Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SPIRAL CABLE › 2019.02–2020.08
RM3620E _58 Vehicle Interior _076036 SUPPLEMENTAL RESTRAINT SYSTEMS _0371432 SPIRAL CABLE A

SUPPLEMENTAL RESTRAINT SYSTEMS  SPIRAL CABLE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during spiral cable sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative (-) auxiliary battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system
·

for A25A-FKS:

(Click here)

·

for M20A-FKS:

(Click here)


Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)
Reset back door close position Power back door system (for Gasoline model) (Click here)
Power back door initialization Power door lock control system (Click here)
Steering sensor (Including removal and installation) Steering angle setting Parking assist monitor system (Click here)
Adjust steering angle Panoramic view monitor system (for Gasoline model) (Click here)
Steering angle neutral point Parking assist monitor system (Click here)
Parking support brake system (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative (-) auxiliary battery terminal Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Power back door initialization Power door lock control system (Click here)
Steering sensor (Including removal and installation) Steering angle setting Parking assist monitor system (Click here)
Adjust steering angle Panoramic view monitor system (for HV model) (Click here)
Steering angle neutral point Parking assist monitor system (Click here)
Parking support brake system (Click here)
Panoramic view monitor system (for HV model) (Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B475753

Be sure to read precaution thoroughly before servicing.



NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.PLACE FRONT WHEELS FACING STRAIGHT AHEAD

Hide 58410B 3.REMOVE DECK BOARD ASSEMBLY (for HV Model)

Hide 58416K 4.REMOVE REAR NO. 2 FLOOR BOARD (for HV Model)

Hide 65351A 5.REMOVE BATTERY HOLE COVER (for HV Model)

Hide 6.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL


CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 45100 7.REMOVE STEERING WHEEL ASSEMBLY

Hide 8.INSPECT SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY

a.

Check that the front wheels are facing straight ahead.


b.

Check that the spiral with sensor cable sub-assembly is center position.

OK:

The connector is at the top.

The top of the flat cable U-turn can be checked from the check window.


B525431C01
3.729,2.469 4.344,2.125 true 3.458,2.479 2.74,2.094 true 3.438,1.865 2.76,2 true 4.406,2.063 3.698,1.865 true 0.083,0.083 0.396,0.333 0.313,0.25 12 false *A 3.75,0.083 4.083,0.333 0.333,0.25 12 false *B 3.521,2.375 3.833,2.531 0.313,0.156 10 false *a 3.5,1.781 3.813,1.938 0.313,0.156 10 false *b
*A Type A *B Type B
*a Check Window *b Top of Flat Cable U-turn


NOTICE:

If the result is not as specified, it is possible that the spiral cable sub-assembly is broken. Replace the spiral cable sub-assembly with a new one.



Hide 45287 9.REMOVE LOWER STEERING COLUMN COVER

Hide 45286B 10.REMOVE UPPER STEERING COLUMN COVER

Hide 11.REMOVE SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY

NOTICE:
·

Do not replace the spiral with sensor cable sub-assembly with the auxiliary battery connected and the ignition switch on (IG).

·

Do not rotate the spiral with sensor cable sub-assembly with the auxiliary battery connected and the ignition switch on (IG).

·

When rotating the spiral with sensor cable sub-assembly to check the operation of the spiral with sensor cable sub-assembly (checking for abnormal noise, checking the Data List, etc.), make sure to perform the inspection with the steering wheel assembly installed.



a.
B525282C01
0.896,2.344 1.396,2.01 true 1.458,1.906 1.771,2.063 0.313,0.156 10 false *a
*a Slider
V113147

Slide in this Direction


Slide the slider to release the lock, and then disconnect the airbag connector.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.



b.
B525283C01
3.115,0.396 3.385,0.615 0.271,0.219 12 true *A
*A w/ Steering Heater


w/ Steering Heater:

i.

Disconnect the 4 connectors.



c.

w/o Steering Heater:

i.

Disconnect the 3 connectors.



d.
B525284

Detach the claw and clip to remove the spiral with sensor cable sub-assembly.


Hide 89245B 12.REMOVE STEERING SENSOR

NOTICE:
·

Remove the steering sensor from the spiral cable sub-assembly only when replacing the spiral cable sub-assembly.

·

Removing the steering sensor from the spiral cable sub-assembly without using a lock pin may result in a misaligned center position of the steering sensor. Therefore, make sure to use the lock pin provided with a new spiral cable when removing the steering sensor from the spiral cable sub-assembly.



a.
B525285

Install the lock pin to the steering sensor.

NOTICE:
·

Use the lock pin provided with a new spiral cable.

·

Do not remove the lock pin before the spiral cable is installed to the steering sensor.




b.
B525286

Detach the claw and guide to remove the steering sensor from the spiral cable sub-assembly.