Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › FRAME WIRE
RM3210E _51 Engine / Hybrid System _047524 HYBRID / BATTERY CONTROL _0244771 FRAME WIRE A

HYBRID / BATTERY CONTROL  FRAME WIRE  INSTALLATION  


PROCEDURE

Hide 821H1 1.INSTALL HV FLOOR UNDER WIRE

CAUTION:

Wear insulated gloves.


a.
A371688C03
0.052,0.25 0.375,0.49 0.323,0.24 12 true *A 0.042,2.573 0.365,2.813 0.323,0.24 12 true *B 0.76,1.49 0.969,1.688 0.208,0.198 10 true A 0.938,3.74 1.146,3.938 0.208,0.198 10 true A 3.01,1.51 3.219,1.708 0.208,0.198 10 true B 2.885,3.875 3.094,4.073 0.208,0.198 10 true B
*A for LHD
*B for RHD


Engage the clamp (B).


b.

Install a new clamp (A).


c.
A378133

Insert the HV floor under wire into the floor panel hole and engage the grommet.


d.

Install 3 new clamps in the order shown in the illustration.

A371693N02
1.344,1.719 1.5,1.917 0.156,0.198 10 true 1 3.583,1.729 3.74,1.927 0.156,0.198 10 true 2 5.917,1.729 6.073,1.927 0.156,0.198 10 true 3


e.
A378131

Install the HV floor under wire with the 2 nuts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


Hide 46420 2.CONNECT NO. 2 PARKING BRAKE CABLE ASSEMBLY

a.

Connect the No. 2 parking brake cable assembly with the 2 bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 51201 3.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

Hide 58165B 4.INSTALL FRONT FLOOR COVER RH

HINT:

Perform the same procedure as for the front floor cover LH.

Click hereEngine / Hybrid System>2ZR-FXE INTAKE / EXHAUST>EXHAUST MANIFOLD>INSTALLATION


Hide 58390 5.INSTALL NO. 1 FLOOR UNDER COVER ASSEMBLY

Hide 821H1 6.CONNECT HV FLOOR UNDER WIRE

CAUTION:

Wear insulated gloves.


a.

Connect the shield ground to the HV battery.


b.

Connect the 2 HV battery junction block assembly connectors.

NOTICE:

Make sure that the connectors are connected securely.



Hide G92N4A 7.INSTALL NO. 1 HV BATTERY COVER PANEL RH

Hide 71033 8.INSTALL REAR SEAT CUSHION LEG SUB-ASSEMBLY

Hide 76974F 10.INSTALL REAR UNDER SIDE COVER LH

Hide 67918A 11.INSTALL REAR DOOR SCUFF PLATE LH

Hide 76973F 12.INSTALL REAR UNDER SIDE COVER RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION


Hide 67917A 13.INSTALL REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION


Hide 72693 14.INSTALL REAR SEAT CUSHION LOCK HOOK

Hide 15.INSTALL REAR SEAT CUSHION ASSEMBLY

Hide 82121 17.CONNECT ENGINE WIRE

CAUTION:

Wear insulated gloves.


NOTICE:

Do not allow any foreign matter or water to enter the inverter with converter assembly.


a.

Engage the 2 clamps and connect the engine wire.


b.

Install the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


c.
A376381

Connect the 2 inverter with converter assembly connectors and move each lock lever as shown in the illustration.

NOTICE:
·

To prevent damage due to static electricity, do not touch the terminals of the disconnected connectors.

·

Do not damage the terminals, connector housing or inverter with converter assembly when connecting the connectors.

·

Do not touch the waterproof seal or terminals of the connector.




Hide 12601B 18.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 55701J 19.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 55736D 20.INSTALL COWL BODY MOUNTING REINFORCEMENT LH

Hide 55735A 21.INSTALL WATER GUARD PLATE LH

Hide 55737B 22.INSTALL NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL (for LHD)

Hide 55738D 23.INSTALL NO. 2 HEATER AIR DUCT SPLASH SHIELD SEAL (for RHD)

Hide 24.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY