Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER (for RHD with Vacuum Brake Booster) › 2018.10–2020.08
RM3620E _54 Brake _076411 BRAKE SYSTEM (OTHER) _0377039 BRAKE BOOSTER(for RHD with Vacuum Brake Booster) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER(for RHD with Vacuum Brake Booster)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during brake booster assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Battery terminal is disconnected/reconnected Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system for A25A-FKS:
(Click here)
for M20A-FKS:
(Click here)
Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)
Reset back door close position Power back door system (for Gasoline model) (Click here)
Power back door initialization Power door lock control system (Click here)

NOTICE:
·

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.

·

Make sure to release vacuum from the brake booster assembly before removing the brake master cylinder sub-assembly from the brake booster assembly.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.


Hide 2.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 3.DRAIN ENGINE COOLANT

Hide 47201 4.REMOVE BRAKE MASTER CYLINDER SUB-ASSEMBLY

Hide 73900 5.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

Hide 87211A 6.REMOVE NO. 2 AIR DUCT

Hide 84340 7.REMOVE STOP LIGHT SWITCH ASSEMBLY

Hide 47101A 8.REMOVE BRAKE PEDAL RETURN SPRING

Hide 9.SEPARATE WIRE HARNESS

a.
C406470

Disconnect the connector.


b.

Disengage the 2 clamps to separate the wire harness from the brake pedal support assembly.


Hide 10.LOOSEN LOCK NUT

a.
C407862C01
1.271,1.813 1.365,1.813 1.365,1.813 1.927,1.146 true 2.74,1.802 2.615,1.802 2.615,1.802 2.156,1.219 true 1.063,1.708 1.281,1.896 0.219,0.188 10 true *1 2.792,1.729 2.979,1.906 0.188,0.177 10 true *2
*1 Lock Nut
*2 Brake Master Cylinder Push Rod Clevis


Loosen the lock nut of the brake master cylinder push rod clevis.


Hide 44772 12.DISCONNECT CHECK VALVE TO CONNECTOR TUBE HOSE

a.
C407852

Slide the clip and disconnect the check valve to connector tube hose from the brake booster assembly.


Hide 44763A 13.DISCONNECT NO. 1 HOSE TO HOSE TUBE

a.
C407857

Remove the 2 nuts to disconnect the No. 1 hose to hose tube from the vehicle body.


Hide 88707 14.DISCONNECT SUCTION PIPE SUB-ASSEMBLY (w/o Sub-cool Accelerator)

Hide 88710E 15.DISCONNECT AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY (w/o Sub-cool Accelerator)

Hide 88710G 16.DISCONNECT NO. 2 AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY (w/ Sub-cool Accelerator)

Hide 47313 17.DISCONNECT FRONT NO. 3 BRAKE TUBE

a.
C407877

Disengage the clamp to disconnect the front No. 3 brake tube from the brake tube clamp.


b.
C407880

Disengage the clamp and remove the brake tube clamp.


c.
C407878

Using a union nut wrench, disconnect the front No. 3 brake tube from the front brake flexible hose.

NOTICE:
·

Do not damage or deform the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.




Hide 88707 18.SEPARATE SUCTION PIPE SUB-ASSEMBLY

a.
C407855

Disengage the 2 clamps to separate the suction pipe sub-assembly from the vehicle body.


Hide 44610 19.REMOVE BRAKE BOOSTER ASSEMBLY

a.
C407853

Disconnect the connector from the vacuum warning switch assembly.


b.
C407854

w/ Stop and Start System:

i.

Disconnect the connector from the vacuum sensor assembly.



c.
C407858

Disengage the 5 clamps to remove the brake tube clamp from the brake lines.


d.
C407859C01
0.354,0.219 0.667,0.375 0.313,0.156 10 false *a 1.74,0.24 2.052,0.396 0.313,0.156 10 false *b
*a except Manual Transaxle
*b for Manual Transaxle


Remove the brake tube clamp.

i.

for Manual Transaxle:

Disengage the 6 clamps to remove the brake tube clamp from the brake lines.


ii.

except Manual Transaxle:

Disengage the 5 clamps to remove the brake tube clamp from the brake lines.



e.
C407860C01
0.354,0.219 0.667,0.375 0.313,0.156 10 false *a 1.74,0.24 2.052,0.396 0.313,0.156 10 false *b
*a except Manual Transaxle
*b for Manual Transaxle


Disconnect the brake lines.

i.

for Manual Transaxle:

Disengage the 4 clamps to remove the brake tube clamp from the brake lines.


ii.

except Manual Transaxle:

Disengage the 3 clamps to remove the brake tube clamp from the brake lines.



f.
C407861

Remove the bolt and brake tube clamp from the vehicle body.


g.

Disengage the clamp to remove the brake tube clamp from the vehicle body.


h.
C407856C01
1.188,1.938 1.354,1.938 1.354,1.938 1.656,1.479 true 1.969,1.302 2.385,1.833 2.385,1.833 2.552,1.833 true 2.594,1.74 2.802,1.948 0.208,0.208 10 true *a 1,1.844 1.208,2.052 0.208,0.208 10 true *b
*a From 1st Chamber of Brake Master Cylinder Sub-assembly
*b From 2nd Chamber of Brake Master Cylinder Sub-assembly


Using a union nut wrench, remove the 2 brake lines from the brake actuator assembly.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.




i.
C407863

Remove the 4 nuts.


j.

Remove the brake master cylinder push rod clevis and lock nut from the brake booster assembly.


k.

Remove the brake booster assembly from the vehicle body.

NOTICE:
·

Do not apply excessive force to the brake lines or refrigerant lines.

·

Do not apply excessive force to the suction pipe sub-assembly.




Hide 44785 20.REMOVE BRAKE BOOSTER GASKET

a.

Remove the brake booster gasket from the brake booster assembly.