There may be a short circuit between the CAN bus lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 53 Ω.
| Symptom | Trouble Area |
|---|---|
|
*1: w/ Blind Spot Monitor System *2: w/ Lane Departure Alert System *3: for Radio and Display Type *4: for AWD *5: w/ Smart Key System *6: for 2 Pin Connector Type *7: for 22 Pin Connector Type |
|
| The resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 53 Ω. | ·
Short between CAN bus lines ·
ECM ·
Blind spot monitor sensor LH*1 ·
Brake actuator assembly (skid control ECU) ·
Power steering ECU assembly ·
Main body ECU (multiplex network body ECU) ·
Lane departure warning camera*2 ·
Air conditioning amplifier assembly ·
Radio and display receiver assembly*3 ·
4WD ECU assembly*4 ·
Certification ECU (smart key ECU assembly)*5 ·
Spiral with sensor cable sub-assembly (steering angle sensor) ·
Airbag sensor assembly ·
Combination meter assembly ·
No. 1 CAN junction connector*6 ·
No. 2 CAN junction connector*6 ·
No. 3 CAN junction connector*6 ·
No. 4 CAN junction connector*7 ·
No. 21 CAN junction connector*7 ·
DLC3 CAN branch wire or connector |
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Click here
The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the Precaution in the SRS.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.
Check vehicles type.
| Proceed to |
|---|
| for 2 Pin Connector Type |
| for 22 Pin Connector Type |
for 2 Pin Connector Type
for 22 Pin Connector Type
| *a | Front view of DLC3 |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the G124 No. 1 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G14-6 (CANH) - G14-14 (CANL) | Cable disconnected from negative (-) battery terminal | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the No. 1 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of DLC3 |
Disconnect the N28 No. 3 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G14-6 (CANH) - G14-14 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the No. 3 CAN junction connectors.
| *1 | No. 3 CAN Junction Connector | - | - |
| *a | Rear view of wire harness connector
(to No. 3 CAN Junction Connector) |
- | - |
| Code | Color (CANH Side) | Color (CANL Side) | Connect to |
|---|---|---|---|
|
*: w/ Blind Spot Monitor System |
|||
| N27 | Y | W | ECM |
| N29 | R | W | Blind Spot Monitor Sensor LH* |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N27-1 (CANH) - N27-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| N29-1 (CANH) - N29-2 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG (to ECM CAN main wire) |
| NG (to blind spot monitor sensor LH CAN branch wire) |
OK
NG (to ECM CAN main wire)
NG (to blind spot monitor sensor LH CAN branch wire)
Reconnect all wire harness No. 3 CAN junction connectors.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to ECM) |
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A62-13 (CANH) - A62-26 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect all wire harness No. 3 CAN junction connectors.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to Blind Spot Monitor Sensor LH) |
Disconnect the blind spot monitor sensor LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R1-2 (CA1P) - R1-7 (CA1N) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the No. 3 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the No. 1 CAN junction connector.
| *1 | No. 1 CAN Junction Connector | - | - |
| *a | Rear view of wire harness connector
(to No. 1 CAN Junction Connector) |
- | - |
| Code | Color (CANH Side) | Color (CANL Side) | Connect to |
|---|---|---|---|
| G118 | L | W | No. 3 CAN Junction Connector |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G118-1 (CANH) - G118-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the No. 1 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of DLC3 |
Disconnect the G129 No. 2 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G14-6 (CANH) - G14-14 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the No. 2 CAN junction connectors.
| *1 | No. 2 CAN Junction Connector | - | - |
| *a | Rear view of wire harness connector
(to No. 2 CAN Junction Connector) |
- | - |
| Code | Color (CANH Side) | Color (CANL Side) | Connect to |
|---|---|---|---|
|
*1: for Radio and Display Type *2: for AWD *3: w/ Smart Key System |
|||
| G126 | B | W | Air Conditioning Amplifier Assembly |
| G128 | G | W | Combination Meter Assembly |
| G130 | Y | W | Radio and Display Receiver Assembly*1 |
| G131 | L | W | 4WD ECU Assembly*2 |
| G132 | R | W | Certification ECU (Smart Key ECU Assembly)*3 |
| G133 | BR | W | Airbag Sensor Assembly |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G126-1 (CANH) - G126-2 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G128-1 (CANH) - G128-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| G130-1 (CANH) - G130-2 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G131-1 (CANH) - G131-2 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G132-1 (CANH) - G132-2 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G133-1 (CANH) - G133-2 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to air conditioning amplifier assembly CAN branch wire) | B |
| NG (to combination meter assembly CAN main wire) | C |
| NG (to radio and display receiver assembly CAN branch wire) | D |
| NG (to 4WD ECU assembly CAN branch wire) | E |
| NG (to certification ECU [smart key ECU assembly] CAN branch wire) | F |
| NG (to airbag sensor assembly CAN branch wire) | G |
A
B
C
D
E
F
G
Reconnect all wire harness No. 2 CAN junction connectors.
| Proceed to |
|---|
| NEXT |
NEXT
| *A | for Automatic Air Conditioning System |
| *B | for Manual Air Conditioning System |
| *a | Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly) |
Disconnect the air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G81-11 (CANH) - G81-12 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G80-8 (CANH) - G80-9 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect all wire harness No. 2 CAN junction connectors.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Rear view of wire harness connector
(to Combination Meter Assembly) |
Disconnect the combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G16-32 (CANH) - G16-31 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect all wire harness No. 2 CAN junction connectors.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to Radio and Display Receiver Assembly) |
Disconnect the radio and display receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G143-9 (CANH) - G143-10 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect all wire harness No. 2 CAN junction connectors.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Rear view of wire harness connector
(to 4WD ECU Assembly) |
Disconnect the 4WD ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G86-6 (CANH) - G86-5 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect all wire harness No. 2 CAN junction connectors.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to Certification ECU [Smart Key ECU Assembly]) |
Disconnect the certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G84-14 (CANH) - G84-15 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect all wire harness No. 2 CAN junction connectors.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Rear view of wire harness connector
(to Airbag Sensor Assembly) |
Disconnect the airbag sensor assembly connector.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G92-13 (CANH) - G92-22 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the No. 2 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the No. 1 CAN junction connectors.
| *1 | No. 1 CAN Junction Connector | - | - |
| *a | Rear view of wire harness connector
(to No. 1 CAN Junction Connector) |
- | - |
| Code | Color (CANH Side) | Color (CANL Side) | Connect to |
|---|---|---|---|
|
*: w/ Lane Departure Alert System |
|||
| G119 | V | W | No. 2 CAN Junction Connector |
| G120 | R | W | Brake Actuator Assembly (Skid Control ECU) |
| G121 | LG | W | Power Steering ECU Assembly |
| G122 | P | W | Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor) |
| G123 | Y | W | Main Body ECU (Multiplex Network Body ECU) |
| G125 | G | W | Lane Departure Warning Camera* |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G119-1 (CANH) - G119-2 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| G120-1 (CANH) - G120-2 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G121-1 (CANH) - G121-2 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G122-1 (CANH) - G122-2 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G123-1 (CANH) - G123-2 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G125-1 (CANH) - G125-2 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to brake actuator assembly [skid control ECU] CAN branch wire) | B |
| NG (to power steering ECU assembly CAN branch wire) | C |
| NG (to spiral with sensor cable sub-assembly [steering angle sensor] CAN branch wire) | D |
| NG (to main body ECU [multiplex network body ECU] CAN branch wire) | E |
| NG (to lane departure warning camera CAN branch wire) | F |
| NG (to No. 2 CAN junction connector CAN main wire) | G |
A
B
C
D
E
F
G
Reconnect all wire harness No. 1 CAN junction connectors.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU]) |
Disconnect the brake actuator assembly (skid control ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A64-25 (CANH) - A64-14 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect all wire harness No. 1 CAN junction connectors.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Rear view of wire harness connector
(to Power Steering ECU Assembly) |
Disconnect the power steering ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| h1-4 (CANH) - h1-8 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect all wire harness No. 1 CAN junction connectors.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to Spiral with Sensor Cable Sub-assembly [Steering Angle Sensor]) |
Disconnect the spiral with sensor cable sub-assembly (steering angle sensor) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G12-3 (CANH) - G12-2 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect all wire harness No. 1 CAN junction connectors.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Rear view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU]) |
Disconnect the main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G78-14 (CANH) - G78-13 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect all wire harness No. 1 CAN junction connectors.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to Lane Departure Warning Camera) |
Disconnect the lane departure warning camera connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Q13-6 (CA1P) - Q13-12 (CA1N) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of DLC3 |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the G134 No. 4 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G14-6 (CANH) - G14-14 (CANL) | Cable disconnected from negative (-) battery terminal | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the No. 4 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of DLC3 |
Disconnect the A72 No. 21 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G14-6 (CANH) - G14-14 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Rear view of wire harness connector
(to No. 21 CAN Junction Connector) |
| *b | to Brake Actuator Assembly (Skid Control ECU) |
| *c | to ECM |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A72-1 (CANH) - A72-12 (CANL) | Cable disconnected from negative (-) battery terminal | 200 or higher |
| A72-2 (CANH) - A72-13 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to brake actuator assembly [skid control ECU] CAN branch wire) | B |
| NG (to ECM CAN main wire) | C |
A
B
C
Reconnect the No. 21 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
Reconnect the No. 21 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
Reconnect the No. 21 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Rear view of wire harness connector
(to No. 4 CAN Junction Connector) |
| *b | to Airbag Sensor Assembly |
| *c | to Air Conditioning Amplifier Assembly |
| *d | to Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor) |
| *e | to Power Steering ECU Assembly |
| *f | to Main Body ECU (Multiplex Network Body ECU) |
| *g | to 4WD ECU Assembly |
| *h | to Combination Meter Assembly |
| *i | to No. 21 CAN Junction Connector |
Disconnect the No. 4 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G134-1 (CANH) - G134-12 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G134-2 (CANH) - G134-13 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G134-3 (CANH) - G134-14 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G134-4 (CANH) - G134-15 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G134-5 (CANH) - G134-16 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G134-8 (CANH) - G134-19 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G134-9 (CANH) - G134-20 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| G134-11 (CANH) - G134-22 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to airbag sensor assembly CAN branch wire) | B |
| NG (to spiral with sensor cable sub-assembly [steering angle sensor] CAN branch wire) | C |
| NG (to power steering ECU assembly CAN branch wire) | D |
| NG (to main body ECU [multiplex network body ECU] CAN branch wire) | E |
| NG (to 4WD ECU assembly CAN branch wire) | F |
| NG (to combination meter assembly CAN main wire) | G |
| NG (to air conditioning amplifier assembly CAN branch wire) | H |
| NG (to No. 21 CAN junction connector CAN main wire) | I |
A
B
C
D
E
F
G
H
I
Reconnect the No. 4 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
Reconnect the No. 4 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
Reconnect the No. 4 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
Reconnect the No. 4 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
Reconnect the No. 4 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
Reconnect the No. 4 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
Reconnect the No. 4 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly) |
Disconnect the air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G80-8 (CANH) - G80-9 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG