Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P2196  O2 Sensor Signal Biased / Stuck Rich Bank 1 Sensor 1  


DESCRIPTION

Refer to DTC P0030.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>P0030

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2196 O2 Sensor Signal Biased / Stuck Rich Bank 1 Sensor 1 Oxygen concentration lower than estimated concentration for specified condition.
(3 trip detection logic)
·

Open or short in air fuel ratio sensor (for sensor 1) circuit

·

Air fuel ratio sensor (for sensor 1)

·

Fuel Injection system

·

EGR system

·

ECM


Does not come on DTC stored

Related Data List
DTC No. Data List
P2196
·

O2 Sensor Lambda Bank 1 Sensor 1

·

O2 Sensor Lambda Bank 1 Sensor 2



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the ECM and/or injector assembly, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

After replacing the air fuel ratio sensor, the ECM needs initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION



HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



Air fuel ratio sensors functional check


Refer to DTC P013A.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>P013A


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2196)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

d.

Read the DTCs.

Result:
Result Proceed to
DTC P2196 A
DTC P2196 and other DTCs B


HINT:
·

If any DTCs other than P2196 are output, troubleshoot those DTCs first.

·

In particular, if a DTC related to the fuel injection system, EGR system or air fuel ratio heater system is detected, perform diagnosis starting with that DTC.





A

2.PERFORM ACTIVE TEST USING GTS (FUEL BALANCING COMPENSATION (FBC))

B

2.PERFORM ACTIVE TEST USING GTS (FUEL BALANCING COMPENSATION (FBC))
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Fuel Balancing Compensation (FBC) / Data List / Cylinder 1 Quantity Compensation to Cylinder4 Quantity Compensation.

Powertrain > Engine and ECT > Active Test
Active Test Display
Fuel Balancing Compensation (FBC)
Data List Display
Cylinder 1 Quantity Compensation
Cylinder 2 Quantity Compensation
Cylinder 3 Quantity Compensation
Cylinder 4 Quantity Compensation
50004 371 16 110,111,112,113
OK:

-5.0 to 4.0 mg/stk


HINT:
·

If a malfunction is found during this inspection, the fuel injector may be stuck open.

·

If a malfunction is not found in the fuel injector, the probable cause may be a loss of compression pressure, the formation of soot deposits in the intake system or an excessively high or low injection volume.




Result:
Proceed to
OK
NG



OK

3.CHECK FOR EGR SYSTEM

NG

10.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
3.CHECK FOR EGR SYSTEM
a.

Check for exhaust gas leak from the EGR system.

OK:

No exhaust gas leak.



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR (FOR SENSOR 1) - ECM)

NG

9.REPAIR OR REPLACE EGR SYSTEM
4.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR (FOR SENSOR 1) - ECM)
a.

Disconnect the air fuel ratio sensor (for sensor 1) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B107-1 (AF1+) - B112-127 (AF1+) Always Below 1 Ω
B107-2 (AF1-) - B112-126 (AF1-) Always Below 1 Ω
B107-3 (HAF1) - B112-46 (HAF1) Always Below 1 Ω
B107-5 (TR1) - B112-128 (TR1) Always Below 1 Ω
B107-6 (RE1) - B112-125 (RE1) Always Below 1 Ω
B107-1 (AF1+) or B112-127 (AF1+) - Body ground Always 10 kΩ or higher
B107-2 (AF1-) or B112-126 (AF1-) - Body ground Always 10 kΩ or higher
B107-3 (HAF1) or B112-46 (HAF1) - Body ground Always 10 kΩ or higher
B107-5 (TR1) or B112-128 (TR1) - Body ground Always 10 kΩ or higher
B107-6 (RE1) or B112-125 (RE1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE AIR FUEL RATIO SENSOR (FOR SENSOR 1)

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.REPLACE AIR FUEL RATIO SENSOR (FOR SENSOR 1)
a.

Replace the air fuel ratio sensor (for sensor 1).

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>AIR FUEL RATIO SENSOR(for Sensor 1)>REMOVAL


b.

Perform the O2 sensor learning value reset.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P2196)
6.CHECK WHETHER DTC OUTPUT RECURS (DTC P2196)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Read the DTCs.

Result:
Result Proceed to
No DTC output A
DTC P2196 B




A

END

B

7.REPLACE ECM
7.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.REPAIR OR REPLACE EGR SYSTEM
a.

Repair or replace the EGR system.


Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
a.

Replace the injector assembly of the malfunctioning cylinder.

Click hereEngine / Hybrid System>2AR-FE FUEL>FUEL INJECTOR>REMOVAL


b.

Register the injector compensation code.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>REGISTRATION


Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END