---|---|
| ABNORMAL
(DTC P0300, P0301, P0302, P0303 and/or P0304 is output) |
A |
| NORMAL
(DTCs are not output) |
B |
A
B
OK
NG
Replace the mass air flow meter sub-assembly.
Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>MASS AIR FLOW METER>REMOVAL
If the results of the inspections performed in steps 14 and 21 indicated no problem, proceed to the next step without replacing the mass air flow meter sub-assembly.
Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.
Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION
NEXT
Connect the GTS to the DLC3.
Turn the powerswitch on (IG).
Turn the GTS on.
Clear the DTCs.
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on (IG).
Turn the GTS on.
Put the engine in inspection mode (maintenance mode).
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0300, P0301, P0302, P0303 or P0304.
Check the DTC judgment result.
| Result | Proceed to |
|---|---|
| ABNORMAL
(DTC P0300, P0301, P0302, P0303 and/or P0304 is output) |
A |
| NORMAL
(DTCs are not output) |
B |
A
B