Home › Engine / Hybrid System › 2AR-FE ENGINE CONTROL › SFI SYSTEM(w/ Canister Pump Module) › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _008378 2AR-FE ENGINE CONTROL _0060196 SFI SYSTEM(w/ Canister Pump Module) C

2AR-FE ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P0300  Random / Multiple Cylinder Misfire Detected  P0301  Cylinder 1 Misfire Detected  P0302  Cylinder 2 Misfire Detected  P0303  Cylinder 3 Misfire Detected  P0304  Cylinder 4 Misfire Detected  


DESCRIPTION

When the engine misfires, high concentrations of hydrocarbons (HC) enter the exhaust gas. Extremely high hydrocarbon concentration levels can cause an increase in exhaust emission levels. Extremely high concentrations of hydrocarbons can also cause increases in the three-way catalytic converter temperature, which may cause damage to the three-way catalytic converter. To prevent this increase in emissions and to limit the possibility of thermal damage, the ECM monitors the misfire count. When the temperature of the three-way catalytic converter reaches the point of thermal degradation, the ECM blinks the MIL. To monitor misfires, the ECM uses both the camshaft position sensor and the crankshaft position sensor. The camshaft position sensor is used to identify any misfiring cylinders and the crankshaft position sensor is used to measure variations in the crankshaft rotation speed. Misfires are counted when the crankshaft rotation speed variations exceed predetermined thresholds. If the misfire count exceeds the threshold levels, and could cause emission control system performance deterioration, the ECM illuminates the MIL and stores a DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0300 Random / Multiple Cylinder Misfire Detected Simultaneous misfiring of several cylinders occurs and one of the following conditions is met (2 trip detection logic).
·

A misfire occurs that may damage the three-way catalytic converter (MIL blinks when detect immediately).

·

An emission deterioration misfire occurs (MIL illuminates).


·

Open or short in engine wire harness

·

Connector connection

·

Vacuum hose connections

·

Ignition system

·

Fuel injector assembly

·

Fuel pressure

·

Mass air flow meter sub-assembly

·

Engine coolant temperature sensor

·

Compression pressure

·

Valve timing

·

PCV valve and hose

·

PCV hose connections

·

Intake system

·

Intake air control valve actuator (for tumble control valve)

·

ECM


Comes on/Blinks*
*: The MIL flashes when a catalyst-damaging misfire is detected.
DTC stored
P0301 Cylinder 1 Misfire Detected Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic).
·

A misfire occurs that may damage the three-way catalytic converter (MIL blinks when detect immediately).

·

An emission deterioration misfire occurs (MIL illuminates).


·

Open or short in engine wire harness

·

Connector connection

·

Vacuum hose connections

·

Ignition system

·

Fuel injector assembly

·

Fuel pressure

·

Mass air flow meter sub-assembly

·

Engine coolant temperature sensor

·

Compression pressure

·

Valve timing

·

PCV valve and hose

·

PCV hose connections

·

Intake system

·

Intake air control valve actuator (for tumble control valve)

·

ECM


Comes on/Blinks*
*: The MIL flashes when a catalyst-damaging misfire is detected.
DTC stored
P0302 Cylinder 2 Misfire Detected Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic).
·

A misfire occurs that may damage the three-way catalytic converter (MIL blinks when detect immediately).

·

An emission deterioration misfire occurs (MIL illuminates).


·

Open or short in engine wire harness

·

Connector connection

·

Vacuum hose connections

·

Ignition system

·

Fuel injector assembly

·

Fuel pressure

·

Mass air flow meter sub-assembly

·

Engine coolant temperature sensor

·

Compression pressure

·

Valve timing

·

PCV valve and hose

·

PCV hose connections

·

Intake system

·

Intake air control valve actuator (for tumble control valve)

·

ECM


Comes on/Blinks*
*: The MIL flashes when a catalyst-damaging misfire is detected.
DTC stored
P0303 Cylinder 3 Misfire Detected Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic).
·

A misfire occurs that may damage the three-way catalytic converter (MIL blinks when detect immediately).

·

An emission deterioration misfire occurs (MIL illuminates).


·

Open or short in engine wire harness

·

Connector connection

·

Vacuum hose connections

·

Ignition system

·

Fuel injector assembly

·

Fuel pressure

·

Mass air flow meter sub-assembly

·

Engine coolant temperature sensor

·

Compression pressure

·

Valve timing

·

PCV valve and hose

·

PCV hose connections

·

Intake system

·

Intake air control valve actuator (for tumble control valve)

·

ECM


Comes on/Blinks*
*: The MIL flashes when a catalyst-damaging misfire is detected.
DTC stored
P0304 Cylinder 4 Misfire Detected Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic).
·

A misfire occurs that may damage the three-way catalytic converter (MIL blinks when detect immediately).

·

An emission deterioration misfire occurs (MIL illuminates).


·

Open or short in engine wire harness

·

Connector connection

·

Vacuum hose connections

·

Ignition system

·

Fuel injector assembly

·

Fuel pressure

·

Mass air flow meter sub-assembly

·

Engine coolant temperature sensor

·

Compression pressure

·

Valve timing

·

PCV valve and hose

·

PCV hose connections

·

Intake system

·

Intake air control valve actuator (for tumble control valve)

·

ECM


Comes on/Blinks*
*: The MIL flashes when a catalyst-damaging misfire is detected.
DTC stored

When DTCs for misfiring cylinders are randomly stored, but DTC P0300 is not stored, it indicates that misfires have been detected in different cylinders at different times. DTC P0300 is only stored when several misfiring cylinders are detected at the same time.

MONITOR DESCRIPTION

The ECM illuminates the MIL and stores a DTC when either one of the following conditions, which could cause emission deterioration, is detected (2 trip detection logic).

·

Within the first 1000 crankshaft revolutions after the engine starts, an excessive number of misfires (approximately 10 to 70 misfires per 1000 crankshaft revolutions) occurs once.

·

An excessive number of misfires (approximately 10 to 70 misfires per 1000 crankshaft revolutions) occurs a total of 4 times.


The ECM flashes the MIL (immediate detection logic) and stores a DTC (2 trip detection logic) when either one of the following conditions, which could cause damage to the three-way catalytic converter, is detected.

·

At a high engine speed, a sufficient number of misfires to damage the catalyst occurring within 200 crankshaft revolutions is detected once.

·

At a normal engine speed, a sufficient number of misfires to damage the catalyst occurring within 200 crankshaft revolutions is detected 3 times.


MONITOR STRATEGY

Required Sensors/Components (Main) Crankshaft position sensor
Camshaft position sensor
Required Sensors/Components (Related) Engine coolant temperature
Intake air temperature sensor
Mass air flow meter sub-assembly
Frequency of Operation Continuous

TYPICAL ENABLING CONDITIONS

Misfire
Either of the following conditions is met A or B
A. Engine coolant temperature at engine start Higher than -7°C (19°F)
B. Engine coolant temperature Higher than 20°C (68°F)

Monitor Period of Emission-related Misfire
First 1000 revolutions after engine start, or during check mode Crankshaft 1000 revolutions
Except above Crankshaft 1000 revolutions x 4

Monitor Period of Catalyst-damaging Misfire (MIL Blinks)
All of the following conditions 1, 2, 3 and 4 met Crankshaft 200 revolutions x 3
Except above (MIL blinks immediately) Crankshaft 200 revolutions
1. Driving cycles 1st
2. Check mode Off
3. Engine speed Less than 2450 rpm
4. Intake air amount per revolution Less than 0.95 g/rev

TYPICAL MALFUNCTION THRESHOLDS

Monitor Period of Emission-related Misfire
Misfire rate 1.493% or higher

Monitor Period of Catalyst-damaging Misfire (MIL Blinks)
Number of misfires per 200 revolutions 130 or more (varies with intake air amount and engine speed)

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Record the DTC(s) and freeze frame data.

5.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

6.

Using the GTS, switch the ECM from normal mode to check mode.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>CHECK MODE PROCEDURE

7.

Read the misfire counts of each cylinder, Cylinder #1 Misfire Count to Cylinder #4 Misfire Count, with the engine idling. If any misfire count is displayed, skip the following confirmation driving pattern.

8.

Drive the vehicle so that the vehicle conditions displayed in Misfire RPM and Misfire Load of the Data List are the same as the freeze frame data. Perform this step several times.

HINT:

In order to store misfire DTCs, it is necessary to operate the vehicle for the period of time shown in the table below, confirm the Misfire RPM and Misfire Load in the Data List.

Engine speed Duration
Idling 8.0 minutes or more
1000 4.5 minutes or more
2000 2.5 minutes or more
3000 1.5 minutes or more


9.

Check whether misfires have occurred by checking DTCs and freeze frame data.

HINT:

Do not turn the ignition switch off until the output DTC(s) and freeze frame data have been recorded. When the ECM returns to normal mode (default), the stored DTC(s), freeze frame data and other data are cleared.


10.

Record the DTC(s), freeze frame data and misfire counts.

11.

Turn the ignition switch off and wait for at least 30 seconds.

12.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).


CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

If any DTCs other than misfire DTCs are output, troubleshoot those DTCs first.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

If the misfire does not recur when the vehicle is brought to the workshop, reproduce the conditions stored in the ECM as freeze frame data.

·

If the misfire still cannot be reproduced even though the conditions stored in the ECM as freeze frame data have been reproduced, one of the following factors is considered to be a possible cause of the problem:

1.

There was insufficient fuel in the tank.

2.

Improper fuel was used.

3.

The spark plugs have been contaminated.

4.

The problem requires further diagnosis.


·

After finishing repairs, check the misfire counts of the cylinders (Cylinder #1 Misfire Count to Cylinder #4 Misfire Count).

·

Be sure to confirm that no misfiring cylinder DTCs are stored again by conducting the confirmation driving pattern after finishing repairs.

·

When one of Short FT #1 or Long FT #1 in the freeze frame data is outside the range of +/-15%, the air fuel ratio may be rich (-15% or less) or lean (+15% or higher).

·

When Coolant Temp in the freeze frame data is below 75°C (167°F), the misfires have occurred only while warming up the engine.

·

An extremely imbalanced drive wheel which causes body vibration may cause misfire DTCs to be stored.



PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO MISFIRE DTCS)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
DTC P0300, P0301, P0302, P0303 and/or P0304 are output A
DTC P0300, P0301, P0302, P0303 and/or P0304 and other DTCs are output B


HINT:

If any DTCs other than P0300, P0301, P0302, P0303 and P0304 are output, troubleshoot those DTCs first.




A

2.CHECK PCV HOSE CONNECTIONS

B

2.CHECK PCV HOSE CONNECTIONS
a.

Check the PCV hose connections

Click hereEngine / Hybrid System>2AR-FE EMISSION CONTROL>EMISSION CONTROL SYSTEM(w/ Canister Pump Module)>ON-VEHICLE INSPECTION

OK:

PCV valve and hose are correctly connected and are not damaged.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (MISFIRE RPM AND MISFIRE LOAD)

NG

REPAIR OR REPLACE PCV HOSE

3.READ VALUE USING GTS (MISFIRE RPM AND MISFIRE LOAD)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Ptrl Misfire / Misfire RPM and Misfire Load.

Powertrain > Engine and ECT > Data List
Tester Display
Misfire RPM
Misfire Load
50003 234 319,320

e.

Read and note the Misfire RPM and Misfire Load values.

HINT:

The Misfire RPM and Misfire Load values indicate the vehicle conditions under which the misfire occurred.



Result:
Proceed to
NEXT



NEXT

4.READ VALUE USING GTS (CATALYST OT MF F/C)
4.READ VALUE USING GTS (CATALYST OT MF F/C)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Ptrl Misfire / Catalyst OT MF F/C.

Powertrain > Engine and ECT > Data List
Tester Display
Catalyst OT MF F/C
50003 234 341

e.

Read the value displayed on the GTS.

Result:
Data List GTS Display Proceed to
Catalyst OT MF F/C Avail A
Not Avl B




A

5.PERFORM ACTIVE TEST USING GTS (PROHIBIT THE CATALYST OT MISFIRE PREVENT F/C)

B

6.READ VALUE USING GTS (CYLINDER MISFIRE COUNT)
5.PERFORM ACTIVE TEST USING GTS (PROHIBIT THE CATALYST OT MISFIRE PREVENT F/C)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Prohibit the Catalyst OT Misfire Prevent F/C.

Powertrain > Engine and ECT > Active Test
Tester Display
Prohibit the Catalyst OT Misfire prevent F/C
50004 234 155

e.

Perform the Active Test.

NOTICE:

When performing the Active Test, make sure the vehicle is stopped and the engine is either idling or being revved within 3000 rpm.



Result:
Proceed to
NEXT



NEXT

6.READ VALUE USING GTS (CYLINDER MISFIRE COUNT)
6.READ VALUE USING GTS (CYLINDER MISFIRE COUNT)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Ptrl Misfire / Cylinder #1 Misfire Count, Cylinder #2 Misfire Count, Cylinder #3 Misfire Count and Cylinder #4 Misfire Count.

Powertrain > Engine and ECT > Data List
Tester Display
Cylinder #1 Misfire Count
Cylinder #2 Misfire Count
Cylinder #3 Misfire Count
Cylinder #4 Misfire Count
50003 234 321,322,323,324

e.

Start the engine and allow the engine to idle.


f.

Read each value for Cylinder #1 Misfire Count to Cylinder #4 Misfire Count displayed on the GTS. If no misfire counts occur in any cylinders, perform procedure [A] and [B] and then check the misfire counts again.


g.

Drive the vehicle with the Misfire RPM and Misfire Load noted in the "Read Value Using GTS (Misfire RPM and Misfire Load)" procedures above [A].


h.

Read the Cylinder #1 Misfire Count to Cylinder #4 Misfire Count or DTCs displayed on the GTS [B].

Result:
Result Proceed to
Most misfires occur in only 1 or 2 cylinders A
3 cylinders or more have equal misfire counts B


HINT:
·

If it is difficult to reproduce misfires for each cylinder, check the Data List item called Misfire Margin. Try to find vehicle driving conditions that lower the Misfire Margin value. Values above 30% are considered normal.

·

If the freeze frame data record of the engine coolant temperature is below 75°C (167°F), the misfire may be detected only when the engine is cold.

·

If the freeze frame data record of the Engine Run Time is below 120 seconds, the misfire may be detected immediately after the engine is started.





A

7.INSPECT SPARK PLUG

B

18.CHECK INTAKE SYSTEM
7.INSPECT SPARK PLUG
a.

Inspect the spark plug of the misfiring cylinder.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>IGNITION SYSTEM>ON-VEHICLE INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the spark plug.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION



Result:
Proceed to
OK
NG



OK

8.CHECK FOR SPARK (SPARK TEST)

NG

8.CHECK FOR SPARK (SPARK TEST)
a.

Perform a spark test.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>IGNITION SYSTEM>ON-VEHICLE INSPECTION

HINT:
·

If the result of the spark test is normal, proceed to the next step.

·

Perform "Inspection After Repair" after repairing or replacing the ignition system.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION




Result:
Proceed to
NEXT



NEXT

9.CHECK CYLINDER COMPRESSION PRESSURE
9.CHECK CYLINDER COMPRESSION PRESSURE
a.

Measure the cylinder compression pressure of the misfiring cylinder.

Click hereEngine / Hybrid System>2AR-FE ENGINE MECHANICAL>ENGINE>ON-VEHICLE INSPECTION

HINT:

Perform "Inspection After Repair" after repairing or replacing the engine assembly.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION



Result:
Proceed to
OK
NG



OK

10.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR ASSEMBLY)

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

10.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR ASSEMBLY)
a.
A255689C34
0.917,0.083 1.333,0.333 0.417,0.25 1.854,1.271 1.583,1.865 false 1.781,1.271 1.281,1.823 false 1.927,1.281 1.958,1.865 false 2,1.354 2.25,1.896 false 2,1.271 2.604,1.865 false 0.99,0.125 1.333,0.292 0.344,0.167 10 B77 1.052,1.844 1.323,2.01 0.271,0.167 10 #20 1.771,1.896 2.042,2.063 0.271,0.167 10 #40 2.146,1.917 2.417,2.083 0.271,0.167 10 E01 1.396,1.885 1.667,2.052 0.271,0.167 10 #30 2.5,1.865 2.771,2.031 0.271,0.167 10 #10 0.083,0.094 0.271,0.26 0.188,0.167 10 *a
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B77-20 (#10) - B77-50 (E01) Ignition switch ON 11 to 14 V
B77-17 (#20) - B77-50 (E01) Ignition switch ON 11 to 14 V
B77-18 (#30) - B77-50 (E01) Ignition switch ON 11 to 14 V
B77-19 (#40) - B77-50 (E01) Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG




OK

11.CHECK FUEL INJECTOR OF MISFIRING CYLINDER

NG

11.CHECK FUEL INJECTOR OF MISFIRING CYLINDER
a.

Check the fuel injector assembly injection (whether fuel volume is high or low, and whether injection pattern is poor).

Click hereEngine / Hybrid System>2AR-FE FUEL>FUEL INJECTOR>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the fuel injector assembly.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION



Result:
Proceed to
OK
NG



OK

12.CHECK INTAKE SYSTEM

NG

REPLACE FUEL INJECTOR ASSEMBLY

12.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks.

Click hereEngine / Hybrid System>2AR-FE INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION

OK:

No leaks from intake system.


HINT:

Perform "Inspection After Repair" after repairing or replacing the intake system.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION



Result:
Proceed to
OK
NG



OK

13.CHECK INTAKE AIR CONTROL VALVE ACTUATOR (FOR TUMBLE CONTROL VALVE)

NG

REPAIR OR REPLACE INTAKE SYSTEM

13.CHECK INTAKE AIR CONTROL VALVE ACTUATOR (FOR TUMBLE CONTROL VALVE)
a.

Check the intake air control valve actuator (for tumble control valve).

Click hereEngine / Hybrid System>2AR-FE INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

14.CHECK FUEL PRESSURE

NG

REPLACE INTAKE AIR CONTROL VALVE ACTUATOR (FOR TUMBLE CONTROL VALVE)

14.CHECK FUEL PRESSURE

Result:
Proceed to
OK
NG



OK

15.READ VALUE USING GTS (COOLANT TEMP)

NG

34.CHECK FUEL LINE
15.READ VALUE USING GTS (COOLANT TEMP)

OK

16.READ VALUE USING GTS (MAF)

NG

16.READ VALUE USING GTS (MAF)

OK

17.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)

NG

29.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY CONNECTOR CONNECTION)
17.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)

OK

29.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY CONNECTOR CONNECTION)

NG

18.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks.

Click hereEngine / Hybrid System>2AR-FE INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION

OK:

No leaks from intake system.


HINT:

Perform "Inspection After Repair" after repairing or replacing the intake system.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION



Result:
Proceed to
OK
NG



OK

19.CHECK INTAKE AIR CONTROL VALVE ACTUATOR (FOR TUMBLE CONTROL VALVE)

NG

REPAIR OR REPLACE INTAKE SYSTEM

19.CHECK INTAKE AIR CONTROL VALVE ACTUATOR (FOR TUMBLE CONTROL VALVE)
a.

Check the intake air control valve actuator (for tumble control valve).

Click hereEngine / Hybrid System>2AR-FE INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

20.CHECK FUEL PRESSURE

NG

REPLACE INTAKE AIR CONTROL VALVE ACTUATOR (FOR TUMBLE CONTROL VALVE)

20.CHECK FUEL PRESSURE

Result:
Proceed to
OK
NG



OK

21.READ VALUE USING GTS (COOLANT TEMP)

NG

34.CHECK FUEL LINE
21.READ VALUE USING GTS (COOLANT TEMP)

OK

22.READ VALUE USING GTS (MAF)

NG

22.READ VALUE USING GTS (MAF)

OK

23.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)

NG

29.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY CONNECTOR CONNECTION)
23.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)

OK

24.INSPECT SPARK PLUG

NG

24.INSPECT SPARK PLUG
a.

Inspect the spark plug of the misfiring cylinder.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>IGNITION SYSTEM>ON-VEHICLE INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the spark plug

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION



Result:
Proceed to
OK
NG



OK

25.CHECK FOR SPARK (SPARK TEST)

NG

25.CHECK FOR SPARK (SPARK TEST)
a.

Perform a spark test.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>IGNITION SYSTEM>ON-VEHICLE INSPECTION

HINT:
·

If the result of the spark test is normal, proceed to the next step.

·

Perform "Inspection After Repair" after repairing or replacing the ignition system.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION




Result:
Proceed to
NEXT



NEXT

26.CHECK CYLINDER COMPRESSION PRESSURE
26.CHECK CYLINDER COMPRESSION PRESSURE
a.

Measure the cylinder compression pressure of the misfiring cylinder.

Click hereEngine / Hybrid System>2AR-FE ENGINE MECHANICAL>ENGINE>ON-VEHICLE INSPECTION

HINT:

Perform "Inspection After Repair" after repairing or replacing the engine assembly.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION



Result:
Proceed to
OK
NG



OK

27.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR ASSEMBLY)

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

27.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR ASSEMBLY)
a.
A255689C34
0.917,0.083 1.333,0.333 0.417,0.25 1.854,1.271 1.583,1.865 false 1.781,1.271 1.281,1.823 false 1.927,1.281 1.958,1.865 false 2,1.354 2.25,1.896 false 2,1.271 2.604,1.865 false 0.99,0.125 1.333,0.292 0.344,0.167 10 B77 1.052,1.844 1.323,2.01 0.271,0.167 10 #20 1.771,1.896 2.042,2.063 0.271,0.167 10 #40 2.146,1.917 2.417,2.083 0.271,0.167 10 E01 1.396,1.885 1.667,2.052 0.271,0.167 10 #30 2.5,1.865 2.771,2.031 0.271,0.167 10 #10 0.083,0.094 0.271,0.26 0.188,0.167 10 *a
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B77-20 (#10) - B77-50 (E01) Ignition switch ON 11 to 14 V
B77-17 (#20) - B77-50 (E01) Ignition switch ON 11 to 14 V
B77-18 (#30) - B77-50 (E01) Ignition switch ON 11 to 14 V
B77-19 (#40) - B77-50 (E01) Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG




OK

28.CHECK FUEL INJECTOR OF MISFIRING CYLINDER

NG

28.CHECK FUEL INJECTOR OF MISFIRING CYLINDER
a.

Check the fuel injector assembly injection (whether fuel volume is high or low, and whether injection pattern is poor).

Click hereEngine / Hybrid System>2AR-FE FUEL>FUEL INJECTOR>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the fuel injector assembly.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION



Result:
Proceed to
OK
NG



OK

29.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY CONNECTOR CONNECTION)

NG

REPLACE FUEL INJECTOR ASSEMBLY

29.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY CONNECTOR CONNECTION)
a.

Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter sub-assembly and ECM.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE

HINT:

Repair any problems.



Result:
Proceed to
NEXT



NEXT

30.CHECK WHETHER DTC OUTPUT RECURS (MISFIRE DTCS)
30.CHECK WHETHER DTC OUTPUT RECURS (MISFIRE DTCS)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Start the engine and warm it up.


i.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


j.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine and ECT > Utility
Tester Display
All Readiness
50005 234 1020

k.

Input the DTC: P0300, P0301, P0302, P0303 or P0304.


l.

Check the DTC judgment result.

Result:
Result Proceed to
ABNORMAL
(DTC P0300, P0301, P0302, P0303 or P0304 is output)
A
NORMAL
(DTC is not output)
B




A

31.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)

B

END

31.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)

OK

32.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

32.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY
a.

Replace the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>MASS AIR FLOW METER>REMOVAL

HINT:
·

If the results of the inspections performed in steps 16 and 22 indicated no problem, proceed to the next step without replacing the mass air flow meter sub-assembly.

·

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION




Result:
Proceed to
NEXT



NEXT

33.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
33.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Start the engine and warm it up.


i.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


j.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine and ECT > Utility
Tester Display
All Readiness
50005 234 1020

k.

Input the DTC: P0300, P0301, P0302, P0303 or P0304.


l.

Check the DTC judgment result.

Result:
Result Proceed to
NORMAL
(DTC is not output)
A
ABNORMAL
(DTC P0300, P0301, P0302, P0303 or P0304 is output)
B




A

END

B

34.CHECK FUEL LINE
a.

Check the fuel lines for leaks or blockage.

HINT:

Perform "Inspection After Repair" after replacing the fuel pump.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE FUEL LINE