The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during instrument panel passenger airbag assembly removal/installation are shown below.
After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.
After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
1. PRECAUTION
Be sure to read precaution thoroughly before servicing.
w/o Occupant Classification System:
for Gasoline Model with Occupant Classification System:
for HV Model with Occupant Classification System:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
58410B
2.REMOVE DECK BOARD ASSEMBLY (for HV Model)
58416K
3.REMOVE REAR NO. 2 FLOOR BOARD (for HV Model)
65351A
4.REMOVE BATTERY HOLE COVER (for HV Model)
5.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
for A25A-FKS:
for M20A-FKS:
for A25A-FXS:
Click hereGeneral>MAINTENANCE>A25A-FXS AUXILIARY BATTERY>REMOVAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
6.REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY
55950G
7.REMOVE DEFROSTER NOZZLE ASSEMBLY
55086
8.REMOVE NO. 3 HEATER TO REGISTER DUCT SUB-ASSEMBLY
55972C
9.REMOVE NO. 2 SIDE DEFROSTER NOZZLE DUCT
82142A
10.REMOVE NO. 2 INSTRUMENT PANEL WIRE
for Dual Type:
| *a | Lock Button |
| *b | Wire Harness Clamp |
| *c | Guide |
|
Protective Tape |
|
Release in this Direction |
Using a screwdriver, release the lock button and disconnect the 2 airbag connectors.
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
Tape the screwdriver tip before use.
Detach the wire harness clamp and guide and remove the No. 2 instrument panel wire.
for Single Type:
| *a | Lock Button |
| *b | Wire Harness Clamp |
| *c | Guide |
|
Protective Tape |
|
Release in this Direction |
Using a screwdriver, release the lock button and disconnect the airbag connector.
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
Tape the screwdriver tip before use.
Detach the wire harness clamp and guide and remove the No. 2 instrument panel wire.
73960A
11.REMOVE INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY
|
Deployment Side |
When storing the instrument panel passenger airbag assembly, keep the airbag deployment side facing upward.
If the airbag deploys for any reason, it may cause a serious accident.
Remove the 2 screws.
Insert moulding remover B into the side of the airbag door facing the front of the vehicle and detach the hook.
|
Hold Here |
|
Move in this Direction |
While holding the positions shown in the illustration, move the instrument panel passenger airbag assembly toward you, detach the hook near the rear of the vehicle, and then remove the instrument panel passenger airbag assembly.