Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2012.12–2013.11
RM30B0U _57 Power Source / Network _009133 NETWORKING _0050933 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Short to GND in CAN Bus Line  


DESCRIPTION

There may be a short circuit between the CAN bus lines and GND when the resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of the DLC3 is below 200 Ω.

Symptom Trouble Area

*1: w/ Blind Spot Monitor System

*2: w/ Lane Departure Alert System

*3: for Radio and Display Type

*4: for AWD

*5: w/ Smart Key System

*6: for 2 Pin Connector Type

*7: for 22 Pin Connector Type

The resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of the DLC3 is below 200 Ω.
·

Short between CAN bus lines and GND

·

ECM

·

Blind spot monitor sensor LH*1

·

Brake actuator assembly (skid control ECU)

·

Power steering ECU assembly

·

Main body ECU (multiplex network body ECU)

·

Lane departure warning camera*2

·

Air conditioning amplifier assembly

·

Radio and display receiver assembly*3

·

4WD ECU assembly*4

·

Certification ECU (smart key ECU assembly)*5

·

Spiral with sensor cable sub-assembly (steering angle sensor)

·

Airbag sensor assembly

·

Combination meter assembly

·

No. 1 CAN junction connector*6

·

No. 2 CAN junction connector*6

·

No. 3 CAN junction connector*6

·

No. 4 CAN junction connector*7

·

No. 21 CAN junction connector*7

·

DLC3 CAN branch wire or connector



WIRING DIAGRAM

C281139
6.229,1.875 6.688,2.073 0.458,0.198 10 false A62 6.229,2.052 6.688,2.25 0.458,0.198 10 false ECM 5.76,1.333 6.219,1.531 0.458,0.198 10 false 26 5.76,0.823 6.219,1.021 0.458,0.198 10 false 13 0.094,0.094 2.656,0.594 2.563,0.5 12 false for 2 Pin Connector Type: 6.042,1.583 6.552,1.781 0.51,0.198 10 false CANL 6.052,0.823 6.563,1.021 0.51,0.198 10 false CANH 0.771,0.948 1.281,1.146 0.51,0.198 10 false CA1P 0.771,1.469 1.281,1.667 0.51,0.198 10 false CA1N 1.271,0.823 1.729,1.021 0.458,0.198 10 false 2 1.271,1.354 1.729,1.552 0.458,0.198 10 false 7 0.208,1.833 0.667,2.031 0.458,0.198 10 false R1 0.208,2.01 2.563,2.396 2.354,0.385 10 false Blind Spot Monitor Sensor LH*1 3.896,1.469 4.354,1.667 0.458,0.198 10 false N27 3.906,0.938 4.365,1.135 0.458,0.198 10 false N27 2.75,0.938 3.208,1.135 0.458,0.198 10 false N29 2.75,1.458 3.208,1.656 0.458,0.198 10 false N29 2.823,1.24 3.281,1.438 0.458,0.198 10 false 2 3.969,1.25 4.427,1.448 0.458,0.198 10 false 2 3.969,0.708 4.427,0.906 0.458,0.198 10 false 1 2.823,0.708 3.281,0.906 0.458,0.198 10 false 1 3.99,2.281 4.448,2.479 0.458,0.198 10 false 1 3.979,2.833 4.438,3.031 0.458,0.198 10 false 2 3.896,2.521 4.354,2.719 0.458,0.198 10 false N28 3.896,3.052 4.354,3.25 0.458,0.198 10 false N28 2.656,3.458 4.615,3.75 1.958,0.292 10 false No. 3 CAN Junction Connector 2.49,8.375 4.448,8.667 1.958,0.292 10 false No. 1 CAN Junction Connector 0.198,8.385 2.563,8.688 2.365,0.302 10 false *1: w/ Blind Spot Monitor System 3.854,4.25 4.313,4.448 0.458,0.198 10 false G118 3.854,4.781 4.313,4.979 0.458,0.198 10 false G118 2.708,4.26 3.167,4.458 0.458,0.198 10 false G120 2.708,4.792 3.167,4.99 0.458,0.198 10 false G120 2.708,6.375 3.167,6.573 0.458,0.198 10 false G122 2.708,6.906 3.167,7.104 0.458,0.198 10 false G122 3.865,6.896 4.323,7.094 0.458,0.198 10 false G121 3.854,6.375 4.313,6.573 0.458,0.198 10 false G121 3.99,4.563 4.448,4.76 0.458,0.198 10 false 2 3.979,6.677 4.438,6.875 0.458,0.198 10 false 2 2.844,6.667 3.302,6.865 0.458,0.198 10 false 2 2.844,4.552 3.302,4.75 0.458,0.198 10 false 2 2.833,4.01 3.292,4.208 0.458,0.198 10 false 1 3.99,4.031 4.448,4.229 0.458,0.198 10 false 1 3.958,6.115 4.417,6.313 0.458,0.198 10 false 1 2.813,6.146 3.271,6.344 0.458,0.198 10 false 1 1.281,6.24 1.74,6.438 0.458,0.198 10 false 3 1.302,6.802 1.76,7 0.458,0.198 10 false 2 0.729,6.417 1.24,6.615 0.51,0.198 10 false CANH 0.698,4.302 1.208,4.5 0.51,0.198 10 false CANH 6.063,6.385 6.573,6.583 0.51,0.198 10 false CANH 6.073,6.917 6.583,7.115 0.51,0.198 10 false CANL 0.76,6.927 1.271,7.125 0.51,0.198 10 false CANL 0.74,4.802 1.25,5 0.51,0.198 10 false CANL 1.281,4.146 1.74,4.344 0.458,0.198 10 false 25 1.292,4.667 1.75,4.865 0.458,0.198 10 false 14 5.802,6.271 6.26,6.469 0.458,0.198 10 false 4 5.792,6.76 6.25,6.958 0.458,0.198 10 false 8 5.656,7.271 6.958,7.604 1.302,0.333 10 false h1 5.656,7.438 6.958,7.771 1.302,0.333 10 false Power Steering ECU Assembly 0.156,7.281 1.458,7.615 1.302,0.333 10 false G12 0.156,7.448 2.583,7.823 2.427,0.375 10 false Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor) 0.156,5.177 1.75,5.521 1.594,0.344 10 false A64 0.146,5.354 1.74,5.698 1.594,0.344 10 false Brake Actuator Assembly (Skid Control ECU)

C281140
2.542,4.167 4.615,4.417 2.073,0.25 10 false No. 1 CAN Junction Connector 3.854,0.927 4.229,1.302 0.375,0.375 10 false G123 3.854,1.448 4.229,1.823 0.375,0.375 10 false G123 2.719,1.438 3.094,1.813 0.375,0.375 10 false G124 2.698,0.917 3.073,1.292 0.375,0.375 10 false G124 2.698,3.031 3.073,3.406 0.375,0.375 10 false G125 2.698,3.573 3.073,3.948 0.375,0.375 10 false G125 3.865,3.042 4.24,3.417 0.375,0.375 10 false G119 3.854,3.573 4.229,3.948 0.375,0.375 10 false G119 3.979,3.354 4.354,3.729 0.375,0.375 10 false 2 2.854,3.354 3.229,3.729 0.375,0.375 10 false 2 2.854,2.802 3.229,3.177 0.375,0.375 10 false 1 2.833,1.24 3.208,1.615 0.375,0.375 10 false 2 3.979,1.24 4.354,1.615 0.375,0.375 10 false 2 3.969,2.813 4.344,3.188 0.375,0.375 10 false 1 3.979,0.688 4.354,1.063 0.375,0.375 10 false 1 2.833,0.708 3.208,1.083 0.375,0.375 10 false 1 6.042,0.948 6.521,1.302 0.479,0.354 10 false CANH 6.052,1.479 6.531,1.833 0.479,0.354 10 false CANL 0.729,0.938 1.208,1.292 0.479,0.354 10 false CANH 0.75,1.479 1.229,1.833 0.479,0.354 10 false CANL 0.688,3.063 1.167,3.417 0.479,0.354 10 false CA1P 0.708,3.583 1.188,3.938 0.479,0.354 10 false CA1N 5.75,0.833 6.229,1.188 0.479,0.354 10 false 14 5.76,1.354 6.24,1.708 0.479,0.354 10 false 13 1.271,0.813 1.75,1.167 0.479,0.354 10 false 6 1.281,1.354 1.76,1.708 0.479,0.354 10 false 14 1.26,2.927 1.74,3.281 0.479,0.354 10 false 6 1.271,3.458 1.75,3.813 0.479,0.354 10 false 12 0.5,1.854 0.979,2.208 0.479,0.354 10 false G14 5.396,1.844 5.875,2.198 0.479,0.354 10 false G78 5.396,2.031 7.042,2.375 1.646,0.344 10 false Main Body ECU (Multiplex Network Body ECU) 0.104,3.979 2.26,4.188 2.156,0.208 10 false Q13 0.115,4.135 2.344,4.333 2.229,0.198 10 false Lane Departure Warning Camera*2 0.115,7.604 2.802,7.844 2.688,0.24 10 false *3: for Automatic Air Conditioning System 3.865,4.917 4.24,5.292 0.375,0.375 10 false G129 3.844,5.448 4.219,5.823 0.375,0.375 10 false G129 2.708,5.448 3.083,5.823 0.375,0.375 10 false G126 2.708,4.917 3.083,5.292 0.375,0.375 10 false G126 3.854,6.781 4.229,7.156 0.375,0.375 10 false G130 3.854,7.302 4.229,7.677 0.375,0.375 10 false G130 3.99,5.229 4.365,5.604 0.375,0.375 10 false 2 3.99,7.083 4.365,7.458 0.375,0.375 10 false 2 2.833,5.229 3.208,5.604 0.375,0.375 10 false 2 2.813,4.698 3.188,5.073 0.375,0.375 10 false 1 3.969,4.698 4.344,5.073 0.375,0.375 10 false 1 3.969,6.531 4.344,6.906 0.375,0.375 10 false 1 2.521,8.26 4.594,8.51 2.073,0.25 10 false No. 2 CAN Junction Connector 0.719,4.927 1.198,5.281 0.479,0.354 10 false CANH 0.729,5.49 1.208,5.844 0.479,0.354 10 false CANL 0.51,2.042 0.99,2.396 0.479,0.354 10 false DLC3 0.198,5.865 1.76,6.208 1.563,0.344 10 false Air Conditioning Amplifier Assembly 5.271,7.688 6.969,8.021 1.698,0.333 10 false G143 5.281,7.854 6.979,8.188 1.698,0.333 10 false Radio and Display Receiver Assembly*5 6.021,6.792 6.5,7.146 0.479,0.354 10 false CANH 6.031,7.313 6.51,7.667 0.479,0.354 10 false CANL 5.813,6.677 6.292,7.031 0.479,0.354 10 false 9 5.75,7.208 6.125,7.583 0.375,0.375 10 false 10 1.292,5.448 1.667,5.823 0.375,0.375 10 false G81 1.302,4.927 1.677,5.302 0.375,0.375 10 false G81 1.76,4.927 2.135,5.302 0.375,0.375 10 false G80 1.75,5.448 2.125,5.823 0.375,0.375 10 false G80 1.771,5.208 2.146,5.583 0.375,0.375 10 false 9*4 1.781,4.677 2.156,5.052 0.375,0.375 10 false 8*4 1.281,5.219 1.656,5.594 0.375,0.375 10 false 12*3 1.281,4.688 1.656,5.063 0.375,0.375 10 false 11*3 0.115,7.292 2.427,7.5 2.313,0.208 10 false *2: w/ Lane Departure Alert System 0.125,7.896 2.813,8.135 2.688,0.24 10 false *4: for Manual Air Conditioning System 0.125,8.198 2.813,8.438 2.688,0.24 10 false *5: for Radio and Display Type 0.146,0.104 2.354,0.552 2.208,0.448 12 false for 2 Pin Connector Type:

C277471
2.5,3.833 4.417,4.125 1.917,0.292 10 false No. 2 CAN Junction Connector 5.833,3.792 7,4.167 1.167,0.375 10 false G16 5.833,3.958 7,4.333 1.167,0.375 10 false Combination Meter Assembly 5.75,2.792 6.5,3 0.75,0.208 10 false 32 6.042,3.542 6.792,3.75 0.75,0.208 10 false CANL 6.031,2.792 6.781,3 0.75,0.208 10 false CANH 5.75,3.333 6.5,3.542 0.75,0.208 10 false 31 6.031,0.792 6.781,1 0.75,0.208 10 false CANH 6.031,1.313 6.781,1.521 0.75,0.208 10 false CANL 3.885,0.781 5.052,1.156 1.167,0.375 10 false G131 3.875,1.292 5.042,1.667 1.167,0.375 10 false G131 4,0.552 4.75,0.76 0.75,0.208 10 false 1 4,1.073 4.75,1.281 0.75,0.208 10 false 2 2.844,0.542 3.594,0.75 0.75,0.208 10 false 1 2.844,2.667 3.594,2.875 0.75,0.208 10 false 1 3.99,2.667 4.74,2.875 0.75,0.208 10 false 1 2.854,1.073 3.604,1.281 0.75,0.208 10 false 2 2.854,3.188 3.604,3.396 0.75,0.208 10 false 2 4.021,3.188 4.771,3.396 0.75,0.208 10 false 2 2.729,0.781 3.896,1.156 1.167,0.375 10 false G132 2.719,1.292 3.885,1.667 1.167,0.375 10 false G132 3.875,2.885 5.042,3.26 1.167,0.375 10 false G128 3.875,3.406 5.042,3.781 1.167,0.375 10 false G128 2.719,3.406 3.885,3.781 1.167,0.375 10 false G133 2.729,2.896 3.896,3.271 1.167,0.375 10 false G133 0.75,0.823 1.5,1.031 0.75,0.208 10 false CANH 0.771,1.313 1.521,1.521 0.75,0.208 10 false CANL 0.76,3.438 1.51,3.646 0.75,0.208 10 false CANL 0.729,2.906 1.479,3.115 0.75,0.208 10 false CANH 1.271,2.771 2.021,2.979 0.75,0.208 10 false 13 1.281,3.302 2.031,3.51 0.75,0.208 10 false 22 1.26,0.667 2.01,0.875 0.75,0.208 10 false 14 1.26,1.188 2.01,1.396 0.75,0.208 10 false 15 5.802,0.677 6.552,0.885 0.75,0.208 10 false 6 5.823,1.188 6.573,1.396 0.75,0.208 10 false 5 5.563,1.708 6.729,2.083 1.167,0.375 10 false G86 5.573,1.875 7.104,2.094 1.531,0.219 10 false 4WD ECU Assembly*6 0.333,4.417 2.25,4.708 1.917,0.292 10 false *6: for AWD 1.229,4.417 3.146,4.708 1.917,0.292 10 false *7: w/ Smart Key System 0.167,3.792 1.333,4.167 1.167,0.375 10 false G92 0.167,3.958 2.25,4.167 2.083,0.208 10 false Airbag Sensor Assembly 0.167,1.677 1.333,2.052 1.167,0.375 10 false G84 0.167,1.844 2,2.219 1.833,0.375 10 false Certification ECU (Smart Key ECU Assembly)*7 0.115,0.083 2.875,0.49 2.76,0.406 12 false for 2 Pin Connector Type:

C281141
0.115,0.125 2.219,0.552 2.104,0.427 12 false for 22 Pin Connector Type: 6.021,0.823 6.573,1.115 0.552,0.292 10 false CANH 6.042,1.583 6.594,1.875 0.552,0.292 10 false CANL 0.719,0.969 1.271,1.26 0.552,0.292 10 false CANH 0.75,1.49 1.302,1.781 0.552,0.292 10 false CANL 0.76,4.823 1.313,5.115 0.552,0.292 10 false CANL 0.74,4.271 1.292,4.563 0.552,0.292 10 false CANH 0.719,6.406 1.271,6.698 0.552,0.292 10 false CANH 0.76,6.917 1.313,7.208 0.552,0.292 10 false CANL 6.042,6.906 6.594,7.198 0.552,0.292 10 false CANL 6.042,6.375 6.594,6.667 0.552,0.292 10 false CANH 6.208,1.865 6.76,2.156 0.552,0.292 10 false A62 6.219,2.021 6.771,2.313 0.552,0.292 10 false ECM 0.156,1.865 0.708,2.156 0.552,0.292 10 false A64 0.156,2.042 1.76,2.396 1.604,0.354 10 false Brake Actuator Assembly (Skid Control ECU) 1.25,0.833 1.802,1.125 0.552,0.292 10 false 25 1.25,1.354 1.802,1.646 0.552,0.292 10 false 14 3.844,2.958 4.396,3.25 0.552,0.292 10 false 14 2.917,1.344 3.469,1.635 0.552,0.292 10 false 12 3.854,0.833 4.406,1.125 0.552,0.292 10 false 2 2.979,0.823 3.531,1.115 0.552,0.292 10 false 1 3.854,1.354 4.406,1.646 0.552,0.292 10 false 13 3.875,2.427 4.427,2.719 0.552,0.292 10 false 3 5.74,0.833 6.292,1.125 0.552,0.292 10 false 13 5.75,1.333 6.302,1.625 0.552,0.292 10 false 26 2.604,3.438 4.75,3.75 2.146,0.313 10 false A72 2.604,3.583 4.75,3.896 2.146,0.313 10 false No. 21 CAN Junction Connector 2.531,8.323 4.677,8.635 2.146,0.313 10 false G134 2.531,8.479 4.677,8.792 2.146,0.313 10 false No. 4 CAN Junction Connector 1.281,6.24 3.427,6.552 2.146,0.313 10 false 3 1.281,6.813 3.427,7.125 2.146,0.313 10 false 2 0.167,7.281 2.313,7.594 2.146,0.313 10 false G12 0.177,7.448 2.594,7.854 2.417,0.406 10 false Spiral with Sensor Cable sub-assembly (Steering Angle Sensor) 5.458,7.292 6.792,7.646 1.333,0.354 10 false G80 5.458,7.448 7.031,7.781 1.573,0.333 10 false Air Conditioning Amplifier Assembly 5.823,6.792 7.156,7.146 1.333,0.354 10 false 9 5.823,6.26 7.156,6.615 1.333,0.354 10 false 8 3.854,6.271 5.188,6.625 1.333,0.354 10 false 2 3.854,6.792 5.188,7.146 1.333,0.354 10 false 13 0.208,5.177 1.573,5.542 1.365,0.365 10 false G92 0.198,5.344 2.094,5.74 1.896,0.396 10 false Airbag Sensor Assembly 1.271,4.156 2.604,4.51 1.333,0.354 10 false 13 1.281,4.688 2.615,5.042 1.333,0.354 10 false 22 2.969,4.156 4.302,4.51 1.333,0.354 10 false 1 2.896,4.688 4.229,5.042 1.333,0.354 10 false 12 3.875,4.688 5.208,5.042 1.333,0.354 10 false 22 3.865,4.167 5.198,4.521 1.333,0.354 10 false 11 2.958,6.26 5.104,6.573 2.146,0.313 10 false 3 2.906,6.792 5.052,7.104 2.146,0.313 10 false 14

C281142
0.156,0.104 3,0.458 2.844,0.354 12 false for 22 Pin Connector Type: 0.688,0.979 1.333,1.271 0.646,0.292 10 false CANH 0.698,1.49 1.344,1.781 0.646,0.292 10 false CANL 0.688,3.083 1.333,3.375 0.646,0.292 10 false CANH 5.99,5.094 6.635,5.385 0.646,0.292 10 false CANH 6.01,3.083 6.656,3.375 0.646,0.292 10 false CANH 6.021,0.958 6.667,1.25 0.646,0.292 10 false CANH 6.063,1.5 6.708,1.792 0.646,0.292 10 false CANL 6.021,3.615 6.667,3.906 0.646,0.292 10 false CANL 6,5.844 6.646,6.135 0.646,0.292 10 false CANL 0.719,3.615 1.365,3.906 0.646,0.292 10 false CANL 1.229,3.479 1.875,3.771 0.646,0.292 10 false 14 1.219,2.958 1.865,3.25 0.646,0.292 10 false 6 0.49,3.99 1.135,4.281 0.646,0.292 10 false G14 0.49,4.156 1.135,4.448 0.646,0.292 10 false DLC3 2.865,2.948 3.51,3.24 0.646,0.292 10 false 10 2.865,3.5 3.51,3.792 0.646,0.292 10 false 21 3.844,0.854 4.49,1.146 0.646,0.292 10 false 4 3.833,1.385 4.479,1.677 0.646,0.292 10 false 15 2.875,1.385 3.521,1.677 0.646,0.292 10 false 16 2.948,0.844 3.594,1.135 0.646,0.292 10 false 5 0.177,1.885 0.823,2.177 0.646,0.292 10 false G78 0.177,2.063 1.813,2.406 1.635,0.344 10 false Main Body ECU (Multiplex Network Body ECU) 5.719,1.885 7,2.219 1.281,0.333 10 false h1 5.719,2.031 7,2.365 1.281,0.333 10 false Power Steering ECU Assembly 3.844,5.094 4.49,5.385 0.646,0.292 10 false 9 3.854,5.604 4.5,5.896 0.646,0.292 10 false 20 5.792,0.865 6.438,1.156 0.646,0.292 10 false 4 5.792,1.365 6.438,1.656 0.646,0.292 10 false 8 1.24,0.854 1.885,1.146 0.646,0.292 10 false 14 1.25,1.375 1.896,1.667 0.646,0.292 10 false 13 5.719,5.073 6.365,5.365 0.646,0.292 10 false 32 5.719,5.604 6.365,5.896 0.646,0.292 10 false 31 5.771,6.24 6.958,6.594 1.188,0.354 10 false Combination Meter Assembly 5.76,6.083 6.917,6.448 1.156,0.365 10 false G16 5.792,2.969 6.438,3.26 0.646,0.292 10 false 6 5.813,3.5 6.458,3.792 0.646,0.292 10 false 5 5.625,3.958 6.781,4.323 1.156,0.365 10 false G86 5.646,4.125 6.969,4.49 1.323,0.365 10 false 4WD ECU Assembly 3.854,2.958 4.5,3.25 0.646,0.292 10 false 8 3.844,3.49 4.49,3.781 0.646,0.292 10 false 19 2.563,6.135 5.208,6.396 2.646,0.26 10 false G134 2.573,6.302 5.219,6.563 2.646,0.26 10 false No. 4 CAN Junction Connector

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the Precaution in the SRS.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

·

Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicles type.


Result:
Proceed to
for 2 Pin Connector Type
for 22 Pin Connector Type



for 2 Pin Connector Type

2.CHECK FOR SHORT TO GND IN CAN BUS WIRE (DLC3 CAN BRANCH WIRE)

for 22 Pin Connector Type

39.CHECK FOR SHORT TO GND IN CAN BUS WIRE (DLC3 CAN BRANCH WIRE)
2.CHECK FOR SHORT TO GND IN CAN BUS WIRE (DLC3 CAN BRANCH WIRE)
a.
C253362
0.146,1.125 0.542,1.365 0.396,0.24 1.958,0.917 2.333,0.417 2.333,0.417 2.583,0.417 true 1.948,1.49 1.625,1.917 1.625,1.917 1.375,1.917 true 1.563,0.906 1.292,0.531 1.292,0.531 1.052,0.531 true 0.208,1.167 0.479,1.333 0.271,0.167 10 G14 0.094,0.115 0.365,0.281 0.271,0.167 10 *a 2.625,0.333 3.094,0.5 0.469,0.167 10 CANH 0.948,1.833 1.417,2 0.469,0.167 10 CANL 0.823,0.458 1.156,0.708 0.333,0.25 10 CG
*a Front view of DLC3


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the G124 No. 1 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G14-6 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G14-14 (CANL) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

3.CONNECT CONNECTOR

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)

3.CONNECT CONNECTOR
a.

Reconnect the No. 1 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

4.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR SIDE)
4.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR SIDE)
a.
C253362
0.146,1.125 0.542,1.365 0.396,0.24 1.958,0.917 2.333,0.417 2.333,0.417 2.583,0.417 true 1.948,1.49 1.625,1.917 1.625,1.917 1.375,1.917 true 1.563,0.906 1.292,0.531 1.292,0.531 1.052,0.531 true 0.208,1.167 0.479,1.333 0.271,0.167 10 G14 0.094,0.115 0.365,0.281 0.271,0.167 10 *a 2.625,0.333 3.094,0.5 0.469,0.167 10 CANH 0.948,1.833 1.417,2 0.469,0.167 10 CANL 0.823,0.458 1.156,0.708 0.333,0.25 10 CG
*a Front view of DLC3


Disconnect the N28 No. 3 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G14-6 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G14-14 (CANL) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

5.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR)

NG

10.CONNECT CONNECTOR
5.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 3 CAN junction connectors.

C278754
5.625,2.219 6.104,2.521 0.479,0.302 5.271,2.438 5.469,2.438 5.469,2.438 5.646,2.75 true 3.615,3.271 3.469,3.26 3.469,3.26 3.323,3 true 3.625,2.625 3.458,2.625 3.458,2.625 3.313,2.865 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *1 2.531,2.385 2.844,2.583 0.313,0.198 10 false *a 4.531,2.333 4.844,2.531 0.313,0.198 10 false *b 5.042,2.365 5.427,2.583 0.385,0.219 10 false CG 3.667,2.552 4.208,2.781 0.542,0.229 10 false CANH 3.677,3.177 4.219,3.406 0.542,0.229 10 false CANL 1.385,2.115 1.927,2.344 0.542,0.229 10 false N29 1.385,1.667 1.927,1.896 0.542,0.229 10 false N27 5.719,2.25 6.26,2.479 0.542,0.229 10 false G14
*1 No. 3 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 3 CAN Junction Connector)
*b Front view of DLC3


Code Color (CANH Side) Color (CANL Side) Connect to

*: w/ Blind Spot Monitor System

N27 Y W ECM
N29 R W Blind Spot Monitor Sensor LH*


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N27-1 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
N27-2 (CANL) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
N29-1 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
N29-2 (CANL) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG (to ECM CAN main wire)
NG (to blind spot monitor sensor LH CAN branch wire)



OK

REPLACE NO. 3 CAN JUNCTION CONNECTOR

NG (to ECM CAN main wire)

6.CONNECT CONNECTOR

NG (to blind spot monitor sensor LH CAN branch wire)

8.CONNECT CONNECTOR
6.CONNECT CONNECTOR
a.

Reconnect all wire harness No. 3 CAN junction connectors.


Result:
Proceed to
NEXT



NEXT

7.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECM)
7.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECM)
a.
C229085
0.115,0.917 0.583,1.208 0.469,0.292 0.375,2.552 0.844,2.844 0.469,0.292 2.448,0.917 2.688,0.635 2.688,0.635 2.823,0.635 true 2.448,1.01 2.708,1.292 2.708,1.292 2.823,1.292 true 1.26,2.115 1.448,2.115 1.448,2.115 1.635,2.458 true 0.104,0.104 0.417,0.26 0.313,0.156 10 false *a 0.146,1.958 0.458,2.115 0.313,0.156 10 false *b 0.219,0.979 0.625,1.208 0.406,0.229 10 false A62 0.479,2.615 0.885,2.844 0.406,0.229 10 false G14 1.031,2.021 1.438,2.25 0.406,0.229 10 false CG 2.875,1.188 3.385,1.417 0.51,0.229 10 false CANL 2.875,0.542 3.385,0.771 0.51,0.229 10 false CANH
*a Front view of wire harness connector
(to ECM)
*b Front view of DLC3


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A62-13 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
A62-26 (CANL) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)

8.CONNECT CONNECTOR
a.

Reconnect all wire harness No. 3 CAN junction connectors.


Result:
Proceed to
NEXT



NEXT

9.CHECK FOR SHORT TO GND IN CAN BUS WIRE (BLIND SPOT MONITOR SENSOR LH)
9.CHECK FOR SHORT TO GND IN CAN BUS WIRE (BLIND SPOT MONITOR SENSOR LH)
a.
C268298
1.531,1.948 1.948,2.208 0.417,0.26 1.469,0.24 1.885,0.5 0.417,0.26 1.563,1.063 1.188,0.719 1.188,0.719 0.958,0.719 true 1.563,1.198 1.198,1.531 1.198,1.531 0.969,1.531 true 1.646,2.531 1.344,2.125 1.344,2.125 1.094,2.125 true 0.073,0.083 0.385,0.24 0.313,0.156 10 *a 0.104,1.979 0.417,2.135 0.313,0.156 10 *b 0.563,0.646 1.042,0.917 0.479,0.271 10 CA1P 0.573,1.469 1.052,1.74 0.479,0.271 10 CA1N 0.854,2.052 1.344,2.25 0.49,0.198 10 CG 1.573,0.292 1.969,0.469 0.396,0.177 10 R1 1.604,2 2,2.177 0.396,0.177 10 G14
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)
*b Front view of DLC3


Disconnect the blind spot monitor sensor LH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R1-2 (CA1P) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
R1-7 (CA1N) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO BLIND SPOT MONITOR SENSOR LH (CA1P, CA1N)

10.CONNECT CONNECTOR
a.

Reconnect the No. 3 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

11.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - NO. 3 CAN JUNCTION CONNECTOR)
11.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - NO. 3 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 1 CAN junction connector.

C253917
5.521,2.229 5.927,2.479 0.406,0.25 3.302,2.875 3.469,2.698 3.469,2.698 3.552,2.698 true 3.302,3.01 3.458,3.177 3.458,3.177 3.542,3.177 true 5.635,2.74 5.406,2.427 5.406,2.427 5.24,2.427 true 0.063,0.042 0.375,0.198 0.313,0.156 10 *1 3.604,2.635 4.167,2.844 0.563,0.208 10 CANH 2.521,2.417 2.833,2.573 0.313,0.156 10 *a 4.604,2.344 4.917,2.5 0.313,0.156 10 *b 3.594,3.115 4.156,3.323 0.563,0.208 10 CANL 5,2.354 5.563,2.563 0.563,0.208 10 CG 5.583,2.281 6.146,2.49 0.563,0.208 10 G14 1.344,1.677 1.906,1.885 0.563,0.208 10 G118
*1 No. 1 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 1 CAN Junction Connector)
*b Front view of DLC3


Code Color (CANH Side) Color (CANL Side) Connect to
G118 L W No. 3 CAN Junction Connector


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G118-1 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G118-2 (CANL) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

12.CONNECT CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - NO. 3 CAN JUNCTION CONNECTOR)

12.CONNECT CONNECTOR
a.

Reconnect the No. 1 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

13.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR SIDE)
13.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR SIDE)
a.
C253362
0.146,1.125 0.542,1.365 0.396,0.24 1.958,0.917 2.333,0.417 2.333,0.417 2.583,0.417 true 1.948,1.49 1.625,1.917 1.625,1.917 1.375,1.917 true 1.563,0.906 1.292,0.531 1.292,0.531 1.052,0.531 true 0.208,1.167 0.479,1.333 0.271,0.167 10 G14 0.094,0.115 0.365,0.281 0.271,0.167 10 *a 2.625,0.333 3.094,0.5 0.469,0.167 10 CANH 0.948,1.833 1.417,2 0.469,0.167 10 CANL 0.823,0.458 1.156,0.708 0.333,0.25 10 CG
*a Front view of DLC3


Disconnect the G129 No. 2 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G14-6 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G14-14 (CANL) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

14.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR)

NG

27.CONNECT CONNECTOR
14.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 2 CAN junction connectors.

C281144
5.521,2.229 5.906,2.5 0.385,0.271 5.208,2.427 5.375,2.427 5.375,2.427 5.646,2.76 true 3.333,3.01 3.458,3.208 3.458,3.208 3.615,3.208 true 3.313,2.885 3.49,2.677 3.49,2.677 3.646,2.677 true 0.146,0.115 0.458,0.313 0.313,0.198 10 false *1 2.531,2.417 2.844,2.615 0.313,0.198 10 false *a 4.594,2.313 4.906,2.51 0.313,0.198 10 false *b 4.979,2.313 5.375,2.51 0.396,0.198 10 false CG 5.583,2.271 5.979,2.469 0.396,0.198 10 false G14 3.688,2.552 4.135,2.76 0.448,0.208 10 false CANH 3.656,3.094 4.104,3.302 0.448,0.208 10 false CANL 1.344,1.667 1.792,1.875 0.448,0.208 10 false G126 1.344,1.885 1.792,2.094 0.448,0.208 10 false G128 1.344,2.563 1.792,2.771 0.448,0.208 10 false G131 1.344,2.323 1.792,2.531 0.448,0.208 10 false G130 1.344,2.781 1.792,2.99 0.448,0.208 10 false G132 1.354,3 1.802,3.208 0.448,0.208 10 false G133
*1 No. 2 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 2 CAN Junction Connector)
*b Front view of DLC3


Code Color (CANH Side) Color (CANL Side) Connect to

*1: for Radio and Display Type

*2: for AWD

*3: w/ Smart Key System

G126 B W Air Conditioning Amplifier Assembly
G128 G W Combination Meter Assembly
G130 Y W Radio and Display Receiver Assembly*1
G131 L W 4WD ECU Assembly*2
G132 R W Certification ECU (Smart Key ECU Assembly)*3
G133 BR W Airbag Sensor Assembly


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G126-1 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G126-2 (CANL) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G128-1 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G128-2 (CANL) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G130-1 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G130-2 (CANL) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G131-1 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G131-2 (CANL) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G132-1 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G132-2 (CANL) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G133-1 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G133-2 (CANL) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Result Proceed to
OK A
NG (to air conditioning amplifier assembly CAN branch wire) B
NG (to combination meter assembly CAN main wire) C
NG (to radio and display receiver assembly CAN branch wire) D
NG (to 4WD ECU assembly CAN branch wire) E
NG (to certification ECU [smart key ECU assembly] CAN branch wire) F
NG (to airbag sensor assembly CAN branch wire) G



A

REPLACE NO. 2 CAN JUNCTION CONNECTOR

B

15.CONNECT CONNECTOR

C

17.CONNECT CONNECTOR

D

19.CONNECT CONNECTOR

E

21.CONNECT CONNECTOR

F

23.CONNECT CONNECTOR

G

25.CONNECT CONNECTOR
15.CONNECT CONNECTOR
a.

Reconnect all wire harness No. 2 CAN junction connectors.


Result:
Proceed to
NEXT



NEXT

16.CHECK FOR SHORT TO GND IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY)
16.CHECK FOR SHORT TO GND IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the air conditioning amplifier assembly connector.

C278756
5.729,0.698 6.146,0.948 0.417,0.25 3.438,0.521 3.854,0.771 0.417,0.25 1.167,0.552 1.583,0.802 0.417,0.25 5.844,1.313 5.625,0.948 5.625,0.948 5.438,0.948 true 1.333,1.49 1.823,2.104 1.823,2.104 2.021,2.104 true 1.24,1.479 1.49,2.365 1.49,2.365 1.688,2.365 true 2.49,0.979 2.74,0.979 2.74,0.979 3.021,1.396 true 2.635,0.729 2.885,0.729 2.885,0.729 3.125,1.406 true 1.24,0.594 1.698,0.792 0.458,0.198 10 G81 0.125,0.083 0.583,0.281 0.458,0.198 10 *a 5,0.135 5.458,0.333 0.458,0.198 10 *b 3.5,0.552 3.958,0.75 0.458,0.198 10 G80 5.792,0.75 6.25,0.948 0.458,0.198 10 G14 2.083,0.906 2.542,1.104 0.458,0.198 10 CANL 2.083,2.031 2.542,2.229 0.458,0.198 10 CANH 1.75,2.292 2.208,2.49 0.458,0.198 10 CANL 2.229,0.656 2.688,0.854 0.458,0.198 10 CANH 5.208,0.875 5.542,1.219 0.333,0.344 10 CG 3.938,0.563 4.396,0.76 0.458,0.198 10 *B 1.646,0.583 2.104,0.781 0.458,0.198 10 *A
*A for Automatic Air Conditioning System *B for Manual Air Conditioning System
*a Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly)
*b Front view of DLC3



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for Automatic Air Conditioning System
Tester Connection Condition Specified Condition
G81-11 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G81-12 (CANL) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher

for Manual Air Conditioning System
Tester Connection Condition Specified Condition
G80-8 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G80-9 (CANL) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIR CONDITIONING AMPLIFIER ASSEMBLY (CANH, CANL)

17.CONNECT CONNECTOR
a.

Reconnect all wire harness No. 2 CAN junction connectors.


Result:
Proceed to
NEXT



NEXT

18.CHECK FOR SHORT TO GND IN CAN BUS WIRE (COMBINATION METER ASSEMBLY)
18.CHECK FOR SHORT TO GND IN CAN BUS WIRE (COMBINATION METER ASSEMBLY)
a.
C235425
0.354,0.948 0.771,1.198 0.417,0.25 0.344,2.531 0.76,2.781 0.417,0.25 1.615,2.49 1.396,2.188 1.396,2.188 1.188,2.188 true 2.167,1.667 2,1.667 2,1.667 1.688,1.167 true 1.083,1.667 1.333,1.667 1.333,1.667 1.604,1.167 true 0.083,0.083 0.333,0.333 0.25,0.25 10 *a 0.167,2.01 0.479,2.167 0.313,0.156 10 *b 0.417,2.583 0.833,2.833 0.417,0.25 10 G14 0.417,1 0.833,1.25 0.417,0.25 10 G16 0.667,1.583 1.083,1.833 0.417,0.25 10 CANH 2.219,1.583 2.635,1.833 0.417,0.25 10 CANL 0.938,2.125 1.354,2.375 0.417,0.25 10 CG
*a Rear view of wire harness connector
(to Combination Meter Assembly)
*b Front view of DLC3


Disconnect the combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-32 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G16-31 (CANL) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (CANH, CANL)

19.CONNECT CONNECTOR
a.

Reconnect all wire harness No. 2 CAN junction connectors.


Result:
Proceed to
NEXT



NEXT

20.CHECK FOR SHORT TO GND IN CAN BUS WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY)
20.CHECK FOR SHORT TO GND IN CAN BUS WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.
C235427
0.365,2.615 0.792,2.885 0.427,0.271 1.406,0.229 1.802,0.479 0.396,0.25 1.094,2.135 1.281,2.135 1.281,2.135 1.594,2.49 true 1.969,1.177 2.24,1.656 2.24,1.656 2.49,1.656 true 1.833,1.177 1.604,1.646 1.604,1.646 1.396,1.646 true 0.094,0.073 0.406,0.229 0.313,0.156 10 *a 0.115,2.177 0.427,2.333 0.313,0.156 10 *b 0.438,2.667 0.854,2.906 0.417,0.24 10 G14 0.865,2.052 1.281,2.292 0.417,0.24 10 CG 0.948,1.594 1.469,1.885 0.521,0.292 10 CANH 2.552,1.583 3.073,1.875 0.521,0.292 10 CANL 1.438,0.271 1.885,0.542 0.448,0.271 10 G143
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
*b Front view of DLC3


Disconnect the radio and display receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G143-9 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G143-10 (CANL) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO RADIO AND DISPLAY RECEIVER ASSEMBLY (CANH, CANL)

21.CONNECT CONNECTOR
a.

Reconnect all wire harness No. 2 CAN junction connectors.


Result:
Proceed to
NEXT



NEXT

22.CHECK FOR SHORT TO GND IN CAN BUS WIRE (4WD ECU ASSEMBLY)
22.CHECK FOR SHORT TO GND IN CAN BUS WIRE (4WD ECU ASSEMBLY)
a.
C251150
0.417,2.51 0.823,2.792 0.406,0.281 0.438,0.927 0.844,1.208 0.406,0.281 1.188,2.125 1.365,2.125 1.365,2.125 1.646,2.427 true 2.229,1.094 2.438,1.281 2.438,1.281 2.615,1.281 true 2.167,1.094 2.333,1.563 2.333,1.563 2.51,1.563 true 0.083,0.094 0.396,0.25 0.313,0.156 10 *a 0.104,2.083 0.417,2.24 0.313,0.156 10 *b 0.479,2.563 0.854,2.771 0.375,0.208 10 G14 0.958,2.042 1.333,2.25 0.375,0.208 10 CG 2.563,1.49 3.042,1.76 0.479,0.271 10 CANH 2.667,1.198 3.146,1.469 0.479,0.271 10 CANL 0.51,0.99 0.885,1.198 0.375,0.208 10 G86
*a Rear view of wire harness connector
(to 4WD ECU Assembly)
*b Front view of DLC3


Disconnect the 4WD ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G86-6 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G86-5 (CANL) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO 4WD ECU ASSEMBLY (CANH, CANL)

23.CONNECT CONNECTOR
a.

Reconnect all wire harness No. 2 CAN junction connectors.


Result:
Proceed to
NEXT



NEXT

24.CHECK FOR SHORT TO GND IN CAN BUS WIRE (CERTIFICATION ECU)
24.CHECK FOR SHORT TO GND IN CAN BUS WIRE (CERTIFICATION ECU)
a.
C278757
0.333,2.531 0.75,2.823 0.417,0.292 0.271,0.948 0.688,1.24 0.417,0.292 1.25,2.115 1.448,2.115 1.448,2.115 1.635,2.438 true 2.031,1.052 2.344,0.344 2.344,0.344 2.552,0.344 true 1.917,1.031 1.604,0.323 1.604,0.323 1.406,0.323 true 0.167,0.125 0.385,2 0.219,1.875 10 *a 0.167,2.083 0.479,2.24 0.313,0.156 10 *b 0.417,2.583 0.813,2.823 0.396,0.24 10 G14 0.333,1.01 0.729,1.25 0.396,0.24 10 G84 1.021,2.042 1.417,2.281 0.396,0.24 10 CG 2.594,0.271 3.198,0.542 0.604,0.271 10 CANL 0.979,0.271 1.583,0.542 0.604,0.271 10 CANH
*a Front view of wire harness connector
(to Certification ECU [Smart Key ECU Assembly])
*b Front view of DLC3


Disconnect the certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G84-14 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G84-15 (CANL) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CERTIFICATION ECU (CANH, CANL)

25.CONNECT CONNECTOR
a.

Reconnect all wire harness No. 2 CAN junction connectors.


Result:
Proceed to
NEXT



NEXT

26.CHECK FOR SHORT TO GND IN CAN BUS WIRE (AIRBAG SENSOR ASSEMBLY)
26.CHECK FOR SHORT TO GND IN CAN BUS WIRE (AIRBAG SENSOR ASSEMBLY)
a.
C227529
0.375,2.521 0.771,2.781 0.396,0.26 0.365,0.948 0.76,1.208 0.396,0.26 1.656,2.479 1.365,2.073 1.365,2.073 1.167,2.073 true 2.115,1.323 2.313,1.677 2.313,1.677 2.552,1.677 true 2.021,1.01 2.438,0.656 2.438,0.656 2.688,0.656 true 0.177,0.073 0.427,0.271 0.25,0.198 10 *a 0.198,2.083 0.51,2.24 0.313,0.156 10 *b 0.438,2.573 0.781,2.781 0.344,0.208 10 G14 0.417,1 0.76,1.208 0.344,0.208 10 G92 2.75,0.583 3.292,0.792 0.542,0.208 10 CANH 2.604,1.604 3.146,1.813 0.542,0.208 10 CANL 0.948,2 1.49,2.208 0.542,0.208 10 CG
*a Rear view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of DLC3


Disconnect the airbag sensor assembly connector.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G92-13 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G92-22 (CANL) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIRBAG SENSOR ASSEMBLY (CANH, CANL)

27.CONNECT CONNECTOR
a.

Reconnect the No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

28.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR)
28.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 1 CAN junction connectors.

C253917
5.521,2.229 5.927,2.479 0.406,0.25 3.302,2.875 3.469,2.698 3.469,2.698 3.552,2.698 true 3.302,3.01 3.458,3.177 3.458,3.177 3.542,3.177 true 5.229,2.458 5.438,2.458 5.438,2.458 5.656,2.76 true 0.063,0.042 0.375,0.198 0.313,0.156 10 false *1 3.604,2.635 4.167,2.844 0.563,0.208 10 false CANH 2.521,2.417 2.833,2.573 0.313,0.156 10 false *a 4.604,2.344 4.917,2.5 0.313,0.156 10 false *b 3.594,3.115 4.156,3.323 0.563,0.208 10 false CANL 4.979,2.396 5.542,2.604 0.563,0.208 10 false CG 5.583,2.281 6.146,2.49 0.563,0.208 10 false G14 1.344,2.115 1.906,2.323 0.563,0.208 10 false G120 1.344,2.344 1.906,2.552 0.563,0.208 10 false G121 1.333,2.563 1.896,2.771 0.563,0.208 10 false G122 1.344,2.792 1.906,3 0.563,0.208 10 false G123 1.333,3.219 1.896,3.427 0.563,0.208 10 false G125 1.344,1.896 1.906,2.104 0.563,0.208 10 false G119
*1 No. 1 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 1 CAN Junction Connector)
*b Front view of DLC3


Code Color (CANH Side) Color (CANL Side) Connect to

*: w/ Lane Departure Alert System

G119 V W No. 2 CAN Junction Connector
G120 R W Brake Actuator Assembly (Skid Control ECU)
G121 LG W Power Steering ECU Assembly
G122 P W Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor)
G123 Y W Main Body ECU (Multiplex Network Body ECU)
G125 G W Lane Departure Warning Camera*


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G119-1 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G119-2 (CANL) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G120-1 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G120-2 (CANL) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G121-1 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G121-2 (CANL) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G122-1 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G122-2 (CANL) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G123-1 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G123-2 (CANL) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G125-1 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G125-2 (CANL) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Result Proceed to
OK A
NG (to brake actuator assembly [skid control ECU] CAN branch wire) B
NG (to power steering ECU assembly CAN branch wire) C
NG (to spiral with sensor cable sub-assembly [steering angle sensor] CAN branch wire) D
NG (to main body ECU [multiplex network body ECU] CAN branch wire) E
NG (to lane departure warning camera CAN branch wire) F
NG (to No. 2 CAN junction connector CAN main wire) G



A

REPLACE NO. 1 CAN JUNCTION CONNECTOR

B

29.CONNECT CONNECTOR

C

31.CONNECT CONNECTOR

D

33.CONNECT CONNECTOR

E

35.CONNECT CONNECTOR

F

37.CONNECT CONNECTOR

G

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

29.CONNECT CONNECTOR
a.

Reconnect all wire harness No. 1 CAN junction connectors.

Result:
Proceed to
NEXT




NEXT

30.CHECK FOR SHORT TO GND IN CAN BUS WIRE (SKID CONTROL ECU)
30.CHECK FOR SHORT TO GND IN CAN BUS WIRE (SKID CONTROL ECU)
a.
C235295
1.5,0.073 1.917,0.344 0.417,0.271 0.385,2.583 0.802,2.854 0.417,0.271 1.188,2.083 1.385,2.083 1.385,2.083 1.646,2.469 true 1.365,1.115 0.74,0.729 0.74,0.729 0.542,0.729 true 1.385,1.198 0.979,1.76 0.979,1.76 0.708,1.76 true 1.583,0.115 2.031,0.354 0.448,0.24 10 false A64 0.073,0.208 0.385,0.365 0.313,0.156 10 false *a 0.104,2.146 0.417,2.302 0.313,0.156 10 false *b 0.438,2.635 0.813,2.844 0.375,0.208 10 false G14 0.917,2.01 1.354,2.219 0.438,0.208 10 false CG 0.302,1.688 0.813,1.896 0.51,0.208 10 false CANH 0.167,0.667 0.677,0.875 0.51,0.208 10 false CANL
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])
*b Front view of DLC3


Disconnect the brake actuator assembly (skid control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A64-25 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
A64-14 (CANL) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SKID CONTROL ECU (CANH, CANL)

31.CONNECT CONNECTOR
a.

Reconnect all wire harness No. 1 CAN junction connectors.

Result:
Proceed to
NEXT




NEXT

32.CHECK FOR SHORT TO GND IN CAN BUS WIRE (POWER STEERING ECU ASSEMBLY)
32.CHECK FOR SHORT TO GND IN CAN BUS WIRE (POWER STEERING ECU ASSEMBLY)
a.
C278758
0.448,2.542 0.844,2.792 0.396,0.25 2.323,1.052 2.719,1.302 0.396,0.25 1.073,0.927 1.229,0.927 1.229,0.927 1.469,1.125 true 1.146,1.646 1.302,1.646 1.302,1.646 1.49,1.302 true 1.677,2.438 1.458,2.021 1.458,2.021 1.25,2.021 true 0.115,0.083 0.427,0.24 0.313,0.156 10 *a 0.188,2.01 0.5,2.167 0.313,0.156 10 *b 2.438,1.094 2.75,1.25 0.313,0.156 10 h1 0.5,2.583 0.833,2.833 0.333,0.25 10 G14 0.979,1.927 1.313,2.177 0.333,0.25 10 CG 0.667,0.833 1.167,1.083 0.5,0.25 10 CANH 0.75,1.583 1.25,1.833 0.5,0.25 10 CANL
*a Rear view of wire harness connector
(to Power Steering ECU Assembly)
*b Front view of DLC3


Disconnect the power steering ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
h1-4 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
h1-8 (CANL) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER STEERING ECU ASSEMBLY (CANH, CANL)

33.CONNECT CONNECTOR
a.

Reconnect all wire harness No. 1 CAN junction connectors.

Result:
Proceed to
NEXT




NEXT

34.CHECK FOR SHORT TO GND IN CAN BUS WIRE (STEERING ANGLE SENSOR)
34.CHECK FOR SHORT TO GND IN CAN BUS WIRE (STEERING ANGLE SENSOR)
a.
C278759
0.438,2.542 0.854,2.792 0.417,0.25 0.5,0.979 0.917,1.229 0.417,0.25 1.167,1.75 1.333,1.75 1.333,1.75 1.583,1.333 true 1.281,2.083 1.51,2.083 1.51,2.083 1.667,2.417 true 1.729,1.333 2,1.75 2,1.75 2.167,1.75 true 0.083,0.094 0.396,0.25 0.313,0.156 10 *a 0.104,2 0.417,2.156 0.313,0.156 10 *b 0.583,1.021 0.917,1.26 0.333,0.24 10 G12 0.5,2.583 0.833,2.823 0.333,0.24 10 G14 0.75,1.667 1.25,1.906 0.5,0.24 10 CANL 2.219,1.677 2.719,1.917 0.5,0.24 10 CANH 1.042,2.01 1.542,2.25 0.5,0.24 10 CG
*a Front view of wire harness connector
(to Spiral with Sensor Cable Sub-assembly [Steering Angle Sensor])
*b Front view of DLC3


Disconnect the spiral with sensor cable sub-assembly (steering angle sensor) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G12-3 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G12-2 (CANL) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO STEERING ANGLE SENSOR (CANH, CANL)

35.CONNECT CONNECTOR
a.

Reconnect all wire harness No. 1 CAN junction connectors.

Result:
Proceed to
NEXT




NEXT

36.CHECK FOR SHORT TO GND IN CAN BUS WIRE (MAIN BODY ECU)
36.CHECK FOR SHORT TO GND IN CAN BUS WIRE (MAIN BODY ECU)
a.
C206323
0.354,2.625 0.771,2.875 0.417,0.25 0.417,1 0.833,1.25 0.417,0.25 1.302,2.115 1.521,2.115 1.521,2.115 1.698,2.479 true 0.99,0.333 1.323,0.333 1.323,0.333 1.635,1.083 true 0.813,0.583 1.063,0.583 1.063,0.583 1.563,1.083 true 0.083,0.083 0.417,0.25 0.333,0.167 10 false *a 0.167,2.083 0.479,2.24 0.313,0.156 10 false *b 0.438,2.667 0.833,2.917 0.396,0.25 10 false G14 0.49,1.052 0.885,1.302 0.396,0.25 10 false G78 0.583,0.25 1.083,0.5 0.5,0.25 10 false CANL 0.375,0.5 0.896,0.729 0.521,0.229 10 false CANH 1.042,2.031 1.542,2.281 0.5,0.25 10 false CG
*a Rear view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU])
*b Front view of DLC3


Disconnect the main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G78-14 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G78-13 (CANL) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MAIN BODY ECU (CANH, CANL)

37.CONNECT CONNECTOR
a.

Reconnect all wire harness No. 1 CAN junction connectors.

Result:
Proceed to
NEXT




NEXT

38.CHECK FOR SHORT TO GND IN CAN BUS WIRE (LANE DEPARTURE WARNING CAMERA)
38.CHECK FOR SHORT TO GND IN CAN BUS WIRE (LANE DEPARTURE WARNING CAMERA)
a.
C267485
0.563,1.063 0.99,1.344 0.427,0.281 0.396,2.542 0.823,2.823 0.427,0.281 1.208,2.083 1.427,2.083 1.427,2.083 1.646,2.479 true 2.073,1.406 2.219,1.615 2.219,1.615 2.438,1.615 true 2.063,1.135 2.208,0.958 2.208,0.958 2.427,0.958 true 0.083,0.083 0.396,0.25 0.313,0.167 10 *a 0.167,2.094 0.479,2.25 0.313,0.156 10 *b 0.969,2 1.323,2.188 0.354,0.188 10 CG 0.469,2.615 0.823,2.802 0.354,0.188 10 G14 0.635,1.115 0.99,1.302 0.354,0.188 10 Q13 2.5,1.531 2.969,1.719 0.469,0.188 10 CA1N 2.5,0.885 2.969,1.073 0.469,0.188 10 CA1P
*a Front view of wire harness connector
(to Lane Departure Warning Camera)
*b Front view of DLC3


Disconnect the lane departure warning camera connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q13-6 (CA1P) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
Q13-12 (CA1N) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO LANE DEPARTURE WARNING CAMERA (CA1P, CA1N)

39.CHECK FOR SHORT TO GND IN CAN BUS WIRE (DLC3 CAN BRANCH WIRE)
a.
C253362
0.146,1.125 0.542,1.365 0.396,0.24 1.958,0.917 2.333,0.417 2.333,0.417 2.583,0.417 true 1.948,1.49 1.625,1.917 1.625,1.917 1.375,1.917 true 1.563,0.906 1.292,0.531 1.292,0.531 1.052,0.531 true 0.208,1.167 0.479,1.333 0.271,0.167 10 G14 0.094,0.115 0.365,0.281 0.271,0.167 10 *a 2.625,0.333 3.094,0.5 0.469,0.167 10 CANH 0.948,1.833 1.417,2 0.469,0.167 10 CANL 0.823,0.458 1.156,0.708 0.333,0.25 10 CG
*a Front view of DLC3


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the G134 No. 4 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G14-6 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G14-14 (CANL) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

40.CONNECT CONNECTOR

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)

40.CONNECT CONNECTOR
a.

Reconnect the No. 4 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

41.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 21 CAN JUNCTION CONNECTOR SIDE)
41.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 21 CAN JUNCTION CONNECTOR SIDE)
a.
C253362
0.146,1.125 0.542,1.365 0.396,0.24 1.958,0.917 2.333,0.417 2.333,0.417 2.583,0.417 true 1.948,1.49 1.625,1.917 1.625,1.917 1.375,1.917 true 1.563,0.906 1.292,0.531 1.292,0.531 1.052,0.531 true 0.208,1.167 0.479,1.333 0.271,0.167 10 G14 0.094,0.115 0.365,0.281 0.271,0.167 10 *a 2.625,0.333 3.094,0.5 0.469,0.167 10 CANH 0.948,1.833 1.417,2 0.469,0.167 10 CANL 0.823,0.458 1.156,0.708 0.333,0.25 10 CG
*a Front view of DLC3


Disconnect the A72 No. 21 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G14-6 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G14-14 (CANL) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

42.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 21 CAN JUNCTION CONNECTOR)

NG

45.CONNECT CONNECTOR
42.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 21 CAN JUNCTION CONNECTOR)
a.
C227517
0.385,1.135 0.76,1.396 0.375,0.26 0.385,2.51 0.76,2.771 0.375,0.26 1.167,2.104 1.365,2.104 1.365,2.104 1.635,2.469 true 2.25,1.333 2.396,1.563 2.396,1.563 2.594,1.563 true 2.135,1.333 2.25,1.813 2.25,1.813 2.448,1.813 true 2.229,1.177 2.406,0.958 2.406,0.958 2.604,0.958 true 2.125,1.198 2.365,0.583 2.365,0.583 2.563,0.583 true 0.094,0.052 0.406,0.208 0.313,0.156 10 false *a 0.115,2.063 0.427,2.219 0.313,0.156 10 false *b 2.667,0.854 3.24,1.094 0.573,0.24 10 false CANH*c 2.604,0.469 3.219,0.74 0.615,0.271 10 false CANH*d 0.917,2 1.323,2.26 0.406,0.26 10 false CG 2.656,1.458 3.229,1.698 0.573,0.24 10 false CANL*c 2.51,1.708 3.125,1.979 0.615,0.271 10 false CANL*d 0.438,2.552 0.771,2.792 0.333,0.24 10 false G14 0.448,1.177 0.781,1.417 0.333,0.24 10 false A72
*a Rear view of wire harness connector
(to No. 21 CAN Junction Connector)
*b Front view of DLC3
*c to Brake Actuator Assembly (Skid Control ECU)
*d to ECM


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A72-1 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
A72-12 (CANL) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
A72-2 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
A72-13 (CANL) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Result Proceed to
OK A
NG (to brake actuator assembly [skid control ECU] CAN branch wire) B
NG (to ECM CAN main wire) C



A

REPLACE NO. 21 CAN JUNCTION CONNECTOR

B

43.CONNECT CONNECTOR

C

44.CONNECT CONNECTOR
43.CONNECT CONNECTOR
a.

Reconnect the No. 21 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

30.CHECK FOR SHORT TO GND IN CAN BUS WIRE (SKID CONTROL ECU)
44.CONNECT CONNECTOR
a.

Reconnect the No. 21 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

7.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECM)
45.CONNECT CONNECTOR
a.

Reconnect the No. 21 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

46.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR)
46.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR)
a.
C227517
0.333,2.604 0.74,2.875 0.406,0.271 1.427,0.063 1.833,0.333 0.406,0.271 1.302,2.198 1.479,2.198 1.479,2.198 1.656,2.479 true 2.24,1.344 2.375,1.49 2.375,1.49 2.573,1.49 true 2.135,1.344 2.344,1.646 2.344,1.646 2.51,1.646 true 2.24,1.177 2.406,0.958 2.406,0.958 2.604,0.958 true 2.135,1.156 2.406,0.74 2.406,0.74 2.594,0.74 true 2.021,1.188 2.333,0.49 2.333,0.49 2.521,0.49 true 2.031,1.323 2.302,1.854 2.302,1.854 2.469,1.854 true 1.917,1.177 2.271,0.281 2.271,0.281 2.458,0.281 true 1.823,1.177 2.125,0.083 2.125,0.083 2.313,0.083 true 1.917,1.313 2.198,2.021 2.198,2.021 2.365,2.021 true 2.229,2.167 2.063,2.167 2.063,2.167 1.802,1.344 true 0.865,1.521 1,1.521 1,1.521 1.177,1.333 true 0.854,0.979 1.031,0.979 1.031,0.979 1.198,1.188 true 0.833,0.688 1.01,0.688 1.01,0.688 1.406,1.198 true 0.927,1.719 1.104,1.719 1.104,1.719 1.396,1.333 true 1.073,1.885 1.25,1.885 1.25,1.885 1.51,1.313 true 0.854,0.5 1.031,0.5 1.031,0.5 1.51,1.177 true 0.094,0.052 0.406,0.208 0.313,0.156 10 false *a 0.115,2.063 0.427,2.219 0.313,0.156 10 false *b 2.667,0.854 3.24,1.094 0.573,0.24 10 false CANH*c 2.646,0.625 3.26,0.896 0.615,0.271 10 false CANH*d 1.052,2.083 1.458,2.344 0.406,0.26 10 false CG 2.625,1.385 3.198,1.625 0.573,0.24 10 false CANL*c 2.573,1.552 3.188,1.823 0.615,0.271 10 false CANL*d 0.406,2.646 0.813,2.906 0.406,0.26 10 false G14 1.469,0.104 1.875,0.365 0.406,0.26 10 false G134 2.521,1.76 3.135,2.031 0.615,0.271 10 false CANL*e 2.563,0.406 3.177,0.677 0.615,0.271 10 false CANH*e 2.51,0.198 3.125,0.469 0.615,0.271 10 false CANH*f 2.365,0.021 2.979,0.292 0.615,0.271 10 false CANH*g 2.406,1.927 3.021,2.198 0.615,0.271 10 false CANL*f 2.271,2.094 2.885,2.365 0.615,0.271 10 false CANL*g 0.365,1.417 0.979,1.688 0.615,0.271 10 false CANL*j 0.323,0.885 0.938,1.156 0.615,0.271 10 false CANH*j 0.333,0.625 0.948,0.896 0.615,0.271 10 false CANH*i 0.438,1.615 1.052,1.885 0.615,0.271 10 false CANL*i 0.313,0.406 0.927,0.677 0.615,0.271 10 false CANH*h 0.542,1.802 1.156,2.073 0.615,0.271 10 false CANL*h
*a Rear view of wire harness connector
(to No. 4 CAN Junction Connector)
*b Front view of DLC3
*c to Airbag Sensor Assembly
*d to Air Conditioning Amplifier Assembly
*e to Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor)
*f to Power Steering ECU Assembly
*g to Main Body ECU (Multiplex Network Body ECU)
*h to 4WD ECU Assembly
*i to Combination Meter Assembly
*j to No. 21 CAN Junction Connector


Disconnect the No. 4 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G134-1 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G134-12 (CANL) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G134-2 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G134-13 (CANL) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G134-3 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G134-14 (CANL) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G134-4 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G134-15 (CANL) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G134-5 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G134-16 (CANL) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G134-8 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G134-19 (CANL) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G134-9 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G134-20 (CANL) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G134-11 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G134-22 (CANL) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Result Proceed to
OK A
NG (to airbag sensor assembly CAN branch wire) B
NG (to spiral with sensor cable sub-assembly [steering angle sensor] CAN branch wire) C
NG (to power steering ECU assembly CAN branch wire) D
NG (to main body ECU [multiplex network body ECU] CAN branch wire) E
NG (to 4WD ECU assembly CAN branch wire) F
NG (to combination meter assembly CAN main wire) G
NG (to air conditioning amplifier assembly CAN branch wire) H
NG (to No. 21 CAN junction connector CAN main wire) I



A

REPLACE NO. 4 CAN JUNCTION CONNECTOR

B

47.CONNECT CONNECTOR

C

48.CONNECT CONNECTOR

D

49.CONNECT CONNECTOR

E

50.CONNECT CONNECTOR

F

51.CONNECT CONNECTOR

G

52.CONNECT CONNECTOR

H

53.CONNECT CONNECTOR

I

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - NO. 21 CAN JUNCTION CONNECTOR)

47.CONNECT CONNECTOR
a.

Reconnect the No. 4 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

26.CHECK FOR SHORT TO GND IN CAN BUS WIRE (AIRBAG SENSOR ASSEMBLY)
48.CONNECT CONNECTOR
a.

Reconnect the No. 4 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

34.CHECK FOR SHORT TO GND IN CAN BUS WIRE (STEERING ANGLE SENSOR)
49.CONNECT CONNECTOR
a.

Reconnect the No. 4 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

32.CHECK FOR SHORT TO GND IN CAN BUS WIRE (POWER STEERING ECU ASSEMBLY)
50.CONNECT CONNECTOR
a.

Reconnect the No. 4 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

36.CHECK FOR SHORT TO GND IN CAN BUS WIRE (MAIN BODY ECU)
51.CONNECT CONNECTOR
a.

Reconnect the No. 4 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

22.CHECK FOR SHORT TO GND IN CAN BUS WIRE (4WD ECU ASSEMBLY)
52.CONNECT CONNECTOR
a.

Reconnect the No. 4 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

18.CHECK FOR SHORT TO GND IN CAN BUS WIRE (COMBINATION METER ASSEMBLY)
53.CONNECT CONNECTOR
a.

Reconnect the No. 4 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

54.CHECK FOR SHORT TO GND IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY)
54.CHECK FOR SHORT TO GND IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.
C281143
0.302,2.49 0.729,2.75 0.427,0.26 0.229,0.896 0.656,1.156 0.427,0.26 1.635,2.365 1.448,2.021 1.448,2.021 1.25,2.021 true 1.052,0.948 0.875,0.615 0.875,0.615 0.698,0.615 true 1.156,0.969 0.917,0.302 0.917,0.302 0.74,0.302 true 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 0.104,2.042 0.417,2.198 0.313,0.156 10 false *b 0.313,0.948 0.708,1.177 0.396,0.229 10 false G80 0.333,0.198 0.854,0.417 0.521,0.219 10 false CANH 0.323,0.531 0.844,0.75 0.521,0.219 10 false CANL 1.01,1.927 1.531,2.146 0.521,0.219 10 false CG 0.375,2.542 0.896,2.76 0.521,0.219 10 false G14
*a Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly)
*b Front view of DLC3


Disconnect the air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G80-8 (CANH) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G80-9 (CANL) - G14-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIR CONDITIONING AMPLIFIER ASSEMBLY (CANH, CANL)