The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the air conditioning unit assembly removal/installation are shown below.
Wear protective gloves. Sharp areas on the parts may injure your hands.
There is risk of injury.
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Use the same procedure as for the LHD and RHD vehicles.
The procedure listed below is for the LHD vehicles.
1. PRECAUTION
Make sure to select face mode before disconnecting the cable from the negative (-) battery terminal.
2. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
3.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
for HFC-134a (R134a):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFC-134a(R134a))>REPLACEMENT
for HFO-1234yf (R1234yf):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFO-1234yf(R1234yf))>REPLACEMENT
4.DRAIN ENGINE COOLANT
5.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
55752
6.REMOVE COWL VENTILATOR SPLASH SHIELD
Remove using the same procedure that is performed when replacement of the cowl ventilator splash shield is necessary.
Click hereVehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>REMOVAL
55704B
7.REMOVE COWL VENTILATOR PANEL SUB-ASSEMBLY
8.REMOVE HOLE PLUG
88707
9.DISCONNECT SUCTION PIPE SUB-ASSEMBLY (w/o Sub-cool Accelerator)
Remove the bolt.
|
Rotate in this Direction |
Rotate the 1-point tightening plate as shown in the illustration.
Disconnect the suction pipe sub-assembly.
Do not apply excessive force to the suction pipe sub-assembly.
Remove the O-ring from the suction pipe sub-assembly.
Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.
88710E
10.DISCONNECT AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY (w/o Sub-cool Accelerator)
Disconnect the air conditioning tube and accessory assembly.
Do not apply excessive force to the air conditioning tube and accessory assembly.
Remove the O-ring from the air conditioning tube and accessory assembly.
Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.
88710G
11.DISCONNECT NO. 2 AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY (w/ Sub-cool Accelerator)
Remove the bolt.
|
Rotate in this Direction |
Rotate the 1-point tightening plate as shown in the illustration.
Disconnect the No. 2 air conditioning tube and accessory assembly.
Do not apply excessive force to the No. 2 air conditioning tube and accessory assembly.
Remove the 2 O-rings from the No. 2 air conditioning tube and accessory assembly.
Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.
87246
12.DISCONNECT OUTLET HEATER WATER HOSE
Using pliers, grip the claws of the clip and slide the clip to disconnect the outlet heater water hose.
Do not apply excessive force to the outlet heater water hose.
Prepare a drain pan or cloth in case the coolant leaks.
87245
13.DISCONNECT INLET HEATER WATER HOSE
Using pliers, grip the claws of the clip and slide the clip to disconnect the inlet heater water hose.
Do not apply excessive force to the inlet heater water hose.
Prepare a drain pan or cloth in case the coolant leaks.
87128
14.REMOVE HEATER GROMMET
15.REMOVE FRONT SEAT ASSEMBLY LH
for Manual Seat:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>REMOVAL
for Power Seat:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>REMOVAL
16.REMOVE FRONT SEAT ASSEMBLY RH
Use the same procedure as for the LH side.
17.REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY
45250
18.REMOVE STEERING COLUMN ASSEMBLY (except Manual Transaxle RHD)
87211
19.REMOVE NO. 1 AIR DUCT (for Manual Transaxle RHD)
45250
20.LOOSEN STEERING COLUMN ASSEMBLY (for Manual Transaxle RHD)
Loosen the 2 bolts and 2 nuts.
| *A | for Type A | *B | for Type B |
|
Bolt |
|
Nut |
21.REMOVE NAVIGATION ECU WITH BRACKET (w/ Navigation System)
22.REMOVE TELEPHONE TRANSCEIVER ASSEMBLY WITH BRACKET (w/ Telematics Transceiver)
for LHD:
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL
for RHD:
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL
23.REMOVE NAVIGATION ECU WITH BRACKET (w/ Dummy Case)
Use the same procedure described as for the navigation ECU with bracket or telephone transceiver assembly with bracket.
73233
24.REMOVE OUTER LAP BELT ANCHOR COVER
67918E
25.REMOVE REAR DOOR SCUFF PLATE LH
73220
26.REMOVE FRONT SEAT OUTER BELT ASSEMBLY LH
62414A
27.REMOVE LOWER CENTER PILLAR GARNISH LH
Remove the rear side of the front door opening trim weatherstrip LH so that the lower center pillar garnish LH can be removed.
Click hereVehicle Exterior>DOOR / HATCH>FRONT DOOR OPENING TRIM WEATHERSTRIP>REMOVAL
Remove the front side of the rear door opening trim weatherstrip LH so that the lower center pillar garnish LH can be removed.
Click hereVehicle Exterior>DOOR / HATCH>REAR DOOR OPENING TRIM WEATHERSTRIP>REMOVAL
Remove the lower center pillar garnish LH.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL
67917C
28.REMOVE REAR DOOR SCUFF PLATE RH
Use the same procedure described as for the rear door scuff plate LH.
73210
29.REMOVE FRONT SEAT OUTER BELT ASSEMBLY RH
Use the same procedure described as for the front seat outer belt assembly LH.
62413A
30.REMOVE LOWER CENTER PILLAR GARNISH RH
Use the same procedure described as for the lower center pillar garnish LH.
78118
31.REMOVE ACCELERATOR PEDAL PAD
78010F
32.REMOVE ACCELERATOR PEDAL ASSEMBLY
58569D
33.REMOVE FRONT FLOOR CAUTION PLATE COVER
58510C
34.REMOVE FRONT FLOOR FRONT CARPET ASSEMBLY
55215D
35.REMOVE NO. 3 DASH PANEL INSULATOR PAD
87212H
36.REMOVE REAR NO. 4 AIR DUCT
87212G
37.REMOVE REAR NO. 3 AIR DUCT
87212F
38.REMOVE REAR NO. 2 AIR DUCT
Use the same procedure as for the rear No. 4 air duct.
87212
39.REMOVE REAR NO. 1 AIR DUCT
Use the same procedure as for the rear No. 3 air duct.
58861B
40.REMOVE NO. 1 CONSOLE BOX DUCT
| *A | for CVT |
| *B | for Manual Transaxle |
Detach the clamp.
Remove the clip and No. 1 console box duct.
55085
41.REMOVE NO. 2 HEATER TO REGISTER DUCT SUB-ASSEMBLY
55308B
42.REMOVE NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY
for CVT LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for Manual Transaxle LHD:
| *a | Clamp |
| *b | Guide |
|
Bolt |
|
Nut |
Detach the clamp and guide.
Remove the bolt, nut and No. 3 instrument panel to cowl brace sub-assembly.
for RHD:
Click herePower Source / Network>NETWORKING>NETWORK GATEWAY ECU (for RHD)>REMOVAL
43.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU (for CVT LHD)
82877
44.REMOVE ECU INTEGRATION BOX RH (for RHD)
45.DISCONNECT INSTRUMENT PANEL WIRE
for LHD:
| *a | Clamp |
| *b | Guide |
Disconnect the 2 connectors.
Detach the clamp and guide.
for CVT LHD:
Remove the 3 bolts.
| *a | Clamp | *b | Guide |
Detach the guide and disconnect the 3 ground wires.
Detach the clamp.
Remove the nut.
| *A | for Automatic Air Conditioning System | - | - |
| *a | Clamp | *b | Guide |
|
Bolt |
|
Nut |
|
Connector |
|
Lever Connector |
Remove the bolt.
Detach the guide and disconnect the ground wire.
Disconnect the connector.
Detach the clamp.
Disconnect the lever connector.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>REMOVAL
for Manual Transaxle LHD:
Remove the nut.
| *a | Clamp | *b | Guide |
|
Bolt |
|
Nut |
Remove the 3 bolts.
Detach the guide and disconnect the 3 ground wires.
Detach the clamp.
Remove the nut.
| *A | for Automatic Air Conditioning System | - | - |
| *a | Clamp | *b | Guide |
|
Bolt |
|
Nut |
|
Connector |
|
Lever Connector |
Remove the bolt.
Detach the guide and disconnect the ground wire.
Disconnect the connector.
Detach the clamp.
Disconnect the lever connector.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>REMOVAL
for RHD:
Remove the 2 bolts.
| *a | Clamp | *b | Guide |
Detach the guide and disconnect the 2 ground wires.
Detach the clamp.
Remove the nut.
| *A | for Automatic Air Conditioning System | - | - |
| *a | Clamp | *b | Guide |
|
Bolt |
|
Nut |
|
Connector |
|
Lever Connector |
Remove the 2 bolts.
Detach the guide and disconnect the 2 ground wires.
Disconnect the connector.
Detach the clamp.
Disconnect the lever connector.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>REMOVAL
8598A
46.REMOVE DOOR CONTROL BATTERY (w/ Door Control Battery)
for LHD:
Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL BATTERY (for LHD)>REMOVAL
for RHD:
Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL BATTERY (for RHD)>REMOVAL
47.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU (for Manual Transaxle LHD)
82877
48.REMOVE ECU INTEGRATION BOX RH (for LHD)
for CVT:
Click herePower Source / Network>NETWORKING>NETWORK GATEWAY ECU (for LHD)>REMOVAL
for Manual Transaxle:
Click herePower Source / Network>NETWORKING>NETWORK GATEWAY ECU (for LHD)>REMOVAL
89261A
49.REMOVE ENGINE STOP AND START ECU (for RHD with Stop and Start System)
50.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU (for RHD)
51.DISCONNECT INSTRUMENT PANEL WIRE
for CVT LHD:
Remove the 2 bolts.
| *a | Clamp | *b | Guide |
|
Bolt |
|
Connector |
Detach the guide and disconnect the 2 ground wires.
Disconnect the connector.
Detach the clamp.
for Manual Transaxle LHD:
Remove the 2 bolts.
| *a | Clamp | *b | Guide |
|
Bolt |
|
Connector |
Detach the guide and disconnect the 2 ground wires.
Disconnect the connector.
Detach the clamp.
for RHD:
| *a | Clamp |
| *b | Guide |
Disconnect the 2 connectors.
Detach the clamp and guide.
Remove the 2 bolts.
| *a | Clamp | *b | Guide |
|
Bolt |
|
Connector |
Detach the guide and disconnect the 2 ground wires.
Disconnect the connector.
Detach the clamp.
55306A
52.REMOVE NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY
55307C
53.REMOVE NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY
88539J
54.DISCONNECT DRAIN COOLER HOSE
55.REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONING UNIT ASSEMBLY
Be sure to support the air conditioning unit assembly when removing it because failure to do so may cause the bracket of the air conditioning unit assembly to break.
When disassembling the air conditioning unit assembly, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.
Be careful not to damage the internal components of the instrument panel reinforcement assembly with air conditioning unit assembly on the glass etc. Only perform removal after first taking the appropriate actions.
Do not allow the instrument panel reinforcement assembly with air conditioning unit assembly to strike the airbag ECU assembly. Doing so may damage the heater case, causing water leaks.
|
Bolt (A) |
Remove the 3 bolts (A).
Remove the bolt (B).
|
Bolt (B) |
|
Bolt (C) |
|
Nut | - | - |
for Manual Transaxle LHD:
|
Bolt (D) |
Remove the bolt (D).
Remove the nut.
Remove the 4 bolts (C).
Remove the instrument panel reinforcement assembly with air conditioning unit assembly from the guide as shown in the illustration.
Do not hold the air conditioning harness assembly. Otherwise, static electricity from the technician may damage the air conditioning harness assembly.
Do not hold the heater core or pipe of the heater radiator unit sub-assembly. Otherwise, the pipe may detach, the clamp may be damaged, or the crimped areas of the heater core and pipe of the heater radiator unit sub-assembly may be damaged, causing coolant to leak.
Do not hold the air conditioning radiator damper servo sub-assembly, blower damper servo sub-assembly or link. Otherwise, the servo motor may become misaligned, causing abnormal operation noise, temperature control defects, or air leaks due to sealing defects in the doors.
Do not hold the door. Doing so may cause air leaks due to closing defects resulting from excessive opening/closing. Also, keep the door free from oil and grease.
|
Remove in this Direction | - | - |
45220
56.DISCONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY (for Manual Transaxle RHD)
| *a | Matchmark |
|
Disconnect in this Direction |
Remove the bolt and slide the steering intermediate shaft assembly.
Do not remove the steering intermediate shaft assembly from the steering column assembly.
Put matchmarks on the steering intermediate shaft assembly and steering column assembly.
Disconnect the steering intermediate shaft assembly from the steering column assembly.
45250
57.REMOVE STEERING COLUMN ASSEMBLY (for Manual Transaxle RHD)
88650N
58.REMOVE AIR CONDITIONING AMPLIFIER ASSEMBLY
59.DISCONNECT INSTRUMENT PANEL WIRE
60.REMOVE AIR CONDITIONING UNIT ASSEMBLY
87201
61.REMOVE NO. 1 AIR DUCT SUB-ASSEMBLY
58511K
62.REMOVE NO. 1 FLOOR MAT (for RHD)
88539G
63.REMOVE COOLER UNIT DRAIN HOSE GROMMET