Home › Vehicle Exterior › DOOR / HATCH › BACK DOOR
RM30B0U _59 Vehicle Exterior _009875 DOOR / HATCH _0054296 BACK DOOR A

DOOR / HATCH  BACK DOOR  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



PROCEDURE

Hide 1.INSTALL BACK DOOR PANEL CUSHION

a.

Attach the 2 claws to install the 2 new back door panel cushions.


b.

Connect the connector and detach the clamp.


Hide 2.INSTALL BACK DOOR DAMPER STAY LOWER BRACKET LH (w/o Power Back Door)

Hide 3.INSTALL BACK DOOR DAMPER STAY LOWER BRACKET RH (w/o Power Back Door)

HINT:

Use the same procedure as for the LH side.


Hide 4.INSTALL BACK DOOR DAMPER STAY UPPER BRACKET LH (w/o Power Back Door)

Hide 5.INSTALL BACK DOOR DAMPER STAY UPPER BRACKET RH (w/o Power Back Door)

HINT:

Use the same procedure as for the LH side.


Hide 6.INSTALL BACK DOOR STAY ASSEMBLY LH (w/o Power Back Door)

Hide 7.INSTALL BACK DOOR STAY ASSEMBLY RH (w/o Power Back Door)

HINT:

Use the same procedure as for the LH side.


Hide 8.INSTALL POWER BACK DOOR UNIT ASSEMBLY SET LH (w/ Power Back Door)

Hide 9.INSTALL POWER BACK DOOR UNIT ASSEMBLY SET RH (w/ Power Back Door)

HINT:

Use the same procedure as for the LH side.


Hide 10.INSTALL LICENSE PLATE LIGHT ASSEMBLY LH

Hide 11.INSTALL LICENSE PLATE LIGHT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 12.INSTALL TELEVISION CAMERA ASSEMBLY (w/ Television Camera)

Click here

Hide 13.INSTALL BACK DOOR OPENER SWITCH ASSEMBLY

Hide 14.INSTALL BACK DOOR OUTSIDE GARNISH SUB-ASSEMBLY

Hide 15.INSTALL REAR WASHER NOZZLE SUB-ASSEMBLY

Hide 17.INSTALL BACK DOOR GLASS CHANNEL LH

Hide 18.INSTALL BACK DOOR GLASS CHANNEL RH

HINT:

Use the same procedure as for the LH side.


Hide 19.INSTALL REAR LIGHT ASSEMBLY LH

Hide 20.INSTALL REAR LIGHT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 21.INSTALL POWER BACK DOOR SENSOR ASSEMBLY LH (w/ Power Back Door)

Hide 22.INSTALL POWER BACK DOOR SENSOR ASSEMBLY RH (w/ Power Back Door)

HINT:

Use the same procedure as for the LH side.


Hide 23.INSTALL REAR WIPER MOTOR ASSEMBLY

Hide 24.INSTALL NO. 1 REAR WIPER LINK PIVOT WASHER

Hide 25.INSTALL REAR WIPER ARM AND BLADE ASSEMBLY

Hide 26.INSTALL REAR WIPER ARM COVER

Hide 27.INSTALL MULTIPLEX NETWORK DOOR ECU (w/ Power Back Door)

Hide 28.INSTALL WIRELESS DOOR LOCK BUZZER (w/ Power Back Door)

Hide 29.INSTALL BACK DOOR LOCK ASSEMBLY

Hide 30.INSTALL DOOR CONTROL SWITCH ASSEMBLY (w/ Power Back Door)

Hide 31.INSTALL DOOR PULL HANDLE

a.

Attach the 4 claws to install the door pull handle.


Hide 32.INSTALL BACK DOOR NO. 1 SERVICE HOLE COVER

a.

Attach the 4 claws and 4 guides to install the back door No. 1 service hole cover.


Hide 33.INSTALL BACK DOOR NO. 2 SERVICE HOLE COVER

a.

Attach the 2 claws and 2 guides to install the back door No. 2 service hole cover.


Hide 34.INSTALL BACK DOOR SERVICE HOLE COVER LH

a.

Attach the 2 claws and 2 guides to install the back door service hole cover LH.


Hide 35.INSTALL BACK DOOR SERVICE HOLE COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 36.INSTALL BACK DOOR TRIM BOARD ASSEMBLY

a.

Attach the 13 clips to install the back door trim board assembly.


Hide 37.INSTALL BACK DOOR SIDE GARNISH LH

a.

Attach the 2 claws and 2 clips to install the back door side garnish LH.


Hide 38.INSTALL BACK DOOR SIDE GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 39.INSTALL BACK DOOR CENTER GARNISH

a.

Attach the 4 claws and 4 clips to install the back door center garnish.