Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P1143  Inhibit Regeneration Detection  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1143 Inhibit Regeneration Detection Pressure difference of pressure sensors is higher than 0.06 bar (6 kPa).
(3 trip detection logic)
·

Open or short in differential pressure sensor circuit

·

Differential pressure sensor

·

Open or short in turbo pressure sensor assembly circuit

·

Turbo pressure sensor assembly

·

Open or short in exhaust gas pressure sensor circuit

·

Exhaust gas pressure sensor

·

ECM


Does not come on DTC stored

Related Data List
DTC No. Data List
P1143
·

MAP

·

Atmosphere Pressure

·

Sensed Value of the Pressure at TrbnUs

·

Filtered Pressure Value at Particle Filter Upstream



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

After replacing the Turbo Pressure Sensor assembly, the ECM needs initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

After replacing the Differential Pressure Sensor, the ECM needs initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION



HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / MAP, Atmosphere Pressure, Sensed Value of the Pressure at TrbnUs and Filtered Pressure Value at Particle Filter Upstream.

Powertrain > Engine and ECT > Data List
Tester Display
Atmosphere Pressure
MAP
Filtered Pressure Value at Particle Filter Upstream
Sensed Value of the Pressure at TrbnUs
50003 371 5,3,117,118

d.

Compare the values when the ignition switch is ON.

Standard:

Difference between the MAP, Atmosphere Pressure, Sensed Value of the Pressure at TrbnUs and Filtered Pressure Value at Particle Filter Upstream is less than 8 kPa.


HINT:

Standard atmospheric pressure is 101 kPa. For every 100 m increase in altitude, pressure drops by 1 kPa. Varies by weather.



Result:
Proceed to
OK
NG



OK

14.REPLACE ECM

NG

2.READ VALUE USING GTS (ATMOSPHERIC PRESSURE)
2.READ VALUE USING GTS (ATMOSPHERIC PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Atmosphere Pressure.

Powertrain > Engine and ECT > Data List
Tester Display
Atmosphere Pressure
50003 371 5
OK:

Atmosphere Pressure is the same as the actual atmospheric pressure.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (MAP)

NG

14.REPLACE ECM
3.READ VALUE USING GTS (MAP)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / MAP.

Powertrain > Engine and ECT > Data List
Tester Display
MAP
50003 371 3
OK:

MAP is the same as the actual atmospheric pressure.



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (FILTERED PRESSURE VALUE AT PARTICLE FILTER UPSTREAM)

NG

11.CHECK HARNESS AND CONNECTOR (TURBO PRESSURE SENSOR ASSEMBLY - ECM)
4.READ VALUE USING GTS (FILTERED PRESSURE VALUE AT PARTICLE FILTER UPSTREAM)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Filtered Pressure Value at Particle Filter Upstream.

Powertrain > Engine and ECT > Data List
Tester Display
Filtered Pressure Value at Particle Filter Upstream
50003 371 117
OK:

Filtered Pressure Value at Particle Filter Upstream is the same as the actual atmospheric pressure.



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (SENSED VALUE OF THE PRESSURE AT TRBNUS)

NG

9.CHECK HARNESS AND CONNECTOR (DIFFERENTIAL PRESSURE SENSOR - ECM)
5.READ VALUE USING GTS (SENSED VALUE OF THE PRESSURE AT TRBNUS)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Sensed Value of the Pressure at TrbnUs.

Powertrain > Engine and ECT > Data List
Tester Display
Sensed Value of the Pressure at TrbnUs
50003 371 118
OK:

Sensed Value of the Pressure at TrbnUs is the same as the actual atmospheric pressure.



Result:
Proceed to
OK
NG



OK

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P1143)

NG

7.CHECK HARNESS AND CONNECTOR (EXHAUST GAS PRESSURE SENSOR - ECM)
6.CHECK WHETHER DTC OUTPUT RECURS (DTC P1143)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Read the DTCs.

Result:
Result Proceed to
No DTC output A
DTC P1143 B




A

END

B

14.REPLACE ECM
7.CHECK HARNESS AND CONNECTOR (EXHAUST GAS PRESSURE SENSOR - ECM)
a.

Disconnect the exhaust gas pressure sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B130-1 (VC) - B112-24 (VCPE) Always Below 1 Ω
B130-2 (PEXM) - B112-103 (PEXM) Always Below 1 Ω
B130-3 (E2) - B112-135 (EPEM) Always Below 1 Ω
B130-1 (VC) or B112-24 (VCPE) - Body ground Always 10 kΩ or higher
B130-2 (PEXM) or B112-103 (PEXM) - Body ground Always 10 kΩ or higher
B130-3 (E2) or B112-135 (EPEM) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.REPLACE EXHAUST GAS PRESSURE SENSOR

NG

13.REPAIR OR REPLACE HARNESS OR CONNECTOR
8.REPLACE EXHAUST GAS PRESSURE SENSOR
a.

Result:
Proceed to
NEXT



NEXT

15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CHECK HARNESS AND CONNECTOR (DIFFERENTIAL PRESSURE SENSOR - ECM)
a.

Disconnect the differential pressure sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B127-1 (VC) - B112-70 (VCPX) Always Below 1 Ω
B127-2 (PEX) - B112-85 (PEX) Always Below 1 Ω
B127-3 (E2) - B112-71 (EPEX) Always Below 1 Ω
B127-1 (VC) or B112-70 (VCPX) - Body ground Always 10 kΩ or higher
B127-2 (PEX) or B112-85 (PEX) - Body ground Always 10 kΩ or higher
B127-3 (E2) or B112-71 (EPEX) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.REPLACE DIFFERENTIAL PRESSURE SENSOR

NG

13.REPAIR OR REPLACE HARNESS OR CONNECTOR
10.REPLACE DIFFERENTIAL PRESSURE SENSOR
a.

Replace the differential pressure sensor.

Click hereEngine / Hybrid System>2WW EMISSION CONTROL>DIFFERENTIAL PRESSURE SENSOR>REMOVAL


b.

Perform differential pressure learning value reset.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.CHECK HARNESS AND CONNECTOR (TURBO PRESSURE SENSOR ASSEMBLY - ECM)
a.

Disconnect the turbo pressure sensor assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B122-3 (PIM) - B112-111 (PIM) Always Below 1 Ω
B122-1 (VC) - B112-61 (VPIM) Always Below 1 Ω
B122-2 (E) - B112-76 (EPIM) Always Below 1 Ω
B122-3 (PIM) or B112-111 (PIM) - Body ground Always 10 kΩ or higher
B122-1 (VC) or B112-61 (VPIM) - Body ground Always 10 kΩ or higher
B122-2 (E) or B112-76 (EPIM) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

12.REPLACE TURBO PRESSURE SENSOR ASSEMBLY

NG

13.REPAIR OR REPLACE HARNESS OR CONNECTOR
12.REPLACE TURBO PRESSURE SENSOR ASSEMBLY
a.

Replace the turbo pressure sensor assembly.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>MANIFOLD ABSOLUTE PRESSURE SENSOR>REMOVAL


b.

Perform upstream turbine pressure learning value reset.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
13.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
14.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END