2005-2008 RAV4 · Service Manual BRAKE

Downhill Assist Control Indicator Light does not Come ON

Circuit diagnosis · Vehicles built from Aug 2008

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 Aug 2007 – Jul 2008 from Aug 2008

DESCRIPTION

Refer to the description of "Downhill Assist Control Indicator Light Remains ON" (Click here).

WIRING DIAGRAM

Refer to the downhill assist control indicator light circuit (Click here).

INSPECTION PROCEDURE

NOTICE:
When replacing the brake actuator assembly, perform zero point calibration (Click here).


1. CHECK CAN COMMUNICATION SYSTEM
  1. Check if a CAN communication system DTC is output (Click here)

Result:
Result
Proceed to
DTC is not output.
A
DTC is output.
B



B
REPAIR CAN COMMUNICATION SYSTEM (Click here)
A


2. READ VALUE USING INTELLIGENT TESTER (DOWNHILL ASSIST CONTROL SWITCH)
  1. Check the Data List for proper functioning of the downhill assist control switch.

    ABS/VSC/TRC: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Downhill Assist Control Switch
    Downhill assist control switch / ON or OFF
    ON: Downhill assist control switch is on
    OFF: Downhill assist control switch is off
    -

    OK:
    ON (downhill assist control switch is on) appears on the screen.



NG
Go to step 5
OK


3. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (DOWNHILL ASSIST CONTROL INDICATOR LIGHT)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Select the Active Test mode on the intelligent tester (Click here).

    ABS/VSC/TRC: 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Downhill Assist Control Indicator Light
    Downhill assist control indicator light
    Indicator light ON / OFF
    Observe the combination meter.

    OK:
    The downhill assist control indicator light turns ON and OFF.



OK
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
NG


4. INSPECT COMBINATION METER ASSEMBLY
  1. Inspect the combination meter (Click here).



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)

5. INSPECT DOWNHILL ASSIST CONTROL SWITCH
C128533E07
  1. Remove the downhill assist control switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    4 - 1
    Switch is pushed
    Below 1 Ω
    Switch is not pushed
    10 kΩ or higher



NG
REPLACE DOWNHILL ASSIST CONTROL SWITCH
OK


6. CHECK HARNESS AND CONNECTOR (DOWNHILL ASSIST CONTROL SW - SKID CONTROL ECU/BODY GROUND)
C194144E03
  1. Disconnect the skid control ECU connector.

  1. Disconnect the downhill assist control switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A67-29 (HDCS) - E36-4
    Always
    Below 1 Ω
    A67-29 (HDCS) - Body ground
    Always
    10 kΩ or higher
    E36-1 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)


← Downhill Assist Control Indicator Light does not Come ON (Aug 2007 – Jul 2008)AUTO LSD Indicator Light Remains ON (from Aug 2008) →