Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT (for A25A-FKS) › 2018.10–2020.08
RM3620E _58 Vehicle Interior _076130 HEATING / AIR CONDITIONING _0374934 AIR CONDITIONING UNIT(for A25A-FKS) A

HEATING / AIR CONDITIONING  AIR CONDITIONING UNIT(for A25A-FKS)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the air conditioning unit assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Battery terminal is disconnected/reconnected Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system (Click here)
Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)
Reset back door close position Power back door system (for Gasoline model) (Click here)
Power back door initialization Power door lock control system (Click here)
Steering sensor (Including removal and installation) Steering angle setting Parking assist monitor system (Click here)
Adjust steering angle Panoramic view monitor system (for Gasoline model) (Click here)
Steering angle neutral point Parking assist monitor system (Click here)
Parking support brake system (for Gasoline model) (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)

CAUTION:
B521791

·

Wear protective gloves. Sharp areas on the parts may injure your hands.

·

There is risk of injury.



CAUTION:
B475753

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.



NOTICE:
·

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



HINT:
·

Use the same procedure as for the LHD and RHD vehicles.

·

The procedure listed below is for the LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

Make sure to select face mode before disconnecting the cable from the negative (-) battery terminal.


Hide 2. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 3.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 4.DRAIN ENGINE COOLANT

Hide 5.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 55752 6.REMOVE COWL VENTILATOR SPLASH SHIELD

HINT:

Remove using the same procedure that is performed when replacement of the cowl ventilator splash shield is necessary.

Click hereVehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>REMOVAL


Hide 55704B 7.REMOVE COWL VENTILATOR PANEL SUB-ASSEMBLY

Hide 88707 9.DISCONNECT SUCTION PIPE SUB-ASSEMBLY (w/o Sub-cool Accelerator)

a.
E408005

Remove the bolt.


b.
E408006C01
0,0 0,0 false
V113147

Rotate in this Direction


Rotate the 1-point tightening plate as shown in the illustration.


c.
E408007

Disconnect the suction pipe sub-assembly.

NOTICE:

Do not apply excessive force to the suction pipe sub-assembly.



d.

Remove the O-ring from the suction pipe sub-assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



Hide 88710E 10.DISCONNECT AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY (w/o Sub-cool Accelerator)

a.
E408008

Disconnect the air conditioning tube and accessory assembly.

NOTICE:

Do not apply excessive force to the air conditioning tube and accessory assembly.



b.

Remove the O-ring from the air conditioning tube and accessory assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



Hide 88710G 11.DISCONNECT NO. 2 AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY (w/ Sub-cool Accelerator)

a.
E408009

Remove the bolt.


b.
E408010C01
0,0 0,0 false
V113147

Rotate in this Direction


Rotate the 1-point tightening plate as shown in the illustration.


c.
E408011

Disconnect the No. 2 air conditioning tube and accessory assembly.

NOTICE:

Do not apply excessive force to the No. 2 air conditioning tube and accessory assembly.



d.

Remove the 2 O-rings from the No. 2 air conditioning tube and accessory assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



Hide 87246 12.DISCONNECT OUTLET HEATER WATER HOSE

a.
E408012

Using pliers, grip the claws of the clip and slide the clip to disconnect the outlet heater water hose.

NOTICE:
·

Do not apply excessive force to the outlet heater water hose.

·

Prepare a drain pan or cloth in case the coolant leaks.




Hide 87245 13.DISCONNECT INLET HEATER WATER HOSE

a.
E408013

Using pliers, grip the claws of the clip and slide the clip to disconnect the inlet heater water hose.

NOTICE:
·

Do not apply excessive force to the inlet heater water hose.

·

Prepare a drain pan or cloth in case the coolant leaks.




Hide 15.REMOVE FRONT SEAT ASSEMBLY LH

Hide 16.REMOVE FRONT SEAT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 17.REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY

Hide 45250 18.REMOVE STEERING COLUMN ASSEMBLY

Hide 19.REMOVE NAVIGATION ECU WITH BRACKET (w/ Navigation System)

Hide 20.REMOVE TELEPHONE TRANSCEIVER ASSEMBLY WITH BRACKET (w/ Telematics Transceiver)

Hide 21.REMOVE NAVIGATION ECU WITH BRACKET (w/ Dummy Case)

HINT:

Use the same procedure described as for the navigation ECU with bracket or telephone transceiver assembly with bracket.


Hide 73233 22.REMOVE OUTER LAP BELT ANCHOR COVER

Hide 67918E 23.REMOVE REAR DOOR SCUFF PLATE LH

Hide 73220 24.REMOVE FRONT SEAT OUTER BELT ASSEMBLY LH

Hide 62414A 25.REMOVE LOWER CENTER PILLAR GARNISH LH

a.

Remove the rear side of the front door opening trim weatherstrip LH so that the lower center pillar garnish LH can be removed.

Click hereVehicle Exterior>DOOR / HATCH>FRONT DOOR OPENING TRIM WEATHERSTRIP>REMOVAL


b.

Remove the front side of the rear door opening trim weatherstrip LH so that the lower center pillar garnish LH can be removed.

Click hereVehicle Exterior>DOOR / HATCH>REAR DOOR OPENING TRIM WEATHERSTRIP>REMOVAL


c.

Remove the lower center pillar garnish LH.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 67917C 26.REMOVE REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure described as for the rear door scuff plate LH.


Hide 73210 27.REMOVE FRONT SEAT OUTER BELT ASSEMBLY RH

HINT:

Use the same procedure described as for the front seat outer belt assembly LH.


Hide 62413A 28.REMOVE LOWER CENTER PILLAR GARNISH RH

HINT:

Use the same procedure described as for the lower center pillar garnish LH.


Hide 78118 29.REMOVE ACCELERATOR PEDAL PAD

Hide 78010F 30.REMOVE ACCELERATOR PEDAL ASSEMBLY

Hide 58569D 31.REMOVE FRONT FLOOR CAUTION PLATE COVER

Hide 58510C 32.REMOVE FRONT FLOOR FRONT CARPET ASSEMBLY

Hide 55215D 33.REMOVE NO. 3 DASH PANEL INSULATOR PAD

Hide 87212F 36.REMOVE REAR NO. 2 AIR DUCT

HINT:

Use the same procedure described as for the rear No. 4 air duct.


Hide 87212 37.REMOVE REAR NO. 1 AIR DUCT

HINT:

Use the same procedure described as for the rear No. 3 air duct.


Hide 55085 39.REMOVE NO. 2 HEATER TO REGISTER DUCT SUB-ASSEMBLY

Hide 55308B 40.REMOVE NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY

Hide 41.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU (for LHD)

Hide 82877 42.REMOVE ECU INTEGRATION BOX RH (for RHD)

Hide 43.DISCONNECT INSTRUMENT PANEL WIRE

a.

for LHD:

i.
E408014C01
1.531,1.281 1.698,1.469 0.167,0.188 10 true *a 2.177,1.063 2.344,1.25 0.167,0.188 10 true *b
*a Clamp
*b Guide


Disconnect the 2 connectors.


ii.

Detach the clamp and guide.


iii.

Remove the 3 bolts.

E408015C01
2.156,3.469 2.49,3.469 true 2.302,3.625 2.635,3.625 true 2.375,4.948 2.552,5.135 0.177,0.188 10 true *a 2.365,1.646 2.542,1.833 0.177,0.188 10 true *a 1.969,3.375 2.146,3.563 0.177,0.188 10 true *a 3,2.531 3.177,2.719 0.177,0.188 10 true *a 3.458,2.75 3.635,2.938 0.177,0.188 10 true *a 4.698,1.073 4.875,1.26 0.177,0.188 10 true *a 2.115,4.854 2.292,5.042 0.177,0.188 10 true *b 2.135,3.531 2.313,3.719 0.177,0.188 10 true *b 5.167,4.333 5.344,4.521 0.177,0.188 10 true *b
*a Clamp *b Guide



iv.

Detach the guide and disconnect the 3 ground wires.


v.

Detach the clamp.


vi.

Remove the nut.

E408016C01
1,1.5 1.188,1.698 0.188,0.198 10 true *a 3.427,1.719 3.615,1.917 0.188,0.198 10 true *a 3.615,2.708 3.802,2.906 0.188,0.198 10 true *a 3.052,4.281 3.24,4.479 0.188,0.198 10 true *a 4.271,3.354 4.458,3.552 0.188,0.198 10 true *a 3.802,2.167 3.99,2.365 0.188,0.198 10 true *b 4.271,4.333 4.458,4.531 0.188,0.198 10 true *a 4.063,4.031 4.281,4.229 0.219,0.198 12 true *A 4.333,4.938 4.521,5.135 0.188,0.198 10 true *a 0.552,2.604 0.771,2.802 0.219,0.198 12 true *C 2.844,4.031 3.063,4.229 0.219,0.198 12 true *B
*A for Type A *B for Type B
*C for Automatic Air Conditioning System - -
*a Clamp *b Guide
V100135

Bolt
V100136

Nut
V100137

Connector
V100138

Lever Connector



vii.

Remove the bolt.


viii.

Detach the guide and disconnect the ground wire.


ix.

Disconnect the connector.


x.

Detach the clamp.




b.

for RHD:

i.

Remove the 2 bolts.

E408017C01
4.656,2.115 4.99,2.115 true 1.344,2.521 1.521,2.708 0.177,0.188 10 true *a 4.792,1.646 4.969,1.833 0.177,0.188 10 true *a 5.094,0.594 5.271,0.781 0.177,0.188 10 true *a 4.99,2.031 5.167,2.219 0.177,0.188 10 true *a 3.281,2.875 3.458,3.063 0.177,0.188 10 true *a 6.271,4.594 6.448,4.781 0.177,0.188 10 true *a 2.979,2.573 3.156,2.76 0.177,0.188 10 true *b 5.188,2.677 5.365,2.865 0.177,0.188 10 true *b
*a Clamp *b Guide



ii.

Detach the guide and disconnect the 2 ground wires.


iii.

Detach the clamp.


iv.

Remove the nut.

E408018C01
5.021,4.51 5.25,4.708 0.229,0.198 12 true *A 4.146,5.365 4.323,5.542 0.177,0.177 10 true *a 4.26,4.719 4.438,4.896 0.177,0.177 10 true *a 4.313,3.833 4.49,4.01 0.177,0.177 10 true *a 4.906,3.292 5.083,3.469 0.177,0.177 10 true *a 5.219,2.198 5.396,2.375 0.177,0.177 10 true *a 2.875,1.542 3.052,1.719 0.177,0.177 10 true *a 1.25,0.479 1.427,0.656 0.177,0.177 10 true *a 0.813,0.698 0.99,0.875 0.177,0.177 10 true *a 2.781,3.99 2.958,4.167 0.177,0.177 10 true *a 1,5.156 1.177,5.333 0.177,0.177 10 true *a 4.729,2.75 4.906,2.927 0.177,0.177 10 true *b 3.979,1.521 4.156,1.698 0.177,0.177 10 true *b
*A for Automatic Air Conditioning System - -
*a Clamp *b Guide
V100135

Bolt
V100136

Nut
V100137

Connector
V100138

Lever Connector



v.

Remove the 2 bolts.


vi.

Detach the guide and disconnect the 2 ground wires.


vii.

Disconnect the connector.


viii.

Detach the clamp.




Hide 8598A 44.REMOVE DOOR CONTROL BATTERY (w/ Door Control Battery)

Hide 82877 45.REMOVE ECU INTEGRATION BOX RH (for LHD)

Hide 89261A 46.REMOVE ENGINE STOP AND START ECU (for RHD with Stop and Start System)

Hide 47.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU (for RHD)

Hide 55306A 49.REMOVE NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

Hide 55307C 50.REMOVE NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

Hide 52.REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONING UNIT ASSEMBLY

Hide 88650N 53.REMOVE AIR CONDITIONING AMPLIFIER ASSEMBLY

Hide 54.DISCONNECT INSTRUMENT PANEL WIRE

a.

for LHD:

i.

Disconnect the connector.

E408066C01
6,0.385 6.24,0.604 0.24,0.219 12 true *A
*A w/ ECU - -



ii.

Detach the clamp.



b.

for RHD:

i.

Disconnect the connector.

E408068


ii.

Detach the clamp.



Hide 88539G 58.REMOVE COOLER UNIT DRAIN HOSE GROMMET