Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P0101  Mass or Volume Air Flow Sensor "A" Circuit Range / Performance  


DESCRIPTION

Refer to DTC P0102.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>P0102

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0101 Mass or Volume Air Flow Sensor "A" Circuit Range / Performance When difference between mass air flow meter sub-assembly reading and estimated MAF exceeds threshold.
(3 trip detection logic)
·

Open or short in mass air flow meter sub-assembly circuit

·

Mass air flow meter sub-assembly

·

Intake air temperature sensor

·

Intake air duct

·

Air cleaner filter element sub-assembly

·

EGR valve assembly

·

Diesel throttle body assembly

·

Coking in intake ports and intake valves

·

Swirl control valve

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0101
·

Intake Air

·

Intake Air Temp (Turbo)



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

After replacing the mass air flow meter sub-assembly, the ECM needs initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

After replacing the swirl control valve, the ECM needs initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning V alues Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (INTAKE AIR AND INTAKE AIR TEMP (TURBO))
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air and Intake Air Temp (Turbo).

Powertrain > Engine and ECT > Data List
Tester Display
Intake Air
Intake Air Temp (Turbo)
50003 371 4,54

d.

Start the engine and wait 30 seconds.


e.

Read the value.

OK:

Difference between Intake Air and Intake Air Temp (Turbo) is 25°C (45°F) or less.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)

NG

20.REPLACE INTAKE AIR TEMPERATURE SENSOR
2.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B113-5 (VG) - B112-97 (VG) Always Below 1 Ω
B113-4 (VGR) - B112-98 (VGR) Always Below 1 Ω
B113-2 (E2G) - B112-129 (EVG) Always Below 1 Ω
B113-5 (VG) or B112-97 (VG) - Body ground Always 10 kΩ or higher
B113-4 (VGR) or B112-98 (VGR) - Body ground Always 10 kΩ or higher
B113-2 (E2G) or B112-129 (EVG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

NG

19.REPAIR OR REPLACE HARNESS OR CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - EFI MAIN NO. 1 RELAY OR ECM POWER SOURCE CIRCUIT)
3.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
A351157C04
0.188,1.021 0.604,1.313 0.417,0.292 2.333,1.281 2.625,1.552 false 0.417,0.302 0.729,0.458 0.313,0.156 10 false *a 0.24,1.094 0.667,1.344 0.427,0.25 10 false B113 2.698,1.51 3.125,1.76 0.427,0.25 10 false +B
*a Front view of wire harness connector
(to Mass Air Flow Meter Sub-assembly)


a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B113-1 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK INTAKE SYSTEM

NG

19.REPAIR OR REPLACE HARNESS OR CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - EFI MAIN NO. 1 RELAY OR ECM POWER SOURCE CIRCUIT)
4.CHECK INTAKE SYSTEM
a.

Start the engine.


b.

Check air duct between intake silencer, mass air flow meter sub-assembly and turbocharger for leaks.


c.

Check air duct between turbocharger and intake manifold for leaks.

HINT:
·

Oily patches are signs of leaks.

·

Check whether sealing rings on charge air hoses are rolled back or missing.



OK:

No leakage.



Result:
Proceed to
OK
NG



OK

5.CHECK AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

NG

18.REPAIR OR REPLACE INTAKE SYSTEM
5.CHECK AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
a.

Inspect the air cleaner filter element sub-assembly.

OK:

No blockage in air cleaner filter element sub-assembly.



Result:
Proceed to
OK
NG



OK

6.CHECK EGR VALVE ASSEMBLY

NG

17.REPLACE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
6.CHECK EGR VALVE ASSEMBLY
a.

Check that the there is no catching in the EGR valve assembly and installed parts have not been excessively tightened.


b.

Check for DTCs related to the EGR valve assembly.

OK:

There is no catching in the EGR valve assembly, installed parts have not been excessively tightened and no DTCs are stored.



Result:
Proceed to
OK
NG



OK

7.CHECK SWIRL CONTROL VALVE

NG

16.REPAIR OR REPLACE EGR VALVE ASSEMBLY
7.CHECK SWIRL CONTROL VALVE
a.

Check operation of swirl flaps and fault code memory entries.

OK:

DTCs are not stored and function operates normally.



Result:
Proceed to
OK
NG



OK

8.CHECK DIESEL THROTTLE BODY ASSEMBLY

NG

15.REPLACE SWIRL CONTROL VALVE
8.CHECK DIESEL THROTTLE BODY ASSEMBLY
a.

Check for DTCs related to the diesel throttle body assembly function.

OK:

DTCs are not stored and function operates normally.



Result:
Proceed to
OK
NG



OK

9.CHECK INTAKE PORT AND INTAKE VALVES

NG

14.REPAIR OR REPLACE DIESEL THROTTLE BODY ASSEMBLY
9.CHECK INTAKE PORT AND INTAKE VALVES
a.

Check intake ports and intake valves for coking.

HINT:

Excessive oil loss from crankcase ventilation system can cause coking, especially when in the case of short-distance driving.


OK:

Intake ports and intake valves are not coked.



Result:
Proceed to
OK
NG



OK

10.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

NG

13.CLEAN INTAKE PORT AND INTAKE VALVES
10.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY
a.

Replace the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>MASS AIR FLOW METER>REMOVAL


b.

Perform the mass air flow meter sub-assembly learning value reset.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

11.CHECK WHETHER DTC OUTPUT RECURS (DTC P0101)
11.CHECK WHETHER DTC OUTPUT RECURS (DTC P0101)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Read the DTCs.

Result:
Result Proceed to
No DTC output A
DTC P0101 B




A

END

B

12.REPLACE ECM
12.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

21.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
13.CLEAN INTAKE PORT AND INTAKE VALVES
a.

Clean coke from the intake ports and intake valves.


Result:
Proceed to
NEXT



NEXT

21.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
14.REPAIR OR REPLACE DIESEL THROTTLE BODY ASSEMBLY
a.

Repair or replace diesel throttle body assembly or perform inspections and troubleshooting for related DTCs.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>DIAGNOSTIC TROUBLE CODE CHART


Result:
Proceed to
NEXT



NEXT

21.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
15.REPLACE SWIRL CONTROL VALVE
a.

Replace the swirl control valve.

Click hereEngine / Hybrid System>2WW INTAKE / EXHAUST>INTAKE MANIFOLD>REMOVAL


b.

Perform the swirl valve learning value reset.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

21.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
16.REPAIR OR REPLACE EGR VALVE ASSEMBLY
a.

Repair or replace EGR valve assembly or perform inspections and troubleshooting for related DTCs.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>DIAGNOSTIC TROUBLE CODE CHART

HINT:

When the EGR valve assembly is replaced, perform initialization.



Result:
Proceed to
NEXT



NEXT

21.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
17.REPLACE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
a.

Replace the air cleaner filter element sub-assembly.


Result:
Proceed to
NEXT



NEXT

21.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
18.REPAIR OR REPLACE INTAKE SYSTEM
a.

Repair or replace the malfunctioning parts of the intake system.


Result:
Proceed to
NEXT



NEXT

21.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
19.REPAIR OR REPLACE HARNESS OR CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - EFI MAIN NO. 1 RELAY OR ECM POWER SOURCE CIRCUIT)
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

21.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
20.REPLACE INTAKE AIR TEMPERATURE SENSOR
a.

Replace the intake air temperature sensor.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>INTAKE AIR TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

21.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
21.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END