When the engine misfires, high concentrations of hydrocarbons (HC) enter the exhaust gas. Extremely high hydrocarbon concentration levels can cause an increase in exhaust emission levels. Extremely high concentrations of hydrocarbons can also cause increases in the three-way catalytic converter temperature, which may cause damage to the three-way catalytic converter. To prevent this increase in emissions and to limit the possibility of thermal damage, the ECM monitors the misfire count. When the temperature of the three-way catalytic converter reaches the point of thermal degradation, the ECM blinks the MIL. To monitor misfires, the ECM uses both the camshaft position sensor and the crankshaft position sensor. The camshaft position sensor is used to identify any misfiring cylinders and the crankshaft position sensor is used to measure variations in the crankshaft rotation speed. Misfires are counted when the crankshaft rotation speed variations exceed predetermined thresholds. If the misfire count exceeds the threshold levels, and could cause emission control system performance deterioration, the ECM illuminates the MIL and stores a DTC.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0300 | Simultaneous misfiring of several cylinders occurs and one of the following conditions is met (2 trip detection logic).
·
A misfire occurs that may damage the three-way catalytic converter (MIL blinks when detect immediately). ·
An emission deterioration misfire occurs (MIL illuminates). |
·
Open or short in engine wire harness ·
Connector connection ·
Vacuum hose connections ·
Ignition system ·
Fuel injector assembly ·
Fuel pressure ·
Mass air flow meter sub-assembly ·
Engine coolant temperature sensor ·
Compression pressure ·
Valve timing ·
PCV valve and hose ·
PCV hose connections ·
Intake system ·
EGR valve assembly ·
ECM |
| P0301
P0302 P0303 P0304 |
Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic).
·
A misfire occurs that may damage the three-way catalytic converter (MIL blinks when detect immediately). ·
An emission deterioration misfire occurs (MIL illuminates). |
When DTCs for misfiring cylinders are randomly stored, but DTC P0300 is not stored, it indicates that misfires have been detected in different cylinders at different times. DTC P0300 is only stored when several misfiring cylinders are detected at the same time.
The ECM illuminates the MIL and stores a DTC when the following condition, which could cause emission deterioration, is detected (2 trip detection logic).
An excessive number of misfires (approximately 50 to 80 misfires per 1000 crankshaft revolutions) occurs a total of 4 times.
The ECM flashes the MIL (immediate detection logic) and stores a DTC (2 trip detection logic) when either one of the following conditions, which could cause damage to the three-way catalytic converter, is detected.
At a high engine speed, a sufficient amount of misfires to damage the catalyst occurring within 200 crankshaft revolutions is detected once.
At a normal engine speed, a sufficient amount of misfires to damage the catalyst occurring within 200 crankshaft revolutions is detected 3 times.
| Required Sensors/Components (Main) | Crankshaft position sensor
Camshaft position sensor |
| Required Sensors/Components (Related) | Engine coolant temperature sensor
Intake air temperature sensor Mass air flow meter sub-assembly |
| Frequency of Operation | Continuous |
| Intake air temperature | Higher than -10°C (14°F) |
| Either of the following conditions is met | A or B |
| A. Engine coolant temperature at engine start | Higher than -7°C (19°F) |
| B. Engine coolant temperature | Higher than 20°C (68°F) |
| Duration | Crankshaft 1000 revolutions x 4 |
| Duration | Crankshaft 200 revolutions x 3 |
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Record the DTC(s) and freeze frame data.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).
Using the GTS, switch the ECM from normal mode to check mode (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>CHECK MODE PROCEDURE).
Read the misfire counts of each cylinder, Cylinder #1 Misfire Count to Cylinder #4 Misfire Count, with the engine idling. If any misfire count is displayed, skip the following confirmation driving pattern.
Drive the vehicle so that the vehicle conditions displayed in Misfire RPM and Misfire Load of the Data List are the same as the freeze frame data. Perform this step several times.
In order to store misfire DTCs, it is necessary to operate the vehicle for the period of time shown in the table below, confirm the Misfire RPM and Misfire Load in the Data List.
| Engine speed | Duration |
|---|---|
| Idling | 4.5 minutes or more |
| 1000 | 4.5 minutes or more |
| 2000 | 2.5 minutes or more |
| 3000 | 1.5 minutes or more |
Check whether misfires have occurred by checking DTCs and freeze frame data.
Do not turn the power switch off until the output DTC(s) and freeze frame data have been recorded. When the ECM returns to normal mode (default), the stored DTC(s), freeze frame data and other data are cleared.
Record the DTC(s), freeze frame data and misfire counts.
Turn the power switch off and wait for at least 30 seconds.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Refer to Fuel Injector Circuit (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>Fuel Injector Circuit).
Mass air flow meter sub-assembly circuit: Refer to DTC P0102 (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>P0102).
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
If any DTCs other than misfire DTCs are output, troubleshoot those DTCs first.
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.
If the misfire does not recur when the vehicle is brought to the workshop, reproduce the conditions stored in the ECM as freeze frame data.
If the misfire still cannot be reproduced even though the conditions stored in the ECM as freeze frame data have been reproduced, one of the following factors is considered to be a possible cause of the problem:
There was insufficient fuel in the tank.
Improper fuel is used.
The spark plugs have been contaminated.
The problem requires further diagnosis.
After finishing repairs, check the misfire counts of the cylinders Cylinder #1 Misfire Count to Cylinder #4 Misfire Count.
Be sure to confirm that no misfiring cylinder DTCs are stored again by conducting the confirmation driving pattern after finishing repairs.
When one of Short FT B1S1 or Long FT B1S1 in the freeze frame data is outside the range of +/-20%, the air fuel ratio may be rich (-20% or less) or lean (20% or higher).
When the Coolant Temp in the freeze frame data is less than 75°C (167°F), the misfire has occurred only while warming up the engine.
An extremely imbalanced drive wheel which causes body vibration may cause misfire DTCs to be stored.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P0300, P0301, P0302, P0303 and/or P0304 are output | A |
| DTC P0300, P0301, P0302, P0303 and/or P0304 and other DTCs are output | B |
If any DTCs other than P0300, P0301, P0302, P0303 and/or P0304 are output, troubleshoot those DTCs first.
A
B
Check the PCV hose connections (See page Engine / Hybrid System>2ZR-FXE (EMISSION CONTROL)>PCV VALVE>COMPONENTS).
PCV valve and hose are correctly connected and are not damaged.
OK
NG
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Misfire RPM and Misfire Load.
Read and note the Misfire RPM and Misfire Load values.
The Misfire RPM and Misfire Load values indicate the vehicle conditions under which the misfire occurred.
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Cylinder #1 (to #4) Misfire Count.
Start the engine and allow the engine to idle.
Read each value for Cylinder #1 (to #4) Misfire Count displayed on the GTS. If no misfire counts occur in any cylinders, perform steps [A] and [B], and then check the misfire counts again.
Drive the vehicle with the Misfire RPM and Misfire Load noted in the read value using the GTS (Misfire RPM and Misfire Load) procedures above [A].
Read Cylinder #1 (to #4) Misfire Count or the DTCs displayed on the GTS [B].
| Misfire Count | Proceed to |
|---|---|
| Most misfires occur in only 1 or 2 cylinders | A |
| 3 cylinders or more have equal misfire counts | B |
If it is difficult to reproduce misfires for each cylinder, check the Data List item called Misfire Margin. Try to find vehicle driving conditions that lower the Misfire Margin value. Values above 30% are considered normal.
If the freeze frame data record of the engine coolant temperature is less than 75°C (167°F), it may only be possible to detect the misfire when the engine is cold.
A
B
Inspect the spark plug of the misfiring cylinder (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION).
OK
NG
Perform a spark test (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION).
If the result of the spark test is normal, proceed to the next step.
NEXT
Measure the cylinder compression pressure of the misfiring cylinder (See page Engine / Hybrid System>2ZR-FXE (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION).
OK
NG
Disconnect the ECM connector.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D28-85 (#10) - D28-109 (E01) | Power switch on (IG) | 11 to 14 V |
| D28-84 (#20) - D28-109 (E01) | Power switch on (IG) | 11 to 14 V |
| D28-83 (#30) - D28-109 (E01) | Power switch on (IG) | 11 to 14 V |
| D28-82 (#40) - D28-109 (E01) | Power switch on (IG) | 11 to 14 V |
| *a | Front view of wire harness connector
(to ECM) |
OK
NG
Check the fuel injector assembly injection (whether fuel volume is high or low, and whether injection pattern is poor) (See page Engine / Hybrid System>2ZR-FXE (FUEL)>FUEL INJECTOR>INSPECTION).
OK
NG
Check the intake system for vacuum leaks (See page Engine / Hybrid System>2ZR-FXE (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION).
No leaks in intake system.
OK
NG
Check the fuel pressure (See page Engine / Hybrid System>2ZR-FXE (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION).
OK
NG
OK
NG
OK
NG
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Clear the DTCs (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on (IG).
Turn the GTS on.
Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0300, P0301, P0302, P0303 or P0304.
Check the DTC judgment result.
| Result | Proceed to |
|---|---|
| ABNORMAL
(DTC P0300, P0301, P0302, P0303 and/or P0304 is output) |
A |
| NORMAL
(DTC is not output) |
B |
A
B
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
The A/C switch and all accessory switches should be off.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position / All Data / MAP.
Check the MAP value in the Data List while performing the Active Test.
Do not leave the EGR valve open for 10 seconds or more during the Active Test.
Be sure to return the EGR valve to step 0 when the Active Test is completed.
Do not open the EGR valve 30 steps or more during the Active Test.
MAP change in response to EGR step position.
| - | EGR Step Position (Active Test) | |
|---|---|---|
| 0 Steps | 0 to 30 Steps | |
| MAP
(Data List) |
(EGR valve is fully closed) | MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed |
While performing the Active Test, if the increase in the value of MAP is small, the EGR valve assembly may be a malfunctioning.
Even if the EGR valve assembly is malfunctioning, rough idling or an increase in the value of MAP may occur while performing the Active Test. However, the amount that the value of MAP increases will be smaller than normal.
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
A
B
Remove the EGR valve assembly (See page Engine / Hybrid System>2ZR-FXE (EMISSION CONTROL)>EGR VALVE>REMOVAL).
Check if the EGR valve is stuck open.
EGR valve is tightly closed.
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
A
B
Check the intake system for vacuum leaks (See page Engine / Hybrid System>2ZR-FXE (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION).
No leaks in intake system.
OK
NG
Check the fuel pressure (See page Engine / Hybrid System>2ZR-FXE (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION).
OK
NG
OK
NG
OK
NG
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
The A/C switch and all accessory switches should be off.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position / All Data / MAP.
Check the MAP value in the Data List while performing the Active Test.
Do not leave the EGR valve open for 10 seconds or more during the Active Test.
Be sure to return the EGR valve to step 0 when the Active Test is completed.
Do not open the EGR valve 30 steps or more during the Active Test.
MAP change in response to EGR step position.
| - | EGR Step Position (Active Test) | |
|---|---|---|
| 0 Steps | 0 to 30 Steps | |
| MAP
(Data List) |
(EGR valve is fully closed) | MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed |
While performing the Active Test, if the increase in the value of MAP is small, the EGR valve assembly may be a malfunctioning.
Even if the EGR valve assembly is malfunctioning, rough idling or an increase in the value of MAP may occur while performing the Active Test. However, the amount that the value of MAP increases will be smaller than normal.
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
A
B
Remove the EGR valve assembly (See page Engine / Hybrid System>2ZR-FXE (EMISSION CONTROL)>EGR VALVE>REMOVAL).
Check if the EGR valve is stuck open.
EGR valve is tightly closed.
OK
NG
Inspect the spark plug of the misfiring cylinder (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION).
OK
NG
Perform a spark test (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION).
If the result of the spark test is normal, proceed to the next step.
NEXT
Measure the cylinder compression pressure of the misfiring cylinder (See page Engine / Hybrid System>2ZR-FXE (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION).
OK
NG
Disconnect the ECM connector.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D28-85 (#10) - D28-109 (E01) | Power switch on (IG) | 11 to 14 V |
| D28-84 (#20) - D28-109 (E01) | Power switch on (IG) | 11 to 14 V |
| D28-83 (#30) - D28-109 (E01) | Power switch on (IG) | 11 to 14 V |
| D28-82 (#40) - D28-109 (E01) | Power switch on (IG) | 11 to 14 V |
| *a | Front view of wire harness connector
(to ECM) |
OK
NG
Check the fuel injector assembly injection (whether fuel volume is high or low, and whether injection pattern is poor) (See page Engine / Hybrid System>2ZR-FXE (FUEL)>FUEL INJECTOR>INSPECTION).
OK
NG
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Clear the DTCs (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on (IG).
Turn the GTS on.
Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0300, P0301, P0302, P0303 or P0304.
Check the DTC judgment result.
| Result | Proceed to |
|---|---|
| ABNORMAL
(DTC P0300, P0301, P0302, P0303 and/or P0304 is output) |
A |
| NORMAL
(DTC is not output) |
B |
A
B
Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter sub-assembly and ECM (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).
Repair any problems.
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Clear the DTCs (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on (IG).
Turn the GTS on.
Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0300, P0301, P0302, P0303 or P0304.
Check the DTC judgment result.
| Result | Proceed to |
|---|---|
| ABNORMAL
(DTC P0300, P0301, P0302, P0303 and/or P0304 is output) |
A |
| NORMAL
(DTC is not output) |
B |
A
B
OK
NG
Replace the mass air flow meter sub-assembly (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>MASS AIR FLOW METER>REMOVAL).
If the results of the inspections performed in steps 13 and 21 indicated no problem, proceed to the next step without replacing the mass air flow meter sub-assembly.
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Clear the DTCs (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on (IG).
Turn the GTS on.
Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0300, P0301, P0302, P0303 or P0304.
Check the DTC judgment result.
| Result | Proceed to |
|---|---|
| NORMAL
(DTC is not output) |
A |
| ABNORMAL
(DTC P0300, P0301, P0302, P0303 and/or P0304 is output) |
B |
A
B
Check the fuel lines for leaks or blockage.
OK
NG