ECD SYSTEM (for CCo) > Black Smoke Emitted |
| Faults and Symptoms of Common Rail Diesel Components |
Engine Control
| Component | Intake system | |
| Symptom: Main fault |
| |
| Data List |
| |
| Component | Turbocharger system | |
| Main fault |
| |
| Symptoms | Lack of power (when vehicle starting, when heavy load) (Black smoke is not emitted when racing while vehicle stopped) | |
| Data List | MAP (inside intake air pressure), Target Booster Pressure
| |
| Component | Glow system | |
| Main fault | Open circuit, glow plug relay fault | |
| Symptoms | Difficult to start, rough idle, knocking, white smoke (when cold) | |
| Data List | Check the glow plug indicator light | |
| Diagnostic Point | Try to measure the resistance of the glow plug | |
| Component | Engine | |
| Main fault | Loss of compression | |
| Symptoms | Rough idle (lack of power always) | |
| Data List | Engine Speed of Cyl
| |
Diesel Injection
| Component | Fuel supply pump | |
| Main fault | - | |
| Symptoms | Difficult to start, engine stalling, rough idle, lack of power | |
| Data List | Fuel Press, Target Common Rail Pressure, Target Pump SCV Current
| |
| Diagnostic Trouble Code | Even if Fuel Press is less than Target Common Rail Pressure, a DTC will not be stored. | |
| Component | Fuel injector | |
| Main fault | Blockage | |
| Symptoms | Rough idle, lack of power, black smoke, white smoke, knocking | |
| Data List | Injection Feedback Val
| |
| Component | Injector Driver (EDU) | |
| Main fault | Circuit fault: The fuel injector does not open. | |
| Symptoms | Difficult to start, rough idle, lack of power, black smoke, white smoke, knocking | |
| Data List | Same as fuel injector | |
| Diagnostic Trouble Code | When the EDU has a fault, some DTCs may be stored. | |
| Component | Fuel pressure sensor | |
| Main fault | Open circuit, decrease in performance (foreign matter is stuck) | |
| Symptoms | Difficult to start, rough idle, engine stall, lack of power | |
| Data List | Fuel Press, Target Common Rail Pressure
| |
| Diagnostic Trouble Code | When the fuel pressure sensor has a fault, some DTCs may be stored. | |
| Component | Irregular fuel | |
| Main fault | - | |
| Symptoms | Difficult to start, rough idle (especially when cold) | |
Diesel EGR
| Component | EGR system | |
| Main fault |
| |
| Symptoms |
| |
| Data List | Actual EGR Valve Pos., Target EGR Pos.
| |
Diesel Throttle
| Component | Diesel throttle system | |
| Main fault | Stuck, does not move smoothly | |
| Symptoms |
| |
| Data List |
| |
| Data List Related to Black Smoke |
Engine Control
| Data List | Judgment of Data List Values | Faulty Component | Diagnosis Note |
| Engine Speed | Idling: 750 to 850 rpm | Crankshaft position sensor | When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 or varies greatly from the actual engine speed. |
| Data List | Judgment of Data List Values | Faulty Component | Diagnosis Note |
| MAP |
| When MAP is low, the following conditions are possible:
|
|
Results of real-vehicle check:
| |||
| Data List | Judgment of Data List Values | Faulty Component | Diagnosis Note |
| MAF | - |
|
|
Results of real-vehicle check:
| |||
| |||
| Data List | Judgment of Data List Values | Faulty Component | Diagnosis Note |
| Intake Air | - | Intake air temperature sensor. |
|
| Data List | Judgment of Data List Values | Faulty Component | Diagnosis Note |
| Coolant Temp |
| Engine coolant temperature sensor |
|
| Data List | Judgment of Data List Values | Faulty Component | Diagnosis Note |
| Engine Speed of Cyl #1 (to #4) | When cranking, the engine speed of each cylinder is the same under normal conditions. When a cylinder is approximately 100 rpm higher than the other cylinders, it is conceivable that the compression of that cylinder is being lost.
| - |
|
Diesel Injection
| Data List | Judgment of Data List Values | Faulty Component | Diagnosis Note |
| Target Common Rail Pressure | - | - |
|
Results of real-vehicle check:
| |||
| Data List | Judgment of Data List Values | Faulty Component | Diagnosis Note |
| Fuel Press |
|
|
|
Results of real-vehicle check:
| |||
| Data List | Judgment of Data List Values | Faulty Component | Diagnosis Note |
| Target Pump SCV Current | Idling after warming up: roughly 923 to 1123 mA. When this value is large, the pump is trying to increase the fuel discharge rate. |
|
|
Results of real-vehicle check:
| |||
| Data List | Judgment of Data List Values | Faulty Component | Diagnosis Note |
| Injection Feedback Val #1 (to #4) |
|
|
|
| Data List | Judgment of Data List Values | Faulty Component | Diagnosis Note |
| Injection Volume | - | - | After warming up the engine, when Injection Volume during idling is 10 mm3/st or more, there is tendency for the injector to clog. |
Results of real-vehicle check:
| |||
Diesel Throttle
| Data List | Judgment of Data List Values | Faulty Component | Diagnosis Note |
| Actual Throttle Position |
| Diesel throttle body | Actual Throttle Position is the closing percentage of the throttle valve.
|
Results of real-vehicle check:
| |||
Diesel EGR
| Data List | Judgment of Data List Values | Faulty Component | Diagnosis Note |
| Target EGR Position | - | - |
|
Results of real-vehicle check:
| |||
| Data List | Judgment of Data List Values | Faulty Component | Diagnosis Note |
| Actual EGR Valve Pos. |
| EGR valve assembly |
|
Results of real-vehicle check:
| |||
| Data List | Judgment of Data List Values | Faulty Component | Diagnosis Note |
| EGR Close Lrn. Status |
| - | After disconnecting and reconnecting the battery cable, if the ignition switch has not been turned off once, learning may not be completed. |
| Data List | Judgment of Data List Values | Faulty Component | Diagnosis Note |
| EGR Close Lrn. Val. | When leaving the vehicle idling, with the EGR Close Lrn. Status OK, the normal range of EGR Close Lrn. Val. is within 0.34 to 0.70 V. In cases when EGR Close Lrn. Status is NG or EGR Close Lrn. Val. is at the maximum or minimum (0.34 to 0.70 V) of the normal range, it is possible that the EGR valve is not completely closed or a foreign object is lodged in the EGR valve seat area. | - |
|
| Explanation of Symptom |
| Black Smoke | The fuel used in diesel engines has a higher boiling point and evaporates much slower than that used in gasoline engines. Additionally, the fuel is injected directly, so the air fuel mixture in diesel engines is formed in a very short period of time and is less homogenous. This is why diesel engines must operate with excess air fuel ratio across the entire operating range. An insufficient quantity of air, results in imperfect combustion and increased particulate (soot) emission. When the accelerator pedal is depressed, a lot of fuel is injected. As a result, the air fuel ratio becomes rich. In this relatively rich environment, fuel droplets lacking in oxygen burn imperfectly producing soot, which is emitted as black smoke. In order to prevent black smoke production, the maximum injection quantity for a given intake air mass is limited (final injection quantity is limited by MAF). Black smoke is emitted either when:
|
| 1.READ OUTPUT DTC (RELATING TO ENGINE) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read pending DTCs.
| Result | Proceed to |
| No DTCs are output | A |
| Engine related DTCs are output | B |
|
| ||||
| A | |
| 2.CHECK WIRE HARNESS AND CONNECTION IN ENGINE COMPARTMENT |
Check the wire harness and connector connections of common rail system components.
|
| ||||
| OK | |
| 3.TAKE SNAPSHOT DURING IDLING AND 3000 RPM |
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.
Take a snapshot of the following Data List items.
| Data List | Value | Unit |
| Engine Speed | 771 | rpm |
| MAP | 94 | kPa |
| MAF | 3.84 | g/sec |
| Target Common Rail Pressure | 35000 | kPa |
| Fuel Press | 33640 | kPa |
| Injection Volume | 5.15 | mm3/st |
| VN Turbo Command | 57 | % |
| Target EGR Position | 54.1 | % |
| Actual EGR Valve Pos. | 54.1 | % |
| EGR Close Lrn. Val. | 0.52 | V |
| EGR Close Lrn. Status | OK | - |
| Actual Throttle Position | 93 | % |
| Throttle Close Learning Val. | 16.9 | deg |
| Diesel Throttle Learn Status | OK | - |
| Accel Position | 0.00 | % |
| Injection Feedback Val #1 | 0.0 | mm3/st |
| Injection Feedback Val #2 | -0.5 | mm3/st |
| Injection Feedback Val #3 | 0.0 | mm3/st |
| Injection Feedback Val #4 | 0.1 | mm3/st |
| Atmosphere Pressure | 100 | kPa |
| Coolant Temp | 76 | °C |
| Calculate Load | 14.5 | % |
| Pilot 1 Injection Period | 208 | μs |
| Pilot 2 Injection Period | 213 | μs |
| Data List | Value | Unit |
| Engine Speed | 3000 | rpm |
| Target Booster Pressure | 115.46 | kPa |
| MAP | 121 | kPa |
| MAF | 52.51 | g/sec |
| Target Common Rail Pressure | 67500 | kPa |
| Fuel Press | 67460 | kPa |
| Target Pump SCV Current | 1039.0 | mA |
| Injection Volume | 8.73 | mm3/st |
| VN Turbo Command | 62 | % |
| Target EGR Position | 42.3 | % |
| Actual EGR Valve Pos. | 42.3 | % |
| EGR Close Lrn. Val. | 0.52 | V |
| EGR Close Lrn. Status | OK | - |
| Actual Throttle Position | 40 | % |
| Throttle Close Learning Val. | 16.9 | deg |
| Diesel Throttle Learn Status | OK | - |
| Accel Position | 14.06 | % |
| Injection Feedback Val #1 | 0.0 | mm3/st |
| Injection Feedback Val #2 | -0.5 | mm3/st |
| Injection Feedback Val #3 | 0.1 | mm3/st |
| Injection Feedback Val #4 | 0.0 | mm3/st |
| Coolant Temp | 83 | °C |
| Calculate Load | 20.7 | % |
| Pilot 1 Injection Period | 163 | μs |
| Pilot 2 Injection Period | 182 | μs |
| NEXT | |
| 4.CHECK SNAPSHOT (TARGET PUMP SCV CURRENT) |
![]() |
Check Target Pump SCV Current in the snapshot taken when the engine was idling and at 3000 rpm with no load.
| Result | Proceed to |
| Target Pump SCV Current is below 3000 mA | A |
| Target Pump SCV Current is 3000 mA or higher | B |
|
| ||||
| A | |
| 5.CHECK FUEL INJECTOR COMPENSATION CODE |
Read the fuel injector compensation codes.
|
| ||||
| OK | |
| 6.CHECK SNAPSHOT (INJECTION FEEDBACK VAL #1 to #4) |
Check Injection Feedback Val # and Injection Volume in the snapshot taken after the engine is warmed up and has been idling for 1 minute.
| Result | Proceed to |
| Injection Feedback Val #1 to #4 is within the range of +/-3 mm3/st and Injection Volume is 10 mm3/st or less | A |
| Injection Feedback Val #1 to #4 is within the range of +/-3 mm3/st and Injection Volume is more than 10 mm3/st | B* |
Injection Feedback Val #1 to #4 is outside the range of +/-3 mm3/st
| C |
|
| ||||
|
| ||||
| A | |
| 7.CHECK EGR VALVE ASSEMBLY |
Check the EGR valve assembly .
|
| ||||
| OK | |
| 8.INSPECT ENGINE COOLANT TEMPERATURE SENSOR |
Inspect the engine coolant temperature sensor (Click here).
|
| ||||
| OK | |
| 9.READ VALUE USING INTELLIGENT TESTER (MAP AND ATMOSPHERE PRESSURE) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / MAP and Atmosphere Pressure.
Compare MAP to Atmosphere Pressure when the ignition switch is ON (engine stopped).
| Result | Proceed to |
| Atmosphere Pressure is different from actual atmospheric pressure | A |
| MAP is different from actual atmospheric pressure | B |
| MAP and Atmosphere Pressure have the same value | C |
|
| ||||
|
| ||||
| C | |
| 10.READ VALUE USING INTELLIGENT TESTER (ACCEL POSITION) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Position.
Read the value.
| Condition | Standard Value |
| Accelerator pedal released | 0% |
| Accelerator pedal depressed | 100% |
Accelerator pedal released → depressed
| 0 to 100% |
|
| ||||
| OK | |
| 11.READ VALUE USING INTELLIGENT TESTER (INTAKE AIR AND INTAKE AIR TEMP (TURBO)) |
Connect the intelligent tester to the DLC3.
Soak the engine for a long time.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air, Intake Air Temp (Turbo).
|
| ||||
| OK | |
| 12.TAKE SNAPSHOT WHILE ACCELERATING WITH ACCELERATOR FULLY OPEN |
![]() |
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.
Take a snapshot of the following Data List items.




| Data List | Value | Unit |
| Vehicle Speed | 44 | km/h |
| Engine Speed | 3500 | rpm |
| Accel Position | 99.60 | % |
| Target Booster Pressure | 234.19 | kPa |
| MAP | 227 | kPa |
| MAF | 140.96 | g/sec |
| Calculate Load | 100.0 | % |
| Target Common Rail Pressure | 194350 | kPa |
| Fuel Press | 189820 | kPa |
| Target Pump SCV Current | 1402.8 | mA |
| Injection Volume | 70.52 | mm3/st |
| VN Turbo Command | 44 | % |
| Actual EGR Valve Pos. | 0 | % |
| Actual Throttle Position | 0 | % |
| NEXT | |
| 13.CHECK SNAPSHOT (MAP AND TARGET BOOSTER PRESSURE) |
Check the condition of the vehicle using the snapshot.
| Result | Proceed to |
| MAP is less than "Target Booster Pressure - 20 kPa" when accelerating with accelerator fully open | A |
| MAP and Target Booster Pressure values are almost the same | B |
|
| ||||
| A | |
| 14.INSPECT VACUUM HOSE |
Check the vacuum hose connection (manifold absolute pressure sensor).
|
| ||||
| OK | |
| 15.CHECK INTAKE SYSTEM |
Check for air leakage between the turbocharger and intake manifold.
Check for air leakage at intake manifold.

|
| ||||
| OK | |
| 16.CHECK TURBOCHARGER SUB-ASSEMBLY (MECHANICAL PROBLEM) |
Check the turbocharger sub-assembly .
|
| ||||
| OK | |
| 17.PERFORM ENGINE SPEED ACCELERATION (CHECK FOR BLACK SMOKE) |
Start the engine and drive the vehicle until the engine coolant temperature reaches 60°C (140°F) or higher.
Stop the vehicle and allow the engine to idle.
Fully depress the accelerator pedal for 5 seconds and then release it.*1
Repeat the above procedure *1 10 times.*2
Check for black smoke emission during procedures *1 and *2.
|
| ||||
| OK | ||
| ||
| 18.BASIC INSPECTION |
Check the fuel quality.
Check the fuel for air.
Check the fuel system for blockages.
Check the air filter.
Check the engine oil.
Check the engine coolant.
Check the engine idling speed and maximum engine speed.
Check the vacuum pump.
|
| ||||
| OK | |
| 19.REPLACE CATALYTIC CONVERTER |
Replace the catalytic converter (Click here).
| NEXT | |
| 20.CHECK INTAKE SYSTEM DEPOSIT |
Check carbon has accumulated on the intake manifold, cylinder head, etc. and if so, clean it off.
| NEXT | |
| 21.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
| NEXT | ||
| ||
| 22.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM) |
![]() |
Disconnect the suction control valve connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B46-1 (+B) - B32-41 (PCV+) | Always | Below 1 Ω |
| B46-2 (PCV) - B32-81 (PCV-) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| B46-1 (+B) or B32-41 (PCV+) - Body ground | Always | 10 kΩ or higher |
| B46-2 (PCV) or B32-81 (PCV-) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Suction Control Valve) |
| *2 | Front view of wire harness connector (to ECM) |
Reconnect the suction control valve connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 23.CHECK IF FUEL IS BEING SUPPLIED TO FUEL SUPPLY PUMP |
Disconnect the inlet hose from the fuel supply pump.
Operate the priming pump and check that fuel is being supplied to the fuel supply pump.
|
| ||||
| OK | |
| 24.REPLACE SUPPLY PUMP |
Replace the supply pump (Click here).
| NEXT | |
| 25.BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system .
| NEXT | |
| 26.PERFORM FUEL SUPPLY PUMP INITIALIZATION |
Perform supply pump initialization (Click here).
| NEXT | |
| 27.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
| NEXT | ||
| ||
| 28.REPLACE FUEL INJECTOR OF ALL CYLINDERS |
Replace the fuel injectors (Click here).
| NEXT | |
| 29.BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system .
| NEXT | |
| 30.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING |
Register the injector compensation codes .
Perform the fuel injector pilot quantity learning .
| NEXT | |
| 31.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
| NEXT | ||
| ||
| 32.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE CYLINDER #1 TO #4 FUEL CUT) |
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Cylinder #1 to #4 Fuel Cut.
| NEXT | |
| 33.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CHECK THE CYLINDER COMPRESSION) |
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Check the Cylinder Compression / Data List / Compression / Engine Speed of Cyl #1 to #4.
Check the engine speed during the Active Test.
| Result | Proceed to |
| Except below | A |
| The values of Engine Speed Cyl #1 to #4 are within +/-10 rpm of each other. | B |
|
| ||||
| A | |
| 34.CHECK CYLINDER COMPRESSION PRESSURE OF MALFUNCTIONING CYLINDER |
Check cylinder compression pressure .
|
| ||||
| OK | |
| 35.REPLACE FUEL INJECTOR OF MALFUNCTIONING CYLINDER |
Replace the fuel injector of the malfunctioning cylinder (Click here).
| NEXT | |
| 36.BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system .
| NEXT | |
| 37.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING |
Register the injector compensation code .
Perform the fuel injector pilot quantity learning .
| NEXT | |
| 38.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
| NEXT | ||
| ||
| 39.CHECK AND REPLACE CLOGGED FUEL PIPE (INCLUDING FUEL FREEZING) (FUEL TANK - FUEL SUPPLY PUMP) |
Check and replace clogged the fuel pipe.
| NEXT | |
| 40.BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system .
| NEXT | |
| 41.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
| NEXT | ||
| ||