The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during front seat side airbag assembly removal/installation are shown below.
After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.
After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
1. PRECAUTION
Be sure to read precaution thoroughly before servicing.
w/o Occupant Classification System:
for Gasoline Model with Occupant Classification System:
for HV Model with Occupant Classification System:
Wear protective gloves. Sharp areas on the parts may injure your hands.
There is risk of injury.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
58410B
2.REMOVE DECK BOARD ASSEMBLY (for HV Model)
58416K
3.REMOVE REAR NO. 2 FLOOR BOARD (for HV Model)
65351A
4.REMOVE BATTERY HOLE COVER (for HV Model)
5.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
for A25A-FKS:
for M20A-FKS:
for A25A-FXS:
Click hereGeneral>MAINTENANCE>A25A-FXS AUXILIARY BATTERY>REMOVAL
for A25B-FXS:
Click hereGeneral>MAINTENANCE>A25B-FXS AUXILIARY BATTERY>REMOVAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
6.REMOVE FRONT SEAT ASSEMBLY LH
72495
7.REMOVE VERTICAL ADJUSTING HANDLE LH (for Driver Side)
72552B
8.REMOVE RECLINING HINGE COVER LH
72526A
9.REMOVE RECLINING ADJUSTER RELEASE HANDLE LH
71849
10.REMOVE SEAT ADJUSTER COVER CAP LH (for Driver Side)
71812D
11.REMOVE FRONT SEAT CUSHION SHIELD LH (for Driver Side)
71811D
12.REMOVE FRONT SEAT CUSHION SHIELD RH (for Front Passenger Side)
71862
13.REMOVE FRONT SEAT INNER CUSHION SHIELD LH (for Driver Side)
71861
14.REMOVE FRONT SEAT INNER CUSHION SHIELD RH (for Front Passenger Side)
15.REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY LH
16.REMOVE SEPARATE TYPE FRONT SEATBACK COVER WITH PAD
73920A
17.REMOVE FRONT SEAT AIRBAG ASSEMBLY LH
|
Deployment Side |
When storing the front seat airbag assembly LH, keep the airbag deployment side facing upward.
If the airbag deploys for any reason, it may cause a serious accident.
Detach the wire harness clamp.
Remove the 2 nuts and front seat airbag assembly LH.
Do not reuse the nut.
If the installation surface or surrounding area of the front seat airbag assembly LH is deformed or damaged, replace the front seatback frame sub-assembly LH with a new one.