Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2013.11–2015.10
RM3090E _58 Vehicle Interior _008784 METER / GAUGE / DISPLAY _0050254 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Speed Signal Circuit  


DESCRIPTION

The vehicle speed signal consists of pulses sent to the combination meter assembly from the brake actuator assembly (skid control ECU).

WIRING DIAGRAM

E291157E01
5.115,2.771 7.156,3.031 2.042,0.26 10 false Combination Meter Assembly 5.104,2.604 5.521,2.792 0.417,0.188 10 false G16 5.615,1.99 6.031,2.177 0.417,0.188 10 false +S 5.625,0.354 6.042,0.542 0.417,0.188 10 false SI 5.323,1.865 5.74,2.052 0.417,0.188 10 false 6 5.313,0.219 5.729,0.406 0.417,0.188 10 false 5 2,0.344 2.417,0.531 0.417,0.188 10 false A63 2.375,0.344 2.792,0.531 0.417,0.188 10 false A64 2.042,0.146 2.458,0.333 0.417,0.188 10 false 22 2.406,0.135 2.823,0.323 0.417,0.188 10 false 11 2.073,0.552 2.49,0.74 0.417,0.188 10 false *1 2.458,0.552 2.875,0.74 0.417,0.188 10 false *2 1.594,0.24 2.01,0.427 0.417,0.188 10 false SP1 0.219,1.094 3.333,1.406 3.115,0.313 10 false Brake Actuator Assembly (Skid Control ECU) 2.052,2 2.469,2.188 0.417,0.188 10 false G48 2.385,2 2.802,2.188 0.417,0.188 10 false G139 2.75,2 3.167,2.188 0.417,0.188 10 false G143 2.104,1.781 2.521,1.969 0.417,0.188 10 false 17 2.469,1.781 2.885,1.969 0.417,0.188 10 false 17 2.844,1.781 3.26,1.969 0.417,0.188 10 false 17 2.115,2.198 2.531,2.385 0.417,0.188 10 false *3 2.354,2.208 2.958,2.469 0.604,0.26 10 false *4, *14 2.906,2.208 3.323,2.396 0.417,0.188 10 false *5 0.333,2.302 2.375,2.563 2.042,0.26 10 false Radio Receiver Assembly*3 0.333,2.573 3.281,2.875 2.948,0.302 10 false Navigation ECU Sub-assembly*4 0.333,2.854 3.281,3.156 2.948,0.302 10 false Radio and Display Receiver Assembly*5 0.333,3.135 3.281,3.438 2.948,0.302 10 false Navigation Receiver Assembly*14 1.646,1.885 2.063,2.073 0.417,0.188 10 false SPD 0.396,4.354 2.823,4.604 2.427,0.25 10 false Windshield Wiper Relay Assembly*6 0.385,4.188 0.802,4.375 0.417,0.188 10 false G85 1.646,3.823 2.063,4.01 0.417,0.188 10 false SPD 2.083,3.823 2.5,4.01 0.417,0.188 10 false 24 5.75,3.823 6.167,4.01 0.417,0.188 10 false SPD 5.458,3.823 5.875,4.01 0.417,0.188 10 false 3 5.802,4.24 6.219,4.427 0.417,0.188 10 false B79 5.813,4.396 6.479,4.625 0.667,0.229 10 false TCM*9 0.396,5.688 2.823,5.938 2.427,0.25 10 false Headlight Leveling ECU Assembly*7 0.396,5.531 0.813,5.719 0.417,0.188 10 false A67 1.552,5.135 2.073,5.323 0.521,0.188 10 false SPDR 2.063,5.135 2.479,5.323 0.417,0.188 10 false 16 6.042,5.573 6.708,5.802 0.667,0.229 10 false ECM 5.74,5.146 6.146,5.375 0.406,0.229 10 false SPD 4.635,5.25 5.052,5.438 0.417,0.188 10 false A61 5.01,5.25 5.427,5.438 0.417,0.188 10 false A62 5.375,5.25 5.792,5.438 0.417,0.188 10 false A62 4.667,5.042 5.083,5.229 0.417,0.188 10 false 14 5.052,5.042 5.469,5.229 0.417,0.188 10 false 57 5.417,5.042 5.833,5.229 0.417,0.188 10 false 44 4.667,5.458 5.083,5.646 0.417,0.188 10 false *10 5.042,5.469 5.458,5.656 0.417,0.188 10 false *11 5.406,5.469 5.823,5.656 0.417,0.188 10 false *12 0.135,6.844 3.385,7.063 3.25,0.219 10 false Certification ECU (Smart Key ECU Assembly)*8 0.135,6.688 0.552,6.875 0.417,0.188 10 false G84 1.635,6.406 2.052,6.594 0.417,0.188 10 false SPD 2.083,6.406 2.5,6.594 0.417,0.188 10 false 27 4.406,6.844 7.156,7.063 2.75,0.219 10 false Stereo Component Amplifier Assembly*13 5.74,6.417 6.146,6.646 0.406,0.229 10 false SPD 5.396,6.417 5.813,6.604 0.417,0.188 10 false 11 4.406,6.698 4.823,6.885 0.417,0.188 10 false M32 0.031,7.146 1.198,7.396 1.167,0.25 10 false *1: w/o VSC 0.052,7.417 1.219,7.667 1.167,0.25 10 false *2: w/ VSC 0.052,7.688 2.229,7.958 2.177,0.271 10 false *3: for Radio Receiver Type 0.052,7.979 2.823,8.24 2.771,0.26 10 false *4: for Navigation Receiver Type (for HDD) 0.052,8.26 2.271,8.531 2.219,0.271 10 false *5: for Radio and Display Type 0.063,8.531 1.479,8.771 1.417,0.24 10 false *6: w/ Rain Sensor 2.656,7.167 4.542,7.594 1.885,0.427 10 false *7: w/ Automatic Headlight Beam Level Control System 2.646,7.76 4.708,8 2.063,0.24 10 false *8: w/ Entry and Start System 2.656,8.052 4.719,8.292 2.063,0.24 10 false *9: except Manual Transaxle 2.625,8.333 4.688,8.573 2.063,0.24 10 false *10: Engine Type Diesel 4.781,7.146 5.906,7.365 1.125,0.219 10 false *11: 2AR-FE 4.781,7.417 6.385,7.635 1.604,0.219 10 false *12: 3ZR-FE, 3ZR-FAE 4.792,7.677 6.396,7.896 1.604,0.219 10 false *13: for 11 Speakers 4.802,7.958 6.542,8.375 1.74,0.417 10 false *14: for Navigation Receiver Type (for SD)

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.

·

When replacing the combination meter assembly, make sure to replace it with a new one.



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Proceed to
for Radio and Display Type
for Navigation Receiver Type (for SD)
for Navigation Receiver Type (for HDD)
for Radio Receiver Type



for Radio and Display Type

2.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

for Navigation Receiver Type (for SD)

11.CHECK NAVIGATION RECEIVER ASSEMBLY

for Navigation Receiver Type (for HDD)

20.CHECK NAVIGATION ECU SUB-ASSEMBLY

for Radio Receiver Type

22.CHECK RADIO RECEIVER ASSEMBLY
2.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
E179098C03
0.104,1.177 0.542,1.417 0.438,0.24 0.896,0.479 1.104,0.479 1.104,0.479 1.292,1.188 false 0.156,0.073 0.333,0.24 0.177,0.167 10 *a 0.188,1.219 0.635,1.427 0.448,0.208 10 G16 0.667,0.396 0.875,0.542 0.208,0.146 10 +S
*a Front view of wire harness connector
(to Combination Meter Assembly)


*1: w/ Rain Sensor

*2: w/ Automatic Headlight Beam Level Control System

*3: w/ Entry and Start System

*4: except Manual Transaxle

*5: Engine Type Diesel

*6: Engine Type Gasoline

*7: for 11 Speakers


a.

Disconnect the G16 combination meter assembly connector.


b.

Disconnect the G85 windshield wiper relay assembly connector.*1


c.

Disconnect the A67 headlight leveling ECU assembly connector.*2


d.

Disconnect the G84 certification ECU (smart key ECU assembly) connector.*3


e.

Disconnect the B79 TCM connector.*4


f.

Disconnect the A61*5 or A62*6 ECM connector.


g.

Disconnect the M32 stereo component amplifier assembly connector.*7


h.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G16-6 (+S) - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

12.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)
3.CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY
NOTICE:

For vehicle except 11 speakers, proceed to next step.


E179098C03
0.104,1.177 0.542,1.417 0.438,0.24 0.896,0.479 1.104,0.479 1.104,0.479 1.292,1.188 false 0.156,0.073 0.333,0.24 0.177,0.167 10 *a 0.188,1.219 0.635,1.427 0.448,0.208 10 G16 0.667,0.396 0.875,0.542 0.208,0.146 10 +S
*a Front view of wire harness connector
(to Combination Meter Assembly)


*1: for Radio and Display Type

*2: for Navigation Receiver Type (for SD)

*3: w/ Rain Sensor

*4: w/ Automatic Headlight Beam Level Control System

*5: w/ Entry and Start System

*6: except Manual Transaxle

*7: Engine Type Diesel

*8: Engine Type Gasoline


a.

Disconnect the G16 combination meter assembly connector.


b.

Disconnect the G143 radio and display receiver assembly connector.*1


c.

Disconnect the G139 navigation receiver assembly connector.*2


d.

Disconnect the G85 windshield wiper relay assembly connector.*3


e.

Disconnect the A67 headlight leveling ECU assembly connector.*4


f.

Disconnect the G84 certification ECU (smart key ECU assembly) connector.*5


g.

Disconnect the B79 TCM connector.*6


h.

Disconnect the A61*7 or A62*8 ECM connector.


i.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G16-6 (+S) - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK WINDSHIELD WIPER RELAY ASSEMBLY

NG

13.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
4.CHECK WINDSHIELD WIPER RELAY ASSEMBLY
NOTICE:

For vehicle without a rain sensor, proceed to next step.


E179098C03
0.104,1.177 0.542,1.417 0.438,0.24 0.896,0.479 1.104,0.479 1.104,0.479 1.292,1.188 false 0.156,0.073 0.333,0.24 0.177,0.167 10 *a 0.188,1.219 0.635,1.427 0.448,0.208 10 G16 0.667,0.396 0.875,0.542 0.208,0.146 10 +S
*a Front view of wire harness connector
(to Combination Meter Assembly)


*1: for Radio Receiver Type

*2: for Navigation Receiver Type (for HDD)

*3: for Radio and Display Type

*4: w/ Automatic Headlight Beam Level Control System

*5: w/ Entry and Start System

*6: except Manual Transaxle

*7: Engine Type Diesel

*8: Engine Type Gasoline

*9: for Navigation Receiver Type (for SD)


a.

Disconnect the G16 combination meter assembly connector.


b.

Disconnect the G48 radio receiver assembly connector.*1


c.

Disconnect the G139 navigation ECU sub-assembly connector.*2


d.

Disconnect the G143 radio and display receiver assembly connector.*3


e.

Disconnect the G139 navigation receiver assembly connector.*9


f.

Disconnect the A67 headlight leveling ECU assembly connector.*4


g.

Disconnect the G84 certification ECU (smart key ECU assembly) connector.*5


h.

Disconnect the B79 TCM connector.*6


i.

Disconnect the A61*7 or A62*8 ECM connector.


j.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G16-6 (+S) - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HEADLIGHT LEVELING ECU ASSEMBLY

NG

14.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - WINDSHIELD WIPER RELAY ASSEMBLY)
5.CHECK HEADLIGHT LEVELING ECU ASSEMBLY
NOTICE:

For vehicle without an automatic headlight beam level control system, proceed to next step.


E179098C03
0.104,1.177 0.542,1.417 0.438,0.24 0.896,0.479 1.104,0.479 1.104,0.479 1.292,1.188 false 0.156,0.073 0.333,0.24 0.177,0.167 10 *a 0.188,1.219 0.635,1.427 0.448,0.208 10 G16 0.667,0.396 0.875,0.542 0.208,0.146 10 +S
*a Front view of wire harness connector
(to Combination Meter Assembly)


*1: for Radio Receiver Type

*2: for Navigation Receiver Type (for HDD)

*3: for Radio and Display Type

*4: w/ Rain Sensor

*5: w/ Entry and Start System

*6: except Manual Transaxle

*7: Engine Type Diesel

*8: Engine Type Gasoline

*9: for Navigation Receiver Type (for SD)


a.

Disconnect the G16 combination meter assembly connector.


b.

Disconnect the G48 radio receiver assembly connector.*1


c.

Disconnect the G139 navigation ECU sub-assembly connector.*2


d.

Disconnect the G143 radio and display receiver assembly connector.*3


e.

Disconnect the G139 navigation receiver assembly connector.*9


f.

Disconnect the G85 windshield wiper relay assembly connector.*4


g.

Disconnect the G84 certification ECU (smart key ECU assembly) connector.*5


h.

Disconnect the B79 TCM connector.*6


i.

Disconnect the A61*7 or A62*8 ECM connector.


j.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G16-6 (+S) - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

15.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - HEADLIGHT LEVELING ECU)
6.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
NOTICE:

For vehicle without an entry and start system, proceed to next step.


E179098C03
0.104,1.177 0.542,1.417 0.438,0.24 0.896,0.479 1.104,0.479 1.104,0.479 1.292,1.188 false 0.156,0.073 0.333,0.24 0.177,0.167 10 *a 0.188,1.219 0.635,1.427 0.448,0.208 10 G16 0.667,0.396 0.875,0.542 0.208,0.146 10 +S
*a Front view of wire harness connector
(to Combination Meter Assembly)


*1: for Radio Receiver Type

*2: for Navigation Receiver Type (for HDD)

*3: for Radio and Display Type

*4: w/ Rain Sensor

*5: w/ Automatic Headlight Beam Level Control System

*6: except Manual Transaxle

*7: Engine Type Diesel

*8: Engine Type Gasoline

*9: for Navigation Receiver Type (for SD)


a.

Disconnect the G16 combination meter assembly connector.


b.

Disconnect the G48 radio receiver assembly connector.*1


c.

Disconnect the G139 navigation ECU sub-assembly connector.*2


d.

Disconnect the G143 radio and display receiver assembly connector.*3


e.

Disconnect the G139 navigation receiver assembly connector.*9


f.

Disconnect the G85 windshield wiper relay assembly connector.*4


g.

Disconnect the A67 headlight leveling ECU assembly connector.*5


h.

Disconnect the B79 TCM connector.*6


i.

Disconnect the A61*7 or A62*8 ECM connector.


j.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G16-6 (+S) - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

7.CHECK TCM

NG

16.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])
7.CHECK TCM
NOTICE:

For vehicle manual transaxle, proceed to next step.


E179098C03
0.104,1.177 0.542,1.417 0.438,0.24 0.896,0.479 1.104,0.479 1.104,0.479 1.292,1.188 false 0.156,0.073 0.333,0.24 0.177,0.167 10 *a 0.188,1.219 0.635,1.427 0.448,0.208 10 G16 0.667,0.396 0.875,0.542 0.208,0.146 10 +S
*a Front view of wire harness connector
(to Combination Meter Assembly)


*1: for Radio Receiver Type

*2: for Navigation Receiver Type (for HDD)

*3: for Radio and Display Type

*4: w/ Rain Sensor

*5: w/ Automatic Headlight Beam Level Control System

*6: w/ Entry and Start System

*7: Engine Type Diesel

*8: Engine Type Gasoline

*9: for Navigation Receiver Type (for SD)


a.

Disconnect the G16 combination meter assembly connector.


b.

Disconnect the G48 radio receiver assembly connector.*1


c.

Disconnect the G139 navigation ECU sub-assembly connector.*2


d.

Disconnect the G143 radio and display receiver assembly connector.*3


e.

Disconnect the G139 navigation receiver assembly connector.*9


f.

Disconnect the G85 windshield wiper relay assembly connector.*4


g.

Disconnect the A67 headlight leveling ECU assembly connector.*5


h.

Disconnect the G84 certification ECU (smart key ECU assembly) connector.*6


i.

Disconnect the A61*7 or A62*8 ECM connector.


j.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G16-6 (+S) - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

8.CHECK ECM

NG

17.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])
8.CHECK ECM
E179098C03
0.104,1.177 0.542,1.417 0.438,0.24 0.896,0.479 1.104,0.479 1.104,0.479 1.292,1.188 false 0.156,0.073 0.333,0.24 0.177,0.167 10 *a 0.188,1.219 0.635,1.427 0.448,0.208 10 G16 0.667,0.396 0.875,0.542 0.208,0.146 10 +S
*a Front view of wire harness connector
(to Combination Meter Assembly)


*1: for Radio Receiver Type

*2: for Navigation Receiver Type (for HDD)

*3: for Radio and Display Type

*4: w/ Rain Sensor

*5: w/ Automatic Headlight Beam Level Control System

*6: w/ Entry and Start System

*7: except Manual Transaxle

*8: for Navigation Receiver Type (for SD)


a.

Disconnect the G16 combination meter assembly connector.


b.

Disconnect the G48 radio receiver assembly connector.*1


c.

Disconnect the G139 navigation ECU sub-assembly connector.*2


d.

Disconnect the G143 radio and display receiver assembly connector.*3


e.

Disconnect the G139 navigation receiver assembly connector.*8


f.

Disconnect the G85 windshield wiper relay assembly connector.*4


g.

Disconnect the A67 headlight leveling ECU assembly connector.*5


h.

Disconnect the G84 certification ECU (smart key ECU assembly) connector.*6


i.

Disconnect the B79 TCM connector.*7


j.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G16-6 (+S) - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

9.CHECK COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)

NG

18.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])
9.CHECK COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)
E235636C02
0.042,0.813 0.396,1.031 0.354,0.219 0.042,1.094 0.396,1.313 0.354,0.219 2.104,0.969 2.271,0.219 2.271,0.219 2.438,0.219 false 2.021,1.198 2.51,1.938 2.51,1.938 2.677,1.938 false 0.125,0.094 0.438,0.292 0.313,0.198 10 *a 2.719,1.854 3.25,2.052 0.531,0.198 10 SP1*A 0.094,0.844 0.417,1.042 0.323,0.198 10 A63 0.104,1.125 0.417,1.323 0.313,0.198 10 A64 0.458,0.865 0.771,1.063 0.313,0.198 10 *A 0.458,1.125 0.771,1.323 0.313,0.198 10 *B 2.479,0.135 3.01,0.333 0.531,0.198 10 SP1*B
*A w/o VSC
*B w/ VSC
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


*1: w/o VSC

*2: w/VSC


a.

Disconnect the A63*1 or A64*2 brake actuator assembly (skid control ECU) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
w/o VSC
Tester Connection Switch Condition Specified Condition
A63-22 (SP1) - Body ground Ignition switch ON 11 to 14 V

w/ VSC
Tester Connection Switch Condition Specified Condition
A64-11 (SP1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

10.CHECK COMBINATION METER ASSEMBLY (SPEED SIGNAL)

NG

19.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU])
10.CHECK COMBINATION METER ASSEMBLY (SPEED SIGNAL)
E200403C06
0.177,0.969 0.573,1.188 0.396,0.219 2.708,0.365 2.531,0.365 2.531,0.365 2.219,1.094 false 2.771,0.302 2.938,0.448 0.167,0.146 10 false SI 0.24,1.01 0.604,1.198 0.365,0.188 10 false G16 1.333,4.094 1.458,4.24 0.125,0.146 10 false A 2.969,3.521 3.302,3.667 0.333,0.146 10 false GND 0.135,0.115 0.438,0.313 0.302,0.198 10 false *a
*a Component with harness connected
(Combination Meter Assembly)


a.

Remove the combination meter assembly with the connector(s) still connected.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


b.

Connect an oscilloscope to terminal G16-5 (SI) and body ground.


c.

Check the signal waveform according to the condition(s) in the table below.

Measurement Condition
Item Condition
Tester Connection G16-5 (SI) - Body ground
Tool Setting 5 V/DIV., 20 ms./DIV.
Vehicle Condition Driving at approximately 20 km/h (12 mph)

HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by A in the illustration narrows.


OK:

The waveform displayed is as shown in the illustration.



Result:
Proceed to
OK
NG (w/o VSC)
NG (w/ VSC)



OK

REPLACE COMBINATION METER ASSEMBLY

NG (w/o VSC)

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

NG (w/ VSC)

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

11.CHECK NAVIGATION RECEIVER ASSEMBLY
E179098C03
0.104,1.177 0.542,1.417 0.438,0.24 0.896,0.479 1.104,0.479 1.104,0.479 1.292,1.188 false 0.156,0.073 0.333,0.24 0.177,0.167 10 *a 0.188,1.219 0.635,1.427 0.448,0.208 10 G16 0.667,0.396 0.875,0.542 0.208,0.146 10 +S
*a Front view of wire harness connector
(to Combination Meter Assembly)


*1: w/ Rain Sensor

*2: w/ Automatic Headlight Beam Level Control System

*3: w/ Entry and Start System

*4: except Manual Transaxle

*5: Engine Type Diesel

*6: Engine Type Gasoline


a.

Disconnect the G16 combination meter assembly connector.


b.

Disconnect the G85 windshield wiper relay assembly connector.*1


c.

Disconnect the A67 headlight leveling ECU assembly connector.*2


d.

Disconnect the G84 certification ECU (smart key ECU assembly) connector.*3


e.

Disconnect the B79 TCM connector.*4


f.

Disconnect the A61*5 or A62*6 ECM connector.


g.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G16-6 (+S) - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

21.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NAVIGATION RECEIVER ASSEMBLY)
12.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)

*1: w/ Rain Sensor

*2: w/ Automatic Headlight Beam Level Control System

*3: w/ Entry and Start System

*4: except Manual Transaxle

*5: Engine Type Diesel

*6: Engine Type Gasoline

*7: for 11 Speakers


a.

Disconnect the G16 combination meter assembly connector.


b.

Disconnect the G143 radio and display receiver assembly connector.


c.

Disconnect the G85 windshield wiper relay assembly connector.*1


d.

Disconnect the A67 headlight leveling ECU assembly connector.*2


e.

Disconnect the G84 certification ECU (smart key ECU assembly) connector.*3


f.

Disconnect the B79 TCM connector.*4


g.

Disconnect the A61*5 or A62*6 ECM connector.


h.

Disconnect the M32 stereo component amplifier assembly connector.*7


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-6 (+S) - G143-17 (SPD) Always Below 1 Ω
G16-6 (+S) or G143-17 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)

*1: for Radio and Display Type

*2: for Navigation Receiver Type (for SD)

*3: w/ Rain Sensor

*4: w/ Automatic Headlight Beam Level Control System

*5: w/ Entry and Start System

*6: except Manual Transaxle

*7: Engine Type Diesel

*8: Engine Type Gasoline


a.

Disconnect the G16 combination meter assembly connector.


b.

Disconnect the M32 stereo component amplifier assembly connector.


c.

Disconnect the G143 radio and display receiver assembly connector.*1


d.

Disconnect the G139 navigation receiver assembly connector.*2


e.

Disconnect the G85 windshield wiper relay assembly connector.*3


f.

Disconnect the A67 headlight leveling ECU assembly connector.*4


g.

Disconnect the G84 certification ECU (smart key ECU assembly) connector.*5


h.

Disconnect the B79 TCM connector.*6


i.

Disconnect the A61*7 or A62*8 ECM connector.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-6 (+S) - M32-11 (SPD) Always Below 1 Ω
G16-6 (+S) or M32-11 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - WINDSHIELD WIPER RELAY ASSEMBLY)

*1: for Radio Receiver Type

*2: for Navigation Receiver Type (for HDD)

*3: for Radio and Display Type

*4: w/ Automatic Headlight Beam Level Control System

*5: w/ Entry and Start System

*6: except Manual Transaxle

*7: Engine Type Diesel

*8: Engine Type Gasoline

*9: for Navigation Receiver Type (for SD)


a.

Disconnect the G16 combination meter assembly connector.


b.

Disconnect the G85 windshield wiper relay assembly connector.


c.

Disconnect the G48 radio receiver assembly connector.*1


d.

Disconnect the G139 navigation ECU sub-assembly connector.*2


e.

Disconnect the G143 radio and display receiver assembly connector.*3


f.

Disconnect the G139 navigation receiver connector.*9


g.

Disconnect the A67 headlight leveling ECU assembly connector.*4


h.

Disconnect the G84 certification ECU (smart key ECU assembly) connector.*5


i.

Disconnect the B79 TCM connector.*6


j.

Disconnect the A61*7 or A62*8 ECM connector.


k.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-6 (+S) - G85-24 (SPD) Always Below 1 Ω
G16-6 (+S) or G85-24 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE WINDSHIELD WIPER RELAY ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - HEADLIGHT LEVELING ECU)

*1: for Radio Receiver Type

*2: for Navigation Receiver Type (for HDD)

*3: for Radio and Display Type

*4: w/ Rain Sensor

*5: w/ Entry and Start System

*6: except Manual Transaxle

*7: Engine Type Diesel

*8: Engine Type Gasoline

*9: for Navigation Receiver Type (for SD)


a.

Disconnect the G16 combination meter assembly connector.


b.

Disconnect the A67 headlight leveling ECU assembly connector.


c.

Disconnect the G48 radio receiver assembly connector.*1


d.

Disconnect the G139 navigation ECU sub-assembly connector.*2


e.

Disconnect the G143 radio and display receiver assembly connector.*3


f.

Disconnect the G139 navigation receiver assembly connector.*9


g.

Disconnect the G85 windshield wiper relay assembly connector.*4


h.

Disconnect the G84 certification ECU (smart key ECU assembly) connector.*5


i.

Disconnect the B79 TCM connector.*6


j.

Disconnect the A61*7 or A62*8 ECM connector.


k.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-6 (+S) - A67-16 (SPDR) Always Below 1 Ω
G16-6 (+S) or A67-16 (SPDR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])

*1: for Radio Receiver Type

*2: for Navigation Receiver Type (for HDD)

*3: for Radio and Display Type

*4: w/ Rain Sensor

*5: w/ Automatic Headlight Beam Level Control System

*6: except Manual Transaxle

*7: Engine Type Diesel

*8: Engine Type Gasoline

*9: for Navigation Receiver Type (for SD)


a.

Disconnect the G16 combination meter assembly connector.


b.

Disconnect the G84 certification ECU (smart key ECU assembly) connector.


c.

Disconnect the G48 radio receiver assembly connector.*1


d.

Disconnect the G139 navigation ECU sub-assembly connector.*2


e.

Disconnect the G143 radio and display receiver assembly connector.*3


f.

Disconnect the G139 navigation receiver assembly connector.*9


g.

Disconnect the G85 windshield wiper relay assembly connector.*4


h.

Disconnect the A67 headlight leveling ECU assembly connector.*5


i.

Disconnect the B79 TCM connector.*6


j.

Disconnect the A61*7 or A62*8 ECM connector.


k.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-6 (+S) - A67-16 (SPDR) Always Below 1 Ω
G16-6 (+S) or A67-16 (SPDR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])

*1: for Radio Receiver Type

*2: for Navigation Receiver Type (for HDD)

*3: for Radio and Display Type

*4: w/ Rain Sensor

*5: w/ Automatic Headlight Beam Level Control System

*6: w/ Entry and Start System

*7: Engine Type Diesel

*8: Engine Type Gasoline

*9: for Navigation Receiver Type (for SD)


a.

Disconnect the G16 combination meter assembly connector.


b.

Disconnect the B79 TCM connector.


c.

Disconnect the G48 radio receiver assembly connector.*1


d.

Disconnect the G139 navigation ECU sub-assembly connector.*2


e.

Disconnect the G143 radio and display receiver assembly connector.*3


f.

Disconnect the G139 navigation receiver assembly connector.*9


g.

Disconnect the G85 windshield wiper relay assembly connector.*4


h.

Disconnect the A67 headlight leveling ECU assembly connector.*5


i.

Disconnect the G84 certification ECU (smart key ECU assembly) connector.*6


j.

Disconnect the A61*7 or A62*8 ECM connector.


k.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-6 (+S) - B79-3 (SPD) Always Below 1 Ω
G16-6 (+S) or B79-3 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK (U660F)
OK (U760E)
OK (U760F)
OK (K111)
OK (K111F)
NG



OK (U660F)

OK (U760E)

OK (U760F)

OK (K111)

OK (K111F)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])

*1: Engine Type Diesel

*2: Engine Type Gasoline

*3: for Radio Receiver Type

*4: for Navigation Receiver Type (for HDD)

*5: for Radio and Display Type

*6: w/ Rain Sensor

*7: w/ Automatic Headlight Beam Level Control System

*8: w/ Entry and Start System

*9: except Manual Transaxle

*10: for Navigation Receiver Type (for SD)


a.

Disconnect the G16 combination meter assembly connector.


b.

Disconnect the A61*1 or A62*2 ECM connector.


c.

Disconnect the G48 radio receiver assembly connector.*3


d.

Disconnect the G139 navigation ECU sub-assembly connector.*4


e.

Disconnect the G143 radio and display receiver assembly connector.*5


f.

Disconnect the G139 navigation receiver assembly connector.*10


g.

Disconnect the G85 windshield wiper relay assembly connector.*6


h.

Disconnect the A67 headlight leveling ECU assembly connector.*7


i.

Disconnect the G84 certification ECU (smart key ECU assembly) connector.*8


j.

Disconnect the B79 TCM connector.*9


k.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Engine Type Diesel
Tester Connection Condition Specified Condition
G16-6 (+S) - A61-14 (SPD) Always Below 1 Ω
G16-6 (+S) or A61-14 (SPD) - Body ground Always 10 kΩ or higher

2AR-FE
Tester Connection Condition Specified Condition
G16-6 (+S) - A62-57 (SPD) Always Below 1 Ω
G16-6 (+S) or A62-57 (SPD) - Body ground Always 10 kΩ or higher

3ZR-FE, 3ZR-FAE
Tester Connection Condition Specified Condition
G16-6 (+S) - A62-44 (SPD) Always Below 1 Ω
G16-6 (+S) or A62-44 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK (1AD-FTV)
OK (2AD-FHV)
OK (2AD-FTV)
OK (2AR-FE)
OK (3ZR-FAE)
OK (3ZR-FE)
NG



OK (1AD-FTV)

OK (2AD-FHV)

OK (2AD-FTV)

OK (2AR-FE)

OK (3ZR-FAE)

OK (3ZR-FE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU])
a.

Disconnect the G16 combination meter assembly connector.


b.

Disconnect the A63*1 or A64*2 brake actuator assembly (skid control ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o VSC
Tester Connection Condition Specified Condition
G16-5 (SI) - A63-22 (SP1) Always Below 1 Ω
G16-5 (SI) or A63-22 (SP1) - Body ground Always 10 kΩ or higher

w/ VSC
Tester Connection Condition Specified Condition
G16-5 (SI) - A64-11 (SP1) Always Below 1 Ω
G16-5 (SI) or A64-11 (SP1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.CHECK NAVIGATION ECU SUB-ASSEMBLY
E179098C03
0.104,1.177 0.542,1.417 0.438,0.24 0.896,0.479 1.104,0.479 1.104,0.479 1.292,1.188 false 0.156,0.073 0.333,0.24 0.177,0.167 10 *a 0.188,1.219 0.635,1.427 0.448,0.208 10 G16 0.667,0.396 0.875,0.542 0.208,0.146 10 +S
*a Front view of wire harness connector
(to Combination Meter Assembly)


*1: w/ Rain Sensor

*2: w/ Automatic Headlight Beam Level Control System

*3: w/ Entry and Start System

*4: except Manual Transaxle

*5: Engine Type Diesel

*6: Engine Type Gasoline


a.

Disconnect the G16 combination meter assembly connector.


b.

Disconnect the G85 windshield wiper relay assembly connector.*1


c.

Disconnect the A67 headlight leveling ECU assembly connector.*2


d.

Disconnect the G84 certification ECU (smart key ECU assembly) connector.*3


e.

Disconnect the B79 TCM connector.*4


f.

Disconnect the A61*5 or A62*6 ECM connector.


g.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G16-6 (+S) - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK WINDSHIELD WIPER RELAY ASSEMBLY

NG

23.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NAVIGATION ECU SUB-ASSEMBLY)
21.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NAVIGATION RECEIVER ASSEMBLY)

*1: w/ Rain Sensor

*2: w/ Automatic Headlight Beam Level Control System

*3: w/ Entry and Start System

*4: except Manual Transaxle

*5: Engine Type Diesel

*6: Engine Type Gasoline


a.

Disconnect the G16 combination meter assembly connector.


b.

Disconnect the G139 navigation receiver assembly connector.


c.

Disconnect the G85 windshield wiper relay assembly connector.*1


d.

Disconnect the A67 headlight leveling ECU assembly connector.*2


e.

Disconnect the G84 certification ECU (smart key ECU assembly) connector.*3


f.

Disconnect the B79 TCM connector.*4


g.

Disconnect the A61*5 or A62*6 ECM connector.


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-6 (+S) - G139-17 (SPD) Always Below 1 Ω
G16-6 (+S) or G139-17 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

22.CHECK RADIO RECEIVER ASSEMBLY
E179098C03
0.104,1.177 0.542,1.417 0.438,0.24 0.896,0.479 1.104,0.479 1.104,0.479 1.292,1.188 false 0.156,0.073 0.333,0.24 0.177,0.167 10 *a 0.188,1.219 0.635,1.427 0.448,0.208 10 G16 0.667,0.396 0.875,0.542 0.208,0.146 10 +S
*a Front view of wire harness connector
(to Combination Meter Assembly)


*1: w/ Rain Sensor

*2: w/ Automatic Headlight Beam Level Control System

*3: w/ Entry and Start System

*4: except Manual Transaxle

*5: Engine Type Diesel

*6: Engine Type Gasoline


a.

Disconnect the G16 combination meter assembly connector.


b.

Disconnect the G85 windshield wiper relay assembly connector.*1


c.

Disconnect the A67 headlight leveling ECU assembly connector.*2


d.

Disconnect the G84 certification ECU (smart key ECU assembly) connector.*3


e.

Disconnect the B79 TCM connector.*4


f.

Disconnect the A61*5 or A62*6 ECM connector.


g.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G16-6 (+S) - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK WINDSHIELD WIPER RELAY ASSEMBLY

NG

24.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - RADIO RECEIVER ASSEMBLY)
23.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NAVIGATION ECU SUB-ASSEMBLY)

*1: w/ Rain Sensor

*2: w/ Automatic Headlight Beam Level Control System

*3: w/ Entry and Start System

*4: except Manual Transaxle

*5: Engine Type Diesel

*6: Engine Type Gasoline


a.

Disconnect the G16 combination meter assembly connector.


b.

Disconnect the G139 navigation receiver assembly connector.


c.

Disconnect the G85 windshield wiper relay assembly connector.*1


d.

Disconnect the A67 headlight leveling ECU assembly connector.*2


e.

Disconnect the G84 certification ECU (smart key ECU assembly) connector.*3


f.

Disconnect the B79 TCM connector.*4


g.

Disconnect the A61*5 or A62*6 ECM connector.


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-6 (+S) - G139-17 (SPD) Always Below 1 Ω
G16-6 (+S) or G139-17 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE NAVIGATION ECU SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

24.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - RADIO RECEIVER ASSEMBLY)

*1: w/ Rain Sensor

*2: w/ Automatic Headlight Beam Level Control System

*3: w/ Entry and Start System

*4: except Manual Transaxle

*5: Engine Type Diesel

*6: Engine Type Gasoline


a.

Disconnect the G16 combination meter assembly connector.


b.

Disconnect the G48 radio receiver assembly connector.


c.

Disconnect the G85 windshield wiper relay assembly connector.*1


d.

Disconnect the A67 headlight leveling ECU assembly connector.*2


e.

Disconnect the G84 certification ECU (smart key ECU assembly) connector.*3


f.

Disconnect the B79 TCM connector.*4


g.

Disconnect the A61*5 or A62*6 ECM connector.


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-6 (+S) - G48-17 (SPD) Always Below 1 Ω
G16-6 (+S) or G48-17 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE RADIO RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR