Home › Engine / Hybrid System › 2ZR-FXE ENGINE MECHANICAL › CYLINDER HEAD GASKET
RM3210E _51 Engine / Hybrid System _047495 2ZR-FXE ENGINE MECHANICAL _0244903 CYLINDER HEAD GASKET A

2ZR-FXE ENGINE MECHANICAL  CYLINDER HEAD GASKET  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during cylinder head gasket removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Intelligent clearance sonar system*1
Simple intelligent parking assist system*1
Pre-crash safety system
Parking assist monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)
Replacement of inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


(Click here)
for SFI system (w/ Canister Pump Module)

Replacement of ECM


Perform Vehicle Identification Number (VIN) registration MIL comes on (Click here)
for SFI system (w/o Canister Pump Module)

Replacement of ECM


Perform Vehicle Identification Number (VIN) or frame number registration (Click here)
for SFI system (w/ Canister Pump Module)
·

Replacement of throttle body assembly

·

Replacement of cylinder head sub-assembly

·

Replacement of camshaft (for intake or exhaust camshaft)

·

Replacement of camshaft timing gear assembly

·

Replacement of fuel injector assembly

·

Replacement of ignition coil assembly

·

Replacement of EGR valve assembly

·

Gas leak from exhaust system is repaired


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
for SFI system (w/o Canister Pump Module)
·

Replacement of throttle body assembly

·

Replacement of cylinder head sub-assembly

·

Replacement of camshaft (for intake or exhaust camshaft)

·

Replacement of camshaft timing gear assembly

·

Replacement of fuel injector assembly

·

Replacement of ignition coil assembly

·

Replacement of EGR valve assembly

·

Gas leak from exhaust system is repaired


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

Intelligent clearance sonar system

·

Simple advanced parking guidance system


(Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
Initialize No. 1 headlight ECU sub-assembly LH Automatic headlight beam level control system (Click here)
Front wheel alignment adjustment
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light/yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Replacement of hybrid vehicle transaxle assembly
·

Resolver learning

·

Initialize resolver


·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


(Click here)

*1: When performing learning using the GTS.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT CLEARANCE SONAR SYSTEM>CALIBRATION

PROCEDURE

Hide 16331 3.REMOVE WATER OUTLET (w/ Flow Shutting Valve (Water Valve))

Hide 16331 4.REMOVE WATER OUTLET (w/o Flow Shutting Valve (Water Valve))

Hide 25620 6.REMOVE EGR VALVE ASSEMBLY WITH EGR COOLER

Hide 17167 7.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 17141 9.REMOVE EXHAUST MANIFOLD (TWC: Front Catalyst)

Hide 15301 11.REMOVE ENGINE OIL LEVEL DIPSTICK

Hide 11452 12.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 16289 13.REMOVE NO. 5 WATER BY-PASS PIPE (w/ Exhaust Heat Recirculation System)

Hide 1628A 14.REMOVE NO. 6 WATER BY-PASS PIPE

Hide 17650G 15.REMOVE PURGE VALVE (PURGE VSV)

Hide 23818 16.REMOVE FUEL VAPOR FEED PIPE

Hide 23807 17.REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

Hide 23807V 18.REMOVE NO. 1 DELIVERY PIPE SPACER

Hide 23250 19.REMOVE FUEL INJECTOR ASSEMBLY

Hide 11101E 21.REMOVE CAMSHAFT POSITION SENSOR

Hide 11201 22.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 11213 23.REMOVE CYLINDER HEAD COVER GASKET

Hide 11193 24.REMOVE SPARK PLUG TUBE GASKET

Hide 25.SET NO. 1 CYLINDER TO TDC (COMPRESSION)

Hide 13540 27.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 11302A 28.REMOVE TIMING CHAIN COVER OIL SEAL

Hide 11302 29.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

Hide 13559 30.REMOVE CHAIN TENSIONER SLIPPER

Hide 13561 31.REMOVE NO. 1 CHAIN VIBRATION DAMPER

Hide 13562 32.REMOVE NO. 2 CHAIN VIBRATION DAMPER

Hide 13506 33.REMOVE CHAIN SUB-ASSEMBLY

a.
A374439C01
2.823,2.406 2.958,1.75 true 1.75,4.073 0.594,3.813 true 1.823,4.031 2.135,4.188 0.313,0.156 10 true *a 2.958,1.615 3.271,1.771 0.313,0.156 10 false *b
*a Loosen the chain sub-assembly
*b Place the chain sub-assembly on the non-toothed portion of camshaft timing gear assembly


Using a wrench to hold the hexagonal portion of the camshaft, turn the camshaft timing gear assembly counterclockwise to loosen the chain sub-assembly between the camshaft timing sprocket and camshaft timing gear assembly.


b.

With the chain sub-assembly loosened, separate the chain sub-assembly from the teeth of the camshaft timing gear assembly and place it on the non-toothed portion of camshaft timing gear assembly.


c.

Turn the camshaft clockwise to return it to its original position and remove the chain sub-assembly.


Hide 13050 34.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

Hide 13050 35.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

Hide 13523G 36.REMOVE CAMSHAFT TIMING SPROCKET

Hide 11103 40.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY

Hide 13801 41.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Hide 13750 42.REMOVE VALVE LASH ADJUSTER ASSEMBLY

Hide 11101 44.REMOVE CYLINDER HEAD SUB-ASSEMBLY

Hide 11115 45.REMOVE CYLINDER HEAD GASKET

a.
A374457

Remove the cylinder head gasket from the cylinder block sub-assembly.


Hide 11101A 46.INSPECT CYLINDER HEAD SET BOLT