Home › Vehicle Interior › DOOR LOCK › FRONT DOOR LOCK › 2019.02–2020.08
RM3620E _58 Vehicle Interior _076046 DOOR LOCK _0377379 FRONT DOOR LOCK A

DOOR LOCK  FRONT DOOR LOCK  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the front door lock assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Removal and installation of auxiliary battery terminal Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV model) (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Power back door initialization Power door lock control system (Click here)
·

Power window regulator motor assembly LH

·

Power window regulator motor assembly RH

·

Front door window regulator sub-assembly LH

·

Front door window regulator sub-assembly RH

·

Front door glass sub-assembly LH

·

Front door glass sub-assembly RH

·

Front door glass run LH

·

Front door glass run RH


Initialize power window control system
·

Auto up and down function

·

Jam protection function

·

Catch protection function

·

Remote control function

·

Wireless transmitter-linked function

·

Key-linked function

·

Key-off operation function

·

Window open warning function


(Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Removal and installation of auxiliary battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system for A25A-FKS:(Click here)
for M20A-FKS:(Click here)
Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)
Reset back door close position Power back door system (for Gasoline model) (Click here)
Power back door initialization Power door lock control system (Click here)
·

Power window regulator motor assembly LH

·

Power window regulator motor assembly RH

·

Front door window regulator assembly LH

·

Front door window regulator assembly RH

·

Front door glass sub-assembly LH

·

Front door glass sub-assembly RH

·

Front door glass run LH

·

Front door glass run RH

·

Front door front glass run LH

·

Front door front glass run RH

·

Front Door No. 2 glass run LH

·

Front Door No. 2 glass run RH


Initialize power window control system
·

Auto up and down function

·

Jam protection function

·

Catch protection function

·

Remote control function

·

Wireless transmitter-linked function

·

Key-linked function

·

Key-off operation function

·

Window open warning function


(Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The procedure below is for the LH side.

·

When removing the front door glass sub-assembly LH, move the front door glass sub-assembly LH to the lowest position before disconnecting the negative (-) auxiliary battery terminal.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B475753

Be sure to read Precaution thoroughly before servicing.



NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 58410B 2.REMOVE DECK BOARD ASSEMBLY (for HV Model)

Hide 58416K 3.REMOVE REAR NO. 2 FLOOR BOARD (for HV Model)

Hide 65351A 4.REMOVE BATTERY HOLE COVER (for HV Model)

Hide 5.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL




d.

for A25B-FXS:

Click hereGeneral>MAINTENANCE>A25B-FXS AUXILIARY BATTERY>REMOVAL

CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



Hide 69278B 6.REMOVE FRONT DOOR INSIDE HANDLE BEZEL LH

Hide 74642A 7.REMOVE FRONT DOOR ASSIST GRIP COVER LH

Hide 8.REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)

Hide 9.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)

Hide 67602 10.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

Hide 68172A 11.REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP LH

Hide 68195B 12.REMOVE FRONT DOOR REAR BELT SEAL LH

Hide 68193C 13.REMOVE FRONT DOOR FRONT BELT SEAL LH

Hide 67832 14.REMOVE FRONT DOOR SERVICE HOLE COVER LH

Hide 68102 15.REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH

Hide 67664C 16.REMOVE DOOR FRAME GARNISH LH

Hide 68151D 17.REMOVE FRONT DOOR GLASS RUN LH

Hide 69802 18.REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH

Hide 67404F 19.REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH

Hide 69220 20.REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH (for Driver Side)

Hide 21.REMOVE FRONT DOOR LOCK CYLINDER ASSEMBLY LH (for Driver Side)

Hide 69312 22.REMOVE FRONT DOOR LOCK OPEN ROD LH

a.
B522042C01
3.104,1.156 2.583,0.542 true 3.125,1.156 3.344,1.344 0.219,0.188 10 true *1
*1 Snap
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)
V113149

Remove in this Direction (3)


Detach the snap as shown in the illustration.


b.

Remove the front door lock open rod LH in the direction indicated by the arrow show in the illustration.


Hide 69040A 23.REMOVE FRONT DOOR LOCK WITH MOTOR ASSEMBLY LH (w/o Double Locking System)

a.
B522045

Using a T30 "TORX" socket wrench, remove the 3 "TORX" screws and front door lock with motor assembly LH.


Hide 69318C 24.REMOVE DOOR LOCK WIRING HARNESS SEAL (w/o Double Locking System)

a.
B522046

When reusing front door lock with motor assembly LH:

i.

Remove the door lock wiring harness seal from the front door lock with motor assembly LH.



Hide 69036A 25.REMOVE FRONT DOOR LOCK COVER SUB-ASSEMBLY LH (w/o Double Locking System)

a.
B522047C01
0,0 0,0 false
V113147

Remove in this Direction
V100155

Protective Tape


Using a screwdriver with its tip wrapped with protective tape, detach the claw and open the front door lock cover sub-assembly LH.


b.
B522048

Detach the claw and remove the front door lock cover sub-assembly LH.


Hide 69720D 26.REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/o Double Locking System)

a.
B522049C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the clamp and remove the front door lock remote control cable assembly as shown in the illustration.


Hide 69760B 27.REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY (w/o Double Locking System)

a.
B522050C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the clamp and remove the front door inside locking cable assembly as shown in the illustration.


Hide 69040A 28.REMOVE FRONT DOOR LOCK WITH MOTOR ASSEMBLY LH (w/ Double Locking System)

a.
B532292

Using a T30 "TORX" socket wrench, remove the 3 "TORX" screws and front door lock with motor assembly LH.


Hide 69318C 29.REMOVE DOOR LOCK WIRING HARNESS SEAL (w/ Double Locking System)

a.
B522046

When reusing front door lock with motor assembly LH:

i.

Remove the door lock wiring harness seal from the front door lock with motor assembly LH.



Hide 69720D 30.REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/ Double Locking System)

a.
B532296C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the clamp and remove the front door lock remote control cable assembly as shown in the illustration.


Hide 69760B 31.REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY (w/ Double Locking System)

a.
B532294C01
0,0 0,0 false
V113147

Remove in this Direction
V100155

Protective Tape


Using a screwdriver with its tip wrapped with protective tape, detach the claw and open the cover.


b.
B532297C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the clamp and remove the front door inside locking cable assembly as shown in the illustration.