Home › Vehicle Exterior › LIGHTING (EXT) › SWITCH HOUSING › 2019.02–2020.08
RM3620E _59 Vehicle Exterior _077130 LIGHTING (EXT) _0375599 SWITCH HOUSING A

LIGHTING (EXT)  SWITCH HOUSING  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during steering wheel switch housing removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative (-) auxiliary battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system
·

for A25A-FKS:

(Click here)

·

for M20A-FKS:

(Click here)


Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)
Reset back door close position Power back door system (for Gasoline model) (Click here)
Power back door initialization Power door lock control system (Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative (-) auxiliary battery terminal Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV model) (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Power back door initialization Power door lock control system (Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B475753

Be sure to read precaution thoroughly before servicing.



NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 58410B 2.REMOVE DECK BOARD ASSEMBLY (for HV Model)

Hide 58416K 3.REMOVE REAR NO. 2 FLOOR BOARD (for HV Model)

Hide 65351A 4.REMOVE BATTERY HOLE COVER (for HV Model)

Hide 5.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL


CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 6.REMOVE SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY

Hide 84650 7.REMOVE WINDSHIELD WIPER SWITCH ASSEMBLY

Hide 84329 8.REMOVE TURN SIGNAL SWITCH

Hide 84319 9.REMOVE STEERING WHEEL SWITCH HOUSING

a.
E404104

Using pliers, support the band clamp while loosened.


b.
E404105C01
0,0 0,0 false
V113147

Remove in this Direction
V100155

Protective Tape


Using a screwdriver, detach the claw and pull the steering wheel switch housing toward the rear of the vehicle to remove it.

HINT:

Tape the screwdriver tip before use.