Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD) › 2012.12–2013.11
RM3090E _57 Power Source / Network _008434 NETWORKING _0050193 CAN COMMUNICATION SYSTEM(for RHD) J

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD)  Short to B+ in CAN Bus Line  


DESCRIPTION

There may be a short circuit between the CAN bus lines and +B when the resistance between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of the DLC3 is below 6 kΩ.

Symptom Trouble Area

*1: w/ Blind Spot Monitor System

*2: w/ Stop and Start System

*3: for Radio and Display Type

*4: for Navigation Receiver Type

*5: for 4WD/AWD

*6: w/ Entry and Start System

The resistance between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of the DLC3 is below 6 kΩ.
·

Short between CAN bus lines and +B

·

ECM

·

Blind spot monitor sensor LH*1

·

Brake actuator assembly (skid control ECU)

·

Power steering ECU assembly

·

Main body ECU (multiplex network body ECU)

·

Air conditioning amplifier assembly

·

Engine stop and start ECU*2

·

Radio and display receiver assembly*3

·

Navigation ECU sub-assembly*4

·

4WD ECU assembly*5

·

Certification ECU (smart key ECU assembly)*6

·

Spiral with sensor cable sub-assembly (steering angle sensor)

·

Airbag sensor assembly

·

Combination meter assembly

·

No. 1 CAN junction connector

·

No. 2 CAN junction connector

·

No. 3 CAN junction connector

·

DLC3 CAN branch wire or connector



WIRING DIAGRAM

C279372E02
6.219,1.469 6.677,1.667 0.458,0.198 10 false ECM 6.01,1.177 6.469,1.375 0.458,0.198 10 false CANL 6.01,0.417 6.469,0.615 0.458,0.198 10 false CANH 5.135,0.531 5.594,0.729 0.458,0.198 10 false A62 5.135,1.063 5.594,1.26 0.458,0.198 10 false A62 5.594,0.531 6.052,0.729 0.458,0.198 10 false A61 5.583,1.052 6.042,1.25 0.458,0.198 10 false A61 5.604,0.813 6.063,1.01 0.458,0.198 10 false 6*2 5.604,0.271 6.063,0.469 0.458,0.198 10 false 7*2 5.146,0.271 5.604,0.469 0.458,0.198 10 false 13*1 5.146,0.813 5.604,1.01 0.458,0.198 10 false 26*1 3.906,1.063 4.365,1.26 0.458,0.198 10 false N27 3.896,0.531 4.354,0.729 0.458,0.198 10 false N27 3.958,0.292 4.417,0.49 0.458,0.198 10 false 1 3.958,0.823 4.417,1.021 0.458,0.198 10 false 2 3.969,2.396 4.427,2.594 0.458,0.198 10 false 2 3.969,1.875 4.427,2.073 0.458,0.198 10 false 1 3.885,2.115 4.344,2.313 0.458,0.198 10 false N28 3.896,2.646 4.354,2.844 0.458,0.198 10 false N28 2.75,1.052 3.208,1.25 0.458,0.198 10 false N29 2.833,0.802 3.292,1 0.458,0.198 10 false 2 2.833,0.292 3.292,0.49 0.458,0.198 10 false 1 2.75,0.521 3.208,0.719 0.458,0.198 10 false N29 1.25,0.417 1.708,0.615 0.458,0.198 10 false 2 1.25,0.938 1.708,1.135 0.458,0.198 10 false 7 0.75,0.542 1.208,0.74 0.458,0.198 10 false CA1P 0.75,1.042 1.208,1.24 0.458,0.198 10 false CA1N 0.188,1.427 0.646,1.625 0.458,0.198 10 false R1 0.198,1.594 2.25,1.833 2.052,0.24 10 false Blind Spot Monitor Sensor LH*3 2.531,3.063 4.458,3.5 1.927,0.438 10 false No. 3 CAN Junction Connector 3.594,8.167 6.083,8.417 2.49,0.25 10 false No. 1 CAN Junction Connector 6.031,6.125 6.49,6.323 0.458,0.198 10 false CANH 6.031,6.646 6.49,6.844 0.458,0.198 10 false CANL 2.823,3.771 3.281,3.969 0.458,0.198 10 false 1 3.969,3.75 4.427,3.948 0.458,0.198 10 false 1 3.969,5.875 4.427,6.073 0.458,0.198 10 false 1 2.823,5.875 3.281,6.073 0.458,0.198 10 false 1 3.979,4.292 4.438,4.49 0.458,0.198 10 false 2 2.833,4.292 3.292,4.49 0.458,0.198 10 false 2 2.833,6.396 3.292,6.594 0.458,0.198 10 false 2 3.979,6.396 4.438,6.594 0.458,0.198 10 false 2 5.74,6 6.198,6.198 0.458,0.198 10 false 14 5.74,6.521 6.198,6.719 0.458,0.198 10 false 13 3.854,4 4.313,4.198 0.458,0.198 10 false G118 3.854,4.521 4.313,4.719 0.458,0.198 10 false G118 2.708,4 3.167,4.198 0.458,0.198 10 false G120 2.708,4.521 3.167,4.719 0.458,0.198 10 false G120 1.25,3.896 1.708,4.094 0.458,0.198 10 false 25 1.25,4.427 1.708,4.625 0.458,0.198 10 false 14 0.74,3.99 1.198,4.188 0.458,0.198 10 false CANH 0.75,4.531 1.208,4.729 0.458,0.198 10 false CANL 3.865,6.115 4.323,6.313 0.458,0.198 10 false G123 3.854,6.646 4.313,6.844 0.458,0.198 10 false G123 2.708,6.115 3.167,6.313 0.458,0.198 10 false G124 2.698,6.635 3.156,6.833 0.458,0.198 10 false G124 0.188,4.896 2.24,5.135 2.052,0.24 10 false A64 0.188,5.063 1.813,5.438 1.625,0.375 10 false Brake Actuator Assembly (Skid Control ECU) 0.469,7.031 2.521,7.271 2.052,0.24 10 false G14 0.49,7.188 1.031,7.417 0.542,0.229 10 false DLC3 0.76,6.115 1.219,6.313 0.458,0.198 10 false CANH 0.771,6.625 1.229,6.823 0.458,0.198 10 false CANL 1.25,6.021 1.708,6.219 0.458,0.198 10 false 6 1.26,6.531 1.719,6.729 0.458,0.198 10 false 14 5.375,7.01 6.594,7.167 1.219,0.156 10 false G78 5.375,7.188 7.052,7.552 1.677,0.365 10 false Main Body ECU (Multiplex Network Body ECU) 0.167,7.875 2.583,8.333 2.417,0.458 10 false *1: for 2AR-FE, 3ZR-FAE, 3ZR-FE 0.167,8.167 3.417,8.417 3.25,0.25 10 false *2: for 1AD-FTV, 2AD-FHV, 2AD-CCo, 2AD-DPF 0.167,8.5 3.417,8.75 3.25,0.25 10 false *3: w/ Blind Spot Monitor System

C281177E01
3.813,1.24 4.427,1.438 0.615,0.198 10 false G125 3.823,0.719 4.438,0.917 0.615,0.198 10 false G125 2.677,0.719 3.292,0.917 0.615,0.198 10 false G126 2.667,1.229 3.281,1.427 0.615,0.198 10 false G126 2.667,2.823 3.281,3.021 0.615,0.198 10 false G127 2.667,3.354 3.281,3.552 0.615,0.198 10 false G127 3.823,3.354 4.438,3.552 0.615,0.198 10 false G119 3.823,2.833 4.438,3.031 0.615,0.198 10 false G119 1.26,1.229 1.875,1.427 0.615,0.198 10 false G81 1.719,1.229 2.333,1.427 0.615,0.198 10 false G80 1.708,0.719 2.323,0.917 0.615,0.198 10 false G80 1.271,0.719 1.885,0.917 0.615,0.198 10 false G81 0.688,0.729 1.302,0.927 0.615,0.198 10 false CANH 6.01,0.719 6.625,0.917 0.615,0.198 10 false CANH 6.01,1.229 6.625,1.427 0.615,0.198 10 false CANL 0.688,1.24 1.302,1.438 0.615,0.198 10 false CANL 0.688,3.375 1.302,3.573 0.615,0.198 10 false CANL 0.677,2.844 1.292,3.042 0.615,0.198 10 false CANH 6.01,6.833 6.625,7.031 0.615,0.198 10 false CANH 6.01,7.375 6.625,7.573 0.615,0.198 10 false CANL 0.667,4.74 1.281,4.938 0.615,0.198 10 false CANH 0.635,6.813 1.25,7.01 0.615,0.198 10 false CANH 0.698,5.24 1.313,5.438 0.615,0.198 10 false CANL 0.656,7.344 1.271,7.542 0.615,0.198 10 false CANL 2.51,3.969 5.063,4.219 2.552,0.25 10 false No. 1 CAN Junction Connector 3.938,8.531 6.49,8.781 2.552,0.25 10 false No. 2 CAN Junction Connector 3.823,4.708 4.438,4.906 0.615,0.198 10 false G129 3.823,5.24 4.438,5.438 0.615,0.198 10 false G129 2.667,4.708 3.281,4.906 0.615,0.198 10 false G155 2.667,5.229 3.281,5.427 0.615,0.198 10 false G155 3.813,6.823 4.427,7.021 0.615,0.198 10 false G156 3.823,7.344 4.438,7.542 0.615,0.198 10 false G156 2.667,6.823 3.281,7.021 0.615,0.198 10 false G130 2.667,7.344 3.281,7.542 0.615,0.198 10 false G130 1.219,7.354 1.833,7.552 0.615,0.198 10 false G143 1.219,6.813 1.833,7.01 0.615,0.198 10 false G143 1.688,6.823 2.302,7.021 0.615,0.198 10 false G138 1.667,7.354 2.281,7.552 0.615,0.198 10 false G138 3.917,0.5 4.531,0.698 0.615,0.198 10 false 1 2.781,0.5 3.396,0.698 0.615,0.198 10 false 1 2.792,2.615 3.406,2.813 0.615,0.198 10 false 1 3.938,2.604 4.552,2.802 0.615,0.198 10 false 1 3.948,4.479 4.563,4.677 0.615,0.198 10 false 1 2.813,4.479 3.427,4.677 0.615,0.198 10 false 1 2.792,6.573 3.406,6.771 0.615,0.198 10 false 1 3.938,6.594 4.552,6.792 0.615,0.198 10 false 1 3.938,7.115 4.552,7.313 0.615,0.198 10 false 2 2.781,7.135 3.396,7.333 0.615,0.198 10 false 2 2.802,4.99 3.417,5.188 0.615,0.198 10 false 2 3.938,5 4.552,5.198 0.615,0.198 10 false 2 3.938,3.146 4.552,3.344 0.615,0.198 10 false 2 2.802,3.125 3.417,3.323 0.615,0.198 10 false 2 2.802,1.01 3.417,1.208 0.615,0.198 10 false 2 3.938,1.031 4.552,1.229 0.615,0.198 10 false 2 5.698,0.625 6.313,0.823 0.615,0.198 10 false 13 5.698,1.135 6.313,1.333 0.615,0.198 10 false 22 1.25,0.479 1.865,0.677 0.615,0.198 10 false 11*4 1.229,1 1.844,1.198 0.615,0.198 10 false 12*4 1.74,1.01 2.354,1.208 0.615,0.198 10 false 9*5 1.74,0.49 2.354,0.688 0.615,0.198 10 false 8*5 1.229,2.719 1.844,2.917 0.615,0.198 10 false 15 1.229,3.25 1.844,3.448 0.615,0.198 10 false 16 1.219,4.594 1.833,4.792 0.615,0.198 10 false 4 1.229,5.135 1.844,5.333 0.615,0.198 10 false 8 5.76,6.719 6.375,6.917 0.615,0.198 10 false 3 5.771,7.25 6.385,7.448 0.615,0.198 10 false 2 0.156,1.625 1.708,2.01 1.552,0.385 10 false Air Conditioning Amplifier Assembly 5.563,1.615 6.938,1.958 1.375,0.344 10 false G92 5.563,1.792 7.115,2.156 1.552,0.365 10 false Airbag Sensor Assembly 0.115,3.75 2.208,4.042 2.094,0.292 10 false G87 0.125,3.917 2.219,4.208 2.094,0.292 10 false Engine Stop and Start ECU*6 0.125,5.615 2.219,5.906 2.094,0.292 10 false h1 0.125,5.781 2.219,6.073 2.094,0.292 10 false Power Steering ECU Assembly 4.573,7.719 6.667,8.01 2.094,0.292 10 false G12 4.583,7.875 7.031,8.26 2.448,0.385 10 false Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor) 0.094,7.771 2.542,8.156 2.448,0.385 10 false Radio and Display Receiver Assembly*7 1.313,6.604 1.927,6.802 0.615,0.198 10 false 9*7 1.229,7.104 1.844,7.302 0.615,0.198 10 false 10*7 1.698,7.104 2.313,7.302 0.615,0.198 10 false 10*8 1.74,6.583 2.354,6.781 0.615,0.198 10 false 9*8 0.083,8.083 2.531,8.469 2.448,0.385 10 false Navigation ECU Sub-assembly*8 0.135,8.906 3.333,9.25 3.198,0.344 10 false *4: for Automatic Air Conditioning System 0.125,9.219 3.323,9.563 3.198,0.344 10 false *5: for Manual Air Conditioning System 0.146,9.531 3.344,9.875 3.198,0.344 10 false *6: w/ Stop and Start System 2.969,8.938 6.167,9.281 3.198,0.344 10 false *7: for Radio and Display Type 2.969,9.26 6.167,9.604 3.198,0.344 10 false *8: for Navigation Receiver Type

C278784E01
2.542,3.813 4.5,4.083 1.958,0.271 10 No. 2 CAN Junction Connector 3.865,2.896 4.323,3.167 0.458,0.271 10 G128 3.865,3.417 4.323,3.688 0.458,0.271 10 G128 3.99,3.188 4.448,3.458 0.458,0.271 10 2 3.979,2.646 4.438,2.917 0.458,0.271 10 1 3.99,0.563 4.448,0.833 0.458,0.271 10 1 2.833,0.563 3.292,0.833 0.458,0.271 10 1 4,1.083 4.458,1.354 0.458,0.271 10 2 2.833,1.083 3.292,1.354 0.458,0.271 10 2 3.875,0.781 4.333,1.052 0.458,0.271 10 G131 3.875,1.302 4.333,1.573 0.458,0.271 10 G131 2.729,1.302 3.188,1.573 0.458,0.271 10 G132 2.719,0.781 3.177,1.052 0.458,0.271 10 G132 0.708,0.802 1.25,1.052 0.542,0.25 10 CANH 0.75,1.333 1.292,1.583 0.542,0.25 10 CANL 1.292,0.667 1.833,0.917 0.542,0.25 10 14 1.292,1.167 1.833,1.417 0.542,0.25 10 15 0.167,1.667 0.708,1.917 0.542,0.25 10 G84 0.167,1.833 2,2.333 1.833,0.5 10 Certification ECU (Smart Key ECU Assembly)*10 6.052,0.792 6.594,1.042 0.542,0.25 10 CANH 6.052,1.333 6.594,1.583 0.542,0.25 10 CANL 5.823,0.667 6.281,0.938 0.458,0.271 10 6 5.833,1.219 6.292,1.49 0.458,0.271 10 5 5.75,2.781 6.292,3.031 0.542,0.25 10 32 5.75,3.323 6.292,3.573 0.542,0.25 10 31 6.031,3.531 6.573,3.781 0.542,0.25 10 CANL 6.031,2.792 6.573,3.042 0.542,0.25 10 CANH 5.604,1.667 6.146,1.917 0.542,0.25 10 G86 5.615,1.823 7.104,2.073 1.49,0.25 10 4WD ECU Assembly*9 5.844,3.948 7.083,4.365 1.24,0.417 10 Combination Meter Assembly 5.833,3.781 6.375,4.031 0.542,0.25 10 G16 0.25,4.083 1.521,4.323 1.271,0.24 10 *9: for 4WD/AWD 0.25,4.417 2.354,4.635 2.104,0.219 10 *10: w/ Entry and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

For vehicles with an entry and start system:

Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION

·

The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the Precaution in the SRS.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/o Occupant Classification System)>PRECAUTION

·

When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

·

Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.



PROCEDURE

1.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (DLC3 CAN BRANCH WIRE)
a.
C253362C02
0.146,1.125 0.542,1.365 0.396,0.24 1.958,0.917 2.333,0.417 2.333,0.417 2.583,0.417 true 1.948,1.49 1.625,1.917 1.625,1.917 1.375,1.917 true 2.833,1.833 2.583,1.833 2.583,1.833 2.323,1.458 true 0.208,1.167 0.479,1.333 0.271,0.167 10 G14 0.094,0.115 0.365,0.281 0.271,0.167 10 *a 2.625,0.333 3.094,0.5 0.469,0.167 10 CANH 0.948,1.833 1.417,2 0.469,0.167 10 CANL 2.885,1.75 3.219,2 0.333,0.25 10 BAT
*a Front view of DLC3


Disconnect the G124 No. 1 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G14-6 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G14-14 (CANL) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CONNECT CONNECTOR

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)

2.CONNECT CONNECTOR
a.

Reconnect wire harness No. 1 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

3.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR SIDE)
3.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR SIDE)
a.
C253362C02
0.146,1.125 0.542,1.365 0.396,0.24 1.958,0.917 2.333,0.417 2.333,0.417 2.583,0.417 true 1.948,1.49 1.625,1.917 1.625,1.917 1.375,1.917 true 2.833,1.833 2.583,1.833 2.583,1.833 2.323,1.458 true 0.208,1.167 0.479,1.333 0.271,0.167 10 G14 0.094,0.115 0.365,0.281 0.271,0.167 10 *a 2.625,0.333 3.094,0.5 0.469,0.167 10 CANH 0.948,1.833 1.417,2 0.469,0.167 10 CANL 2.885,1.75 3.219,2 0.333,0.25 10 BAT
*a Front view of DLC3


Disconnect the N28 No. 3 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G14-6 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G14-14 (CANL) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR)

NG

9.CONNECT CONNECTOR
4.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 3 CAN junction connectors.

C278754C05
5.51,2.24 5.958,2.51 0.448,0.271 6.625,3.427 6.396,3.427 6.396,3.427 6.198,3.167 true 3.615,3.271 3.469,3.26 3.469,3.26 3.323,3 true 3.625,2.625 3.458,2.625 3.458,2.625 3.313,2.865 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *1 2.531,2.385 2.844,2.583 0.313,0.198 10 false *a 4.531,2.333 4.844,2.531 0.313,0.198 10 false *b 6.667,3.344 7.052,3.563 0.385,0.219 10 false BAT 3.667,2.552 4.208,2.781 0.542,0.229 10 false CANH 3.677,3.177 4.219,3.406 0.542,0.229 10 false CANL 1.385,2.125 1.927,2.354 0.542,0.229 10 false N29 1.375,1.677 1.917,1.906 0.542,0.229 10 false N27 5.594,2.271 6.135,2.5 0.542,0.229 10 false G14
*1 No. 3 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 3 CAN Junction Connector)
*b Front view of DLC3


Code Color (CANH Side) Color (CANL Side) Connect to

*: w/ Blind Spot Monitor System

N27 Y W ECM
N29 R W Blind Spot Monitor Sensor LH*


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N27-1 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
N27-2 (CANL) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
N29-1 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
N29-2 (CANL) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG (to ECM CAN main wire)
NG (to blind spot monitor sensor LH CAN branch wire)



OK

REPLACE NO. 3 CAN JUNCTION CONNECTOR

NG (to ECM CAN main wire)

5.CONNECT CONNECTOR

NG (to blind spot monitor sensor LH CAN branch wire)

7.CONNECT CONNECTOR
5.CONNECT CONNECTOR
a.

Reconnect all wire harness No. 3 CAN junction connectors.


Result:
Proceed to
NEXT



NEXT

6.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECM)
6.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECM)
a.

Disconnect the ECM connector.


C278755C01
1.198,0.5 1.594,0.75 0.396,0.25 3.323,0.49 3.719,0.74 0.396,0.25 5.708,0.729 6.104,0.979 0.396,0.25 6.406,1.708 6.531,1.979 6.531,1.979 6.698,1.979 true 3.99,1.26 4.219,0.844 4.219,0.844 4.479,0.844 true 3.906,1.25 4.135,0.604 4.135,0.604 4.396,0.604 true 2.125,1.375 2.354,0.896 2.354,0.896 2.552,0.896 true 2.115,1.448 2.344,2.135 2.344,2.135 2.604,2.135 true 1.26,0.542 1.719,0.74 0.458,0.198 10 A62 1.677,0.521 2.135,0.719 0.458,0.198 10 *A 0.156,0.125 0.615,0.323 0.458,0.198 10 *a 5.021,0.146 5.479,0.344 0.458,0.198 10 *b 5.771,0.771 6.229,0.969 0.458,0.198 10 G14 3.396,0.531 3.854,0.729 0.458,0.198 10 A61 3.802,0.531 4.26,0.729 0.458,0.198 10 *B 2.583,0.833 3.042,1.031 0.458,0.198 10 CANH 2.667,2.063 3.125,2.26 0.458,0.198 10 CANL 4.448,0.531 4.906,0.729 0.458,0.198 10 CANL 4.521,0.781 4.979,0.979 0.458,0.198 10 CANH 6.75,1.906 7.115,2.292 0.365,0.385 10 BAT
*A for 2AR-FE, 3ZR-FAE, 3ZR-FE *B for 1AD-FTV, 2AD-FHV, 2AD-CCo, 2AD-DPF
*a Front view of wire harness connector
(to ECM)
*b Front view of DLC3


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 2AR-FE, 3ZR-FAE, 3ZR-FE
Tester Connection Condition Specified Condition
A62-13 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A62-26 (CANL) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

for 1AD-FTV, 2AD-FHV, 2AD-CCo, 2AD-DPF
Tester Connection Condition Specified Condition
A61-7 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A61-6 (CANL) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)

7.CONNECT CONNECTOR
a.

Reconnect all wire harness No. 3 CAN junction connectors.


Result:
Proceed to
NEXT



NEXT

8.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (BLIND SPOT MONITOR SENSOR LH)
8.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (BLIND SPOT MONITOR SENSOR LH)
a.
C268298C01
1.531,1.948 1.948,2.208 0.417,0.26 1.469,0.24 1.885,0.5 0.417,0.26 1.563,1.052 1.188,0.719 1.188,0.719 0.958,0.719 true 1.563,1.198 1.198,1.531 1.198,1.531 0.969,1.531 true 2.198,2.938 2.292,3.219 2.292,3.219 2.542,3.219 true 0.073,0.083 0.385,0.24 0.313,0.156 10 false *a 0.104,1.979 0.417,2.135 0.313,0.156 10 false *b 0.563,0.646 1.042,0.917 0.479,0.271 10 false CA1P 0.573,1.469 1.052,1.74 0.479,0.271 10 false CA1N 2.573,3.135 3.063,3.333 0.49,0.198 10 false BAT 1.573,0.292 1.969,0.469 0.396,0.177 10 false R1 1.604,2 2,2.177 0.396,0.177 10 false G14
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)
*b Front view of DLC3


Disconnect the blind spot monitor sensor LH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R1-2 (CA1P) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
R1-7 (CA1N) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO BLIND SPOT MONITOR SENSOR LH (CA1P, CA1N)

9.CONNECT CONNECTOR
a.

Reconnect wire harness No. 3 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

10.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - NO. 3 CAN JUNCTION CONNECTOR)
10.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - NO. 3 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 1 CAN junction connector.

C253917C01
5.521,2.229 5.927,2.479 0.406,0.25 3.302,2.875 3.469,2.698 3.469,2.698 3.552,2.698 true 3.302,3.01 3.458,3.177 3.458,3.177 3.542,3.177 true 6.219,3.198 6.375,3.365 6.375,3.365 6.458,3.365 true 0.063,0.042 0.375,0.198 0.313,0.156 10 *1 3.604,2.635 4.167,2.844 0.563,0.208 10 CANH 2.521,2.417 2.833,2.573 0.313,0.156 10 *a 4.604,2.344 4.917,2.5 0.313,0.156 10 *b 3.594,3.115 4.156,3.323 0.563,0.208 10 CANL 6.51,3.292 7.073,3.5 0.563,0.208 10 BAT 5.583,2.281 6.146,2.49 0.563,0.208 10 G14 1.344,1.677 1.906,1.885 0.563,0.208 10 G118
*1 No. 1 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 1 CAN Junction Connector)
*b Front view of DLC3


Code Color (CANH Side) Color (CANL Side) Connect to
G118 L W No. 3 CAN Junction Connector


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G118-1 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G118-2 (CANL) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.CONNECT CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - NO. 3 CAN JUNCTION CONNECTOR)

11.CONNECT CONNECTOR
a.

Reconnect wire harness No. 1 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

12.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR SIDE)
12.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR SIDE)
a.
C253362C02
0.146,1.125 0.542,1.365 0.396,0.24 1.958,0.917 2.333,0.417 2.333,0.417 2.583,0.417 true 1.948,1.49 1.625,1.917 1.625,1.917 1.375,1.917 true 2.833,1.833 2.583,1.833 2.583,1.833 2.323,1.458 true 0.208,1.167 0.479,1.333 0.271,0.167 10 G14 0.094,0.115 0.365,0.281 0.271,0.167 10 *a 2.625,0.333 3.094,0.5 0.469,0.167 10 CANH 0.948,1.833 1.417,2 0.469,0.167 10 CANL 2.885,1.75 3.219,2 0.333,0.25 10 BAT
*a Front view of DLC3


Disconnect the G129 No. 2 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G14-6 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G14-14 (CANL) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR)

NG

28.CONNECT CONNECTOR
13.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 2 CAN junction connectors.

C278785C15
5.469,2.198 5.854,2.469 0.385,0.271 3.323,2.885 3.49,2.677 3.49,2.677 3.635,2.677 true 3.323,3.031 3.479,3.167 3.479,3.167 3.635,3.167 true 6.208,3.188 6.365,3.323 6.365,3.323 6.521,3.323 true 0.104,0.094 0.417,0.25 0.313,0.156 10 false *1 1.344,1.677 1.75,1.833 0.406,0.156 10 false G155 2.49,2.396 2.802,2.552 0.313,0.156 10 false *a 4.688,2.333 5,2.49 0.313,0.156 10 false *b 3.677,2.583 4.167,2.823 0.49,0.24 10 false CANH 3.677,3.083 4.167,3.323 0.49,0.24 10 false CANL 6.583,3.24 7.073,3.479 0.49,0.24 10 false BAT 5.521,2.25 6.01,2.49 0.49,0.24 10 false G14 1.344,1.896 1.75,2.052 0.406,0.156 10 false G156 1.344,2.125 1.75,2.281 0.406,0.156 10 false G128 1.344,2.563 1.75,2.719 0.406,0.156 10 false G130 1.344,2.781 1.75,2.938 0.406,0.156 10 false G131 1.344,3 1.75,3.156 0.406,0.156 10 false G132
*1 No. 2 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 2 CAN Junction Connector)
*b Front view of DLC3


Code Color (CANH Side) Color (CANL Side) Connect to

*1: for Radio and Display Type

*2: for Navigation Receiver Type

*3: for 4WD/AWD

*4: w/ Entry and Start System

G128 G W Combination Meter Assembly
G130 Y W
·

Radio and Display Receiver Assembly*1

·

Navigation ECU Sub-assembly*2


G131 L W 4WD ECU Assembly*3
G132 R W Certification ECU (Smart Key ECU Assembly)*4
G155 LG W Power Steering ECU Assembly
G156 P W Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor)


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G128-1 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G128-2 (CANL) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G130-1 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G130-2 (CANL) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G131-1 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G131-2 (CANL) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G132-1 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G132-2 (CANL) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G155-1 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G155-2 (CANL) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G156-1 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G156-2 (CANL) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Result Proceed to
OK A
NG (to combination meter assembly CAN main wire) B
NG (to radio and display receiver assembly [for Radio and Display Type] or navigation ECU sub-assembly [for Navigation Receiver Type] CAN branch wire) C
NG (to 4WD ECU assembly CAN branch wire) D
NG (to certification ECU [smart key ECU assembly] CAN branch wire) E
NG (to power steering ECU assembly CAN branch wire) F
NG (to spiral with sensor cable sub-assembly [steering angle sensor] CAN branch wire) G



A

REPLACE NO. 2 CAN JUNCTION CONNECTOR

B

14.CONNECT CONNECTOR

C

16.CONNECT CONNECTOR

D

20.CONNECT CONNECTOR

E

22.CONNECT CONNECTOR

F

24.CONNECT CONNECTOR

G

26.CONNECT CONNECTOR
14.CONNECT CONNECTOR
a.

Reconnect all wire harness No. 2 CAN junction connectors.


Result:
Proceed to
NEXT



NEXT

15.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (COMBINATION METER ASSEMBLY)
15.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (COMBINATION METER ASSEMBLY)
a.
C235425C01
0.354,0.948 0.771,1.198 0.417,0.25 0.344,2.531 0.76,2.781 0.417,0.25 2.531,3.167 2.365,3.167 2.365,3.167 2.198,2.917 true 2.167,1.667 2,1.667 2,1.667 1.688,1.167 true 1.083,1.667 1.333,1.667 1.333,1.667 1.604,1.167 true 0.083,0.083 0.333,0.333 0.25,0.25 10 *a 0.167,2.01 0.479,2.167 0.313,0.156 10 *b 0.417,2.583 0.833,2.833 0.417,0.25 10 G14 0.417,1 0.833,1.25 0.417,0.25 10 G16 0.667,1.583 1.083,1.833 0.417,0.25 10 CANH 2.219,1.583 2.635,1.833 0.417,0.25 10 CANL 2.583,3.094 3,3.344 0.417,0.25 10 BAT
*a Rear view of wire harness connector
(to Combination Meter Assembly)
*b Front view of DLC3


Disconnect the combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-32 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G16-31 (CANL) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (CANH, CANL)

16.CONNECT CONNECTOR
a.

Reconnect all wire harness No. 2 CAN junction connectors.


Result:
Proceed to
NEXT



NEXT

17.CHECK VEHICLE TYPE
17.CHECK VEHICLE TYPE
a.

Check for vehicle types.


Result:
Proceed to
for Radio and Display Type
for Navigation Receiver Type



for Radio and Display Type

18.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY)

for Navigation Receiver Type

19.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NAVIGATION ECU SUB-ASSEMBLY)
18.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.
C235427C04
0.365,2.615 0.792,2.885 0.427,0.271 1.406,0.229 1.802,0.479 0.396,0.25 2.167,2.927 2.323,3.198 2.323,3.198 2.51,3.198 true 1.969,1.177 2.24,1.656 2.24,1.656 2.49,1.656 true 1.833,1.177 1.604,1.646 1.604,1.646 1.396,1.646 true 0.094,0.073 0.406,0.229 0.313,0.156 10 *a 0.115,2.177 0.427,2.333 0.313,0.156 10 *b 0.438,2.667 0.854,2.906 0.417,0.24 10 G14 2.573,3.135 2.99,3.375 0.417,0.24 10 BAT 0.948,1.594 1.469,1.885 0.521,0.292 10 CANH 2.552,1.583 3.073,1.875 0.521,0.292 10 CANL 1.438,0.271 1.885,0.542 0.448,0.271 10 G143
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
*b Front view of DLC3


Disconnect the radio and display receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G143-9 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G143-10 (CANL) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO RADIO AND DISPLAY RECEIVER ASSEMBLY (CANH, CANL)

19.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NAVIGATION ECU SUB-ASSEMBLY)
a.
C235427C03
0.365,2.615 0.792,2.885 0.427,0.271 1.406,0.229 1.802,0.479 0.396,0.25 2.167,2.927 2.323,3.198 2.323,3.198 2.51,3.198 true 1.969,1.177 2.24,1.656 2.24,1.656 2.49,1.656 true 1.833,1.177 1.604,1.646 1.604,1.646 1.396,1.646 true 0.094,0.073 0.406,0.229 0.313,0.156 10 *a 0.115,2.177 0.427,2.333 0.313,0.156 10 *b 0.438,2.667 0.854,2.906 0.417,0.24 10 G14 2.573,3.135 2.99,3.375 0.417,0.24 10 BAT 0.948,1.594 1.469,1.885 0.521,0.292 10 CANH 2.552,1.583 3.073,1.875 0.521,0.292 10 CANL 1.438,0.271 1.885,0.542 0.448,0.271 10 G139
*a Front view of wire harness connector
(to Navigation ECU Sub-assembly)
*b Front view of DLC3


Disconnect the navigation ECU sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G139-9 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G139-10 (CANL) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO NAVIGATION ECU SUB-ASSEMBLY (CANH, CANL)

20.CONNECT CONNECTOR
a.

Reconnect all wire harness No. 2 CAN junction connectors.


Result:
Proceed to
NEXT



NEXT

21.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (4WD ECU ASSEMBLY)
21.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (4WD ECU ASSEMBLY)
a.
C251150C08
0.417,2.51 0.823,2.792 0.406,0.281 0.438,0.927 0.844,1.208 0.406,0.281 2.219,1.104 2.448,1.385 2.448,1.385 2.625,1.385 true 2.167,1.104 2.323,1.604 2.323,1.604 2.51,1.604 true 2.208,2.833 2.406,3.021 2.406,3.021 2.594,3.021 true 0.083,0.094 0.396,0.25 0.313,0.156 10 false *a 0.104,2.083 0.417,2.24 0.313,0.156 10 false *b 0.51,2.563 0.885,2.771 0.375,0.208 10 false G14 2.667,2.896 3.042,3.104 0.375,0.208 10 false BAT 2.667,1.281 3.146,1.552 0.479,0.271 10 false CANL 2.563,1.5 3.042,1.771 0.479,0.271 10 false CANH 0.521,0.979 0.896,1.188 0.375,0.208 10 false G86
*a Rear view of wire harness connector
(to 4WD ECU Assembly)
*b Front view of DLC3


Disconnect the 4WD ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G86-6 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G86-5 (CANL) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO 4WD ECU ASSEMBLY (CANH, CANL)

22.CONNECT CONNECTOR
a.

Reconnect all wire harness No. 2 CAN junction connectors.


Result:
Proceed to
NEXT



NEXT

23.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CERTIFICATION ECU)
23.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CERTIFICATION ECU)
a.
C278757C01
0.333,2.531 0.75,2.823 0.417,0.292 0.271,0.948 0.688,1.24 0.417,0.292 2.188,2.833 2.302,3.104 2.302,3.104 2.51,3.104 true 2.031,1.052 2.344,0.344 2.344,0.344 2.552,0.344 true 1.917,1.031 1.604,0.323 1.604,0.323 1.406,0.323 true 0.167,0.125 0.385,2 0.219,1.875 10 *a 0.167,2.083 0.479,2.24 0.313,0.156 10 *b 0.417,2.583 0.813,2.823 0.396,0.24 10 G14 0.333,1.01 0.729,1.25 0.396,0.24 10 G84 2.573,3.042 2.969,3.281 0.396,0.24 10 BAT 2.594,0.271 3.198,0.542 0.604,0.271 10 CANL 0.979,0.271 1.583,0.542 0.604,0.271 10 CANH
*a Front view of wire harness connector
(to Certification ECU [Smart Key ECU Assembly])
*b Front view of DLC3


Disconnect the certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G84-14 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G84-15 (CANL) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CERTIFICATION ECU (CANH, CANL)

24.CONNECT CONNECTOR
a.

Reconnect all wire harness No. 2 CAN junction connectors.


Result:
Proceed to
NEXT



NEXT

25.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (POWER STEERING ECU ASSEMBLY)
25.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (POWER STEERING ECU ASSEMBLY)
a.
C278758C01
0.448,2.542 0.844,2.792 0.396,0.25 2.323,1.052 2.719,1.302 0.396,0.25 1.073,0.927 1.229,0.927 1.229,0.927 1.469,1.125 true 1.146,1.646 1.302,1.646 1.302,1.646 1.49,1.302 true 2.521,3.073 2.354,3.073 2.354,3.073 2.198,2.813 true 0.115,0.083 0.427,0.24 0.313,0.156 10 *a 0.188,2.01 0.5,2.167 0.313,0.156 10 *b 2.438,1.094 2.75,1.25 0.313,0.156 10 h1 0.5,2.583 0.833,2.833 0.333,0.25 10 G14 2.583,3 2.917,3.25 0.333,0.25 10 BAT 0.667,0.833 1.167,1.083 0.5,0.25 10 CANH 0.75,1.583 1.25,1.833 0.5,0.25 10 CANL
*a Rear view of wire harness connector
(to Power Steering ECU Assembly)
*b Front view of DLC3


Disconnect the power steering ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
h1-4 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
h1-8 (CANL) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER STEERING ECU ASSEMBLY (CANH, CANL)

26.CONNECT CONNECTOR
a.

Reconnect all wire harness No. 2 CAN junction connectors.


Result:
Proceed to
NEXT



NEXT

27.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (STEERING ANGLE SENSOR)
27.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (STEERING ANGLE SENSOR)
a.
C278759C01
0.438,2.542 0.854,2.792 0.417,0.25 0.5,0.979 0.917,1.229 0.417,0.25 1.167,1.75 1.333,1.75 1.333,1.75 1.583,1.333 true 2.198,2.802 2.417,3.083 2.417,3.083 2.583,3.083 true 1.729,1.333 2,1.75 2,1.75 2.167,1.75 true 0.083,0.094 0.396,0.25 0.313,0.156 10 *a 0.104,2 0.417,2.156 0.313,0.156 10 *b 0.583,1.021 0.917,1.26 0.333,0.24 10 G12 0.5,2.583 0.833,2.823 0.333,0.24 10 G14 0.75,1.667 1.25,1.906 0.5,0.24 10 CANL 2.219,1.677 2.719,1.917 0.5,0.24 10 CANH 2.667,3.01 3.167,3.25 0.5,0.24 10 BAT
*a Front view of wire harness connector
(to Spiral with Sensor Cable Sub-assembly [Steering Angle Sensor])
*b Front view of DLC3


Disconnect the spiral with sensor cable sub-assembly (steering angle sensor) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G12-3 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G12-2 (CANL) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO STEERING ANGLE SENSOR (CANH, CANL)

28.CONNECT CONNECTOR
a.

Reconnect wire harness No. 2 CAN junction connector.

Result:
Proceed to
NEXT




NEXT

29.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR)
29.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 1 CAN junction connectors.

C253917C40
5.521,2.229 5.927,2.479 0.406,0.25 3.302,2.875 3.469,2.698 3.469,2.698 3.552,2.698 true 3.302,3.01 3.458,3.177 3.458,3.177 3.542,3.177 true 6.219,3.198 6.375,3.365 6.375,3.365 6.458,3.365 true 0.063,0.042 0.375,0.198 0.313,0.156 10 false *1 3.594,2.604 4.156,2.813 0.563,0.208 10 false CANH 2.521,2.417 2.833,2.573 0.313,0.156 10 false *a 4.604,2.344 4.917,2.5 0.313,0.156 10 false *b 3.594,3.083 4.156,3.292 0.563,0.208 10 false CANL 6.51,3.292 7.073,3.5 0.563,0.208 10 false BAT 5.583,2.281 6.146,2.49 0.563,0.208 10 false G14 1.344,2.115 1.906,2.323 0.563,0.208 10 false G120 1.344,2.344 1.906,2.552 0.563,0.208 10 false G126 1.333,2.563 1.896,2.771 0.563,0.208 10 false G127 1.344,2.792 1.906,3 0.563,0.208 10 false G123 1.333,3.219 1.896,3.427 0.563,0.208 10 false G125 1.354,1.896 1.917,2.104 0.563,0.208 10 false G119
*1 No. 1 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 1 CAN Junction Connector)
*b Front view of DLC3


Code Color (CANH Side) Color (CANL Side) Connect to

*: w/ Stop and Start System

G119 V W No. 2 CAN Junction Connector
G120 R W Brake Actuator Assembly (Skid Control ECU)
G123 Y W Main Body ECU (Multiplex Network Body ECU)
G125 BR W Airbag Sensor Assembly
G126 G W Air Conditioning Amplifier Assembly
G127 LG W Engine Stop and Start ECU*


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G119-1 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G119-2 (CANL) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G120-1 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G120-2 (CANL) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G123-1 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G123-2 (CANL) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G125-1 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G125-2 (CANL) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G126-1 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G126-2 (CANL) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G127-1 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G127-2 (CANL) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Result Proceed to
OK A
NG (to brake actuator assembly [skid control ECU] CAN branch wire) B
NG (to main body ECU [multiplex network body ECU] CAN branch wire) C
NG (to airbag sensor assembly CAN branch wire) D
NG (to air conditioning amplifier assembly CAN branch wire) E
NG (to engine stop and start ECU CAN branch wire) F
NG (to No. 2 CAN junction connector CAN main wire) G



A

REPLACE NO. 1 CAN JUNCTION CONNECTOR

B

30.CONNECT CONNECTOR

C

32.CONNECT CONNECTOR

D

34.CONNECT CONNECTOR

E

36.CONNECT CONNECTOR

F

38.CONNECT CONNECTOR

G

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

30.CONNECT CONNECTOR
a.

Reconnect all wire harness No. 1 CAN junction connectors.


Result:
Proceed to
NEXT



NEXT

31.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (SKID CONTROL ECU)
31.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (SKID CONTROL ECU)
a.
C235295C03
1.49,0.094 1.906,0.365 0.417,0.271 0.385,2.583 0.802,2.854 0.417,0.271 2.198,2.885 2.365,3.135 2.365,3.135 2.635,3.135 true 1.365,1.115 0.74,0.729 0.74,0.729 0.542,0.729 true 1.385,1.198 0.979,1.76 0.979,1.76 0.708,1.76 true 1.573,0.156 1.948,0.365 0.375,0.208 10 A64 0.073,0.083 0.385,0.24 0.313,0.156 10 *a 0.104,2.146 0.417,2.302 0.313,0.156 10 *b 0.448,2.646 0.823,2.854 0.375,0.208 10 G14 2.688,3.052 3.125,3.26 0.438,0.208 10 BAT 0.302,1.688 0.813,1.896 0.51,0.208 10 CANH 0.167,0.667 0.677,0.875 0.51,0.208 10 CANL
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])
*b Front view of DLC3


Disconnect the brake actuator assembly (skid control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A64-25 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A64-14 (CANL) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SKID CONTROL ECU (CANH, CANL)

32.CONNECT CONNECTOR
a.

Reconnect all wire harness No. 1 CAN junction connectors.


Result:
Proceed to
NEXT



NEXT

33.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (MAIN BODY ECU)
33.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (MAIN BODY ECU)
a.
C206323C05
0.354,2.625 0.771,2.875 0.417,0.25 0.417,1 0.833,1.25 0.417,0.25 2.292,2.927 2.427,3.167 2.427,3.167 2.677,3.167 true 0.917,0.333 1.25,0.333 1.25,0.333 1.635,1.083 true 0.75,0.583 1,0.583 1,0.583 1.563,1.104 true 0.083,0.083 0.417,0.25 0.333,0.167 10 false *a 0.167,2.083 0.479,2.24 0.313,0.156 10 false *b 0.438,2.667 0.833,2.917 0.396,0.25 10 false G14 0.49,1.052 0.885,1.302 0.396,0.25 10 false G78 0.333,0.51 0.833,0.76 0.5,0.25 10 false CANH 0.5,0.24 1,0.49 0.5,0.25 10 false CANL 2.75,3.083 3.25,3.333 0.5,0.25 10 false BAT
*a Rear view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU])
*b Front view of DLC3


Disconnect the main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G78-14 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G78-13 (CANL) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MAIN BODY ECU (CANH, CANL)

34.CONNECT CONNECTOR
a.

Reconnect all wire harness No. 1 CAN junction connectors.


Result:
Proceed to
NEXT



NEXT

35.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (AIRBAG SENSOR ASSEMBLY)
35.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (AIRBAG SENSOR ASSEMBLY)
a.
C227529C01
0.375,2.521 0.771,2.781 0.396,0.26 0.365,0.948 0.76,1.208 0.396,0.26 2.198,2.896 2.333,3.115 2.333,3.115 2.552,3.115 true 2.115,1.323 2.313,1.677 2.313,1.677 2.552,1.677 true 2.021,1.01 2.438,0.656 2.438,0.656 2.688,0.656 true 0.177,0.073 0.427,0.271 0.25,0.198 10 *a 0.198,2.083 0.51,2.24 0.313,0.156 10 *b 0.438,2.573 0.781,2.781 0.344,0.208 10 G14 0.417,1 0.76,1.208 0.344,0.208 10 G92 2.75,0.583 3.292,0.792 0.542,0.208 10 CANH 2.604,1.604 3.146,1.813 0.542,0.208 10 CANL 2.604,3.042 3.146,3.25 0.542,0.208 10 BAT
*a Rear view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of DLC3


Disconnect the airbag sensor assembly connector.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/o Occupant Classification System)>PRECAUTION


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G92-13 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G92-22 (CANL) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIRBAG SENSOR ASSEMBLY (CANH, CANL)

36.CONNECT CONNECTOR
a.

Reconnect all wire harness No. 1 CAN junction connectors.


Result:
Proceed to
NEXT



NEXT

37.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY)
37.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the air conditioning amplifier assembly connector.

C278756C01
5.729,0.698 6.146,0.948 0.417,0.25 3.438,0.521 3.854,0.771 0.417,0.25 1.167,0.552 1.583,0.802 0.417,0.25 6.396,1.729 6.573,1.948 6.573,1.948 6.771,1.948 true 1.333,1.49 1.823,2.104 1.823,2.104 2.021,2.104 true 1.24,1.479 1.49,2.365 1.49,2.365 1.688,2.365 true 2.573,0.979 2.823,0.979 2.823,0.979 3.042,1.406 true 2.74,0.729 2.99,0.729 2.99,0.729 3.125,1.417 true 1.24,0.594 1.698,0.792 0.458,0.198 10 G81 0.125,0.083 0.583,0.281 0.458,0.198 10 *a 5,0.135 5.458,0.333 0.458,0.198 10 *b 3.5,0.552 3.958,0.75 0.458,0.198 10 G80 5.792,0.75 6.25,0.948 0.458,0.198 10 G14 2.156,0.906 2.615,1.104 0.458,0.198 10 CANL 2.083,2.031 2.542,2.229 0.458,0.198 10 CANH 1.75,2.292 2.208,2.49 0.458,0.198 10 CANL 2.323,0.656 2.781,0.854 0.458,0.198 10 CANH 6.813,1.885 7.146,2.229 0.333,0.344 10 BAT 3.938,0.563 4.396,0.76 0.458,0.198 10 *B 1.646,0.583 2.104,0.781 0.458,0.198 10 *A
*A for Automatic Air Conditioning System *B for Manual Air Conditioning System
*a Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly)
*b Front view of DLC3



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for Automatic Air Conditioning System
Tester Connection Condition Specified Condition
G81-11 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G81-12 (CANL) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

for Manual Air Conditioning System
Tester Connection Condition Specified Condition
G80-8 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G80-9 (CANL) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIR CONDITIONING AMPLIFIER ASSEMBLY (CANH, CANL)

38.CONNECT CONNECTOR
a.

Reconnect all wire harness No. 1 CAN junction connectors.


Result:
Proceed to
NEXT



NEXT

39.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ENGINE STOP AND START ECU)
39.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ENGINE STOP AND START ECU)
a.
C251432C03
0.281,2.49 0.677,2.719 0.396,0.229 0.375,0.854 0.771,1.083 0.396,0.229 2.229,2.865 2.51,3.135 2.51,3.135 2.802,3.135 true 2.177,1.115 2.5,1.344 2.5,1.344 2.74,1.344 true 2.083,1.115 2.323,1.604 2.323,1.604 2.563,1.604 true 0.073,0.042 0.385,0.198 0.313,0.156 10 *a 0.125,1.917 0.438,2.073 0.313,0.156 10 *b 0.344,2.531 0.625,2.719 0.281,0.188 10 G14 0.438,0.906 0.719,1.094 0.281,0.188 10 G87 2.583,1.531 3.094,1.698 0.51,0.167 10 CANL 2.771,1.26 3.281,1.427 0.51,0.167 10 CANH 2.833,3.063 3.344,3.229 0.51,0.167 10 BAT
*a Rear view of wire harness connector
(to Engine Stop and Start ECU)
*b Front view of DLC3


Disconnect the engine stop and start ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G87-15 (CANH) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G87-16 (CANL) - G14-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO ENGINE STOP AND START ECU (CANH, CANL)