Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P200E  Catalyst System Over Temperature Bank 1  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P200E Catalyst System Over Temperature Bank 1 When exhaust gas temperature sensor (for sensor 1) value exceeds upper limit for 0.3 seconds.
(3 trip detection logic)
·

Open or short in exhaust gas temperature sensor (for sensor 1) circuit

·

Exhaust gas temperature sensor (for sensor 1)

·

Diesel throttle body

·

Swirl control valve

·

Turbocharger system

·

ECM


Does not come on DTC stored

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION


HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (ACTUATOR TEST OF THROTTLE VALVE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Actuator Test of Throttle Valve / Data List / Throttle Valve Actuator Position.

Powertrain > Engine and ECT > Active Test
Active Test Display
Actuator Test of Throttle Valve
Data List Display
Throttle Valve Actuator Position
50004 371 6 103

d.

Perform the following steps 1 to 4.


e.

Step 1

i.

Perform Active Test of throttle valve with control value of 5% (opening ratio in %).


ii.

Monitor the difference of the control value and Throttle Valve Actuator Position value (0 +/-3%).

Throttle valve must operate within 1 second.



f.

Step 2

i.

Wait for 2 seconds or more.



g.

Step 3

i.

Perform Active Test of throttle valve with control value of 91% (opening ratio in %).


ii.

Monitor the difference of the control value and Throttle Valve Actuator Position value (0 +/-3%).

Throttle valve must operate within 1 second.



h.

Step 4

i.

Wait for 2 seconds or more.



i.

Perform the above steps 1 to 4 and check that the part operates as specified.

OK:

Part operates as specified.



Result:
Proceed to
OK
NG



OK

2.PERFORM ACTIVE TEST USING GTS (ACTUATOR TEST OF SWIRL FLAP)

NG

12.REPLACE DIESEL THROTTLE BODY
2.PERFORM ACTIVE TEST USING GTS (ACTUATOR TEST OF SWIRL FLAP)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Actuator Test of Swirl Flap / Data List / Swirl Valve Actuator Position.

Powertrain > Engine and ECT > Active Test
Active Test Display
Actuator Test of Swirl Flap
Data List Display
Swirl Valve Actuator Position
50004 371 7 198
OK:

The value of "Swirl Valve Actuator Position" The value of "Swirl Valve Actuator Position" Swirl Flap" is operated, and the swirl flap operates smoothly.



Result:
Proceed to
OK
NG



OK

3.PERFORM ACTIVE TEST USING GTS (ACTUATOR TEST OF TURBO CHARGER)

NG

11.REPLACE SWIRL CONTROL VALVE
3.PERFORM ACTIVE TEST USING GTS (ACTUATOR TEST OF TURBO CHARGER)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Actuator Test of Turbo Charger.

Powertrain > Engine and ECT > Active Test
Tester Display
Actuator Test of Turbo Charger
50004 371 4

e.

Set the control value to 5%. The variable nozzle vane turbocharger must operate within 1 second. Valve travel when adjusted is approximately 15 mm.


f.

Wait for 2 seconds and set the control value to 95%. The variable nozzle vane turbocharger must operate within 1 second. Valve travel when adjusted is approximately 15 mm.


g.

Wait for 2 seconds and stop the operation using the variable nozzle vane turbocharger Active Test.

OK:

Operates smoothly when above procedure is performed.


HINT:

Check the movement of the variable turbine (stiffness, interference with other parts, etc.).



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (EXHAUST TEMPERATURE B1S1)

NG

10.REPLACE TURBOCHARGER SUB-ASSEMBLY
4.READ VALUE USING GTS (EXHAUST TEMPERATURE B1S1)
a.

Connect the GTS to the DLC3.


b.

Start the engine and warm it up.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Exhaust Temperature B1S1.

Powertrain > Engine and ECT > Data List
Tester Display
Exhaust Temperature B1S1
50003 371 58

e.

Read the value.

Standard:

Same as the actual exhaust gas temperature (50 to 700°C [122 to 1292°F] during idling after warm-up).


Result:
Result Proceed to
800°C (1472°F) A
Same as the actual exhaust gas temperature (50 to 700°C [122 to 1292°F] during idling after warm-up) B


HINT:
·

If there is an open circuit, the GTS indicates -40°C (-40°F).

·

If there is a short circuit, the GTS indicates 800°C (1472°F).





A

5.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

B

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
a.

Disconnect the exhaust gas temperature sensor (for sensor 1) connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Exhaust Temperature B1S1.

Powertrain > Engine and ECT > Data List
Tester Display
Exhaust Temperature B1S1
50003 371 58

e.

Read the value.

Standard value:

-40°C (-40°F)



Result:
Proceed to
OK
NG



OK

6.REPLACE EXHAUST GAS TEMPERATURE SENSOR (FOR SENSOR 1)

NG

7.CHECK HARNESS AND CONNECTOR (EXHAUST GAS TEMPERATURE SENSOR (FOR SENSOR 1) - ECM)
6.REPLACE EXHAUST GAS TEMPERATURE SENSOR (FOR SENSOR 1)
a.

Replace the exhaust gas temperature sensor (for sensor 1).

Click hereEngine / Hybrid System>2WW EMISSION CONTROL>EXHAUST GAS TEMPERATURE SENSOR(for Sensor 1)>REMOVAL


Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CHECK HARNESS AND CONNECTOR (EXHAUST GAS TEMPERATURE SENSOR (FOR SENSOR 1) - ECM)
a.

Disconnect the exhaust gas temperature sensor (for sensor 1) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B108-1 (THCI) or B112-92 (THCI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.REPLACE ECM

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
8.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.REPLACE TURBOCHARGER SUB-ASSEMBLY

Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.REPLACE SWIRL CONTROL VALVE
a.

Replace the swirl control valve.

Click hereEngine / Hybrid System>2WW INTAKE / EXHAUST>INTAKE MANIFOLD>REMOVAL


b.

Perform the swirl valve learning value reset.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.REPLACE DIESEL THROTTLE BODY
a.

Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END