Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P00BD  Mass or Volume Air Flow "A" Circuit Range/Performance - Air Flow Too High  


DESCRIPTION

HINT:

For more information on the EGR control, refer to System Description.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>SYSTEM DESCRIPTION


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P00BD Mass or Volume Air Flow "A" Circuit Range/Performance - Air Flow Too High Either condition is met (3 trip detection logic):
·

Measured air mass compared with calculated air mass too high for 5 seconds.

·

Measured air mass compared with calculated air mass too high and high boost pressure deviation for 5 seconds.


·

Intake system air leak

·

Intake air temperature sensor

·

EGR valve assembly

·

EGR cooler assembly

·

Turbo pressure sensor assembly

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P00BD
·

Target EGR Position

·

Actual EGR Valve Pos

·

Intake Air Temp (Turbo)



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

After replacing the EGR valve assembly, the ECM needs initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning V alues Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

d.

Read the DTCs.

Result:
Result Proceed to
DTC P00BD A
DTC P00BD and other DTCs B




A

2.CHECK INTAKE AIR TEMPERATURE SENSOR

B

2.CHECK INTAKE AIR TEMPERATURE SENSOR
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air Temp (Turbo).

Powertrain > Engine and ECT > Data List
Tester Display
Intake Air Temp (Turbo)
50003 371 54
OK:

A value excessively higher than the actual intake air temperature is not displayed.



Result:
Proceed to
OK
NG



OK

3.CHECK TURBO PRESSURE SENSOR ASSEMBLY

NG

13.REPLACE INTAKE AIR TEMPERATURE SENSOR
3.CHECK TURBO PRESSURE SENSOR ASSEMBLY
a.

Check for DTCs related to the turbo pressure sensor assembly.


Result:
Proceed to
OK
NG



OK

4.CHECK INTAKE SYSTEM

NG

12.REPAIR OR REPLACE TURBO PRESSURE SENSOR ASSEMBLY
4.CHECK INTAKE SYSTEM
a.

Start the engine.


b.

Check air duct between intake silencer, mass air flow meter sub-assembly and turbocharger for leaks.


c.

Check air duct between turbocharger and intake manifold for leaks.

HINT:
·

Oily patches are signs of leaks.

·

Check whether sealing rings on charge air hoses are rolled back or missing.



OK:

No leakage.



Result:
Proceed to
OK
NG



OK

5.PERFORM ACTIVE TEST USING GTS (ACTUATOR TEST OF EGR-VALVE)

NG

11.REPAIR OR REPLACE INTAKE SYSTEM
5.PERFORM ACTIVE TEST USING GTS (ACTUATOR TEST OF EGR-VALVE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Actuator Test of EGR-Valve / Data List / Target EGR Position and Actual EGR Valve Pos.

Powertrain > Engine and ECT > Active Test
Active Test Display
Actuator Test of EGR-Valve
Data List Display
Target EGR Position
Actual EGR Valve Pos
50004 371 2 18,24

e.

Perform the following steps 1 to 4.


f.

Step 1

i.

Perform Actuator Test of EGR-Valve with control value of 0% (opening ratio in %).


ii.

Monitor the difference of the control value and EGR valve Actuator Position value (0 +/- 3%). EGR valve must operate within 1 second.



g.

Step 2

i.

Wait for 2 seconds or more.



h.

Step 3

i.

Perform Actuator Test of EGR-Valve with control value of 94% (opening ratio in %).


ii.

Monitor the difference of the control value and EGR valve Actuator Position value (0 +/- 3%). EGR valve must operate within 1 second.



i.

Step 4

i.

Wait for 2 seconds or more.



j.

Perform the above steps 1 to 4 and check that the part operates as specified.

OK:

Part operates as specified.


HINT:
·

If DTCs P00BD, P042F or P1268 is output, there may be a malfunction in the EGR system.

·

This inspection is primarily to check that the EGR valve is not clogged with soot and not stuck closed.




Result:
Proceed to
OK
NG



OK

6.CHECK EGR COOLER ASSEMBLY

NG

10.REPLACE EGR VALVE ASSEMBLY
6.CHECK EGR COOLER ASSEMBLY
a.

b.

Check that the airflow is not slowed by soot deposits in the EGR cooler.

OK:

Airflow is not slowed by soot deposits.


HINT:

If a malfunction is detected during this inspection, soot deposits may be accumulating in the EGR cooler.



Result:
Proceed to
OK
NG



OK

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P00BD)

NG

9.REPAIR OR REPLACE EGR COOLER ASSEMBLY
7.CHECK WHETHER DTC OUTPUT RECURS (DTC P00BD)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Read the DTCs.

Result:
Result Proceed to
No DTC A
DTC P00BD B




A

END

B

8.REPLACE ECM
8.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.REPAIR OR REPLACE EGR COOLER ASSEMBLY
a.

Clean the EGR cooler assembly.


b.

If soot deposits cannot be removed, replace the EGR cooler assembly.

Click hereEngine / Hybrid System>2WW EMISSION CONTROL>EGR COOLER>REMOVAL


Result:
Proceed to
NEXT



NEXT

14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.REPLACE EGR VALVE ASSEMBLY
a.

Replace the EGR valve assembly.

Click hereEngine / Hybrid System>2WW EMISSION CONTROL>EGR VALVE>REMOVAL


b.

Perform EGR learning value reset.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.REPAIR OR REPLACE INTAKE SYSTEM
a.

Repair or replace the malfunctioning parts of the intake system.


Result:
Proceed to
NEXT



NEXT

14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.REPAIR OR REPLACE TURBO PRESSURE SENSOR ASSEMBLY
a.

Repair or replace turbo pressure sensor assembly or perform inspections and troubleshooting for related DTCs.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>DIAGNOSTIC TROUBLE CODE CHART

HINT:

When the turbo pressure sensor assembly is replaced, perform initialization.



Result:
Proceed to
NEXT



NEXT

14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
13.REPLACE INTAKE AIR TEMPERATURE SENSOR
a.

Replace the intake air temperature sensor.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>INTAKE AIR TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END