Home › Vehicle Exterior › DOOR / HATCH › FUEL LID LOCK CONTROL CABLE ASSEMBLY (for LHD) › 2018.10–2020.08
RM3620E _59 Vehicle Exterior _076335 DOOR / HATCH _0377477 FUEL LID LOCK CONTROL CABLE ASSEMBLY(for LHD) A

DOOR / HATCH  FUEL LID LOCK CONTROL CABLE ASSEMBLY(for LHD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the fuel lid lock control cable assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Removal and installation of auxiliary battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system for A25A-FKS:(Click here)
for M20A-FKS:(Click here)
Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)
Reset back door close position Power back door system (for Gasoline model) (Click here)
Power back door initialization Power door lock control system (Click here)
·

Position control ECU assembly (driver seat) (Including removal and installation)

·

Reclining motor (Front seatback frame sub-assembly (driver seat)) (Including removal and installation)

·

Slide motor (Front seat adjuster assembly (driver seat)) (Including removal and installation)

·

Power seat lifter motor assembly (driver seat) (Including removal and installation)

·

Lumbar support adjuster assembly (driver seat) (Including removal and installation)

·

Power seat tilt motor assembly (driver seat) (Including removal and installation)


Initialize position control ECU Front power seat control system (for Gasoline model with memory) (Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B475753

Be sure to read Precaution thoroughly before servicing.



NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.REMOVE FRONT SEAT ASSEMBLY LH

Hide 3.REMOVE REAR SEAT ASSEMBLY

Hide 73706 4.REMOVE CHILD RESTRAINT SEAT ANCHOR BRACKET SUB-ASSEMBLY LH

Hide 64910N 5.REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

Hide 58410B 6.REMOVE DECK BOARD ASSEMBLY

Hide 58417H 7.REMOVE REAR NO. 3 FLOOR BOARD

Hide 64993 8.REMOVE REAR DECK FLOOR BOX (w/o Spare Tire)

Hide 58386 9.REMOVE REAR FLOOR FINISH PLATE

Hide 58577E 10.REMOVE REAR NO. 1 FLOOR MAT SUPPORT SIDE PLATE

Hide 67914B 11.REMOVE FRONT DOOR SCUFF PLATE LH

Hide 62112 12.REMOVE COWL SIDE TRIM BOARD LH

Hide 62312B 13.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

HINT:

Remove the front door opening trim weatherstrip LH so that the center pillar lower garnish LH can be removed.

Click hereVehicle Exterior>DOOR / HATCH>FRONT DOOR OPENING TRIM WEATHERSTRIP>REMOVAL


Hide 67918E 14.REMOVE REAR DOOR SCUFF PLATE LH

Hide 62332C 15.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

HINT:

Remove the rear door opening trim weatherstrip LH so that the center pillar lower garnish LH and rear seat No. 3 side garnish LH can be removed.

Click hereVehicle Exterior>DOOR / HATCH>REAR DOOR OPENING TRIM WEATHERSTRIP>REMOVAL


Hide 73233 16.REMOVE OUTER LAP BELT ANCHOR COVER

Hide 73220 17.REMOVE FRONT SEAT OUTER BELT ASSEMBLY LH

Hide 62414A 18.REMOVE LOWER CENTER PILLAR GARNISH LH

Hide 62552F 19.REMOVE REAR SEAT SIDE GARNISH LH

Hide 73708A 20.REMOVE TETHER ANCHOR BRACKET SET

Hide 58460D 21.REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY

Hide 64740E 22.REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH

Hide 86160Y 23.REMOVE REAR NO. 2 SPEAKER ASSEMBLY (w/ Woofer)

Hide 77306 24.REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY

a.
B523031C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the claw and guide to remove the fuel lid lock open lever sub-assembly in the direction indicated by the arrow as shown in the illustration.


b.
B478282

Detach the clamp and disconnect the fuel lid lock open lever sub-assembly from the fuel lid lock control cable assembly.


Hide 77377 25.REMOVE FUEL FILLER OPENING LID LOCK RETAINER

a.
B523032C01
0,0 0,0 false
V113147

Remove in this Direction


Turn the fuel filler opening lid lock retainer 90° clockwise and detach the claw as shown in the illustration.


b.
B523033C01
0,0 0,0 false
V113147

Remove in this Direction


Turn the fuel filler opening lid lock retainer a further 90° and detach the guide, then pull out the fuel filler opening lid lock retainer as shown in the illustration.


c.
B523034

Detach the claw and remove the fuel filler opening lid lock retainer.


Hide 77035 26.REMOVE FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY

a.

Partially remove the floor carpet.

HINT:

It is not necessary to fully remove the floor carpet. Partially remove it so that the fuel lid lock control cable sub-assembly can be removed.



b.

Detach the clamp and remove the fuel lid lock control cable sub-assembly as shown in the illustration.

B523035