Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR › 2019.02–2020.08
RM3620E _59 Vehicle Exterior _076335 DOOR / HATCH _0377461 FRONT DOOR A

DOOR / HATCH  FRONT DOOR  DISASSEMBLY  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front door disassembly/reassembly are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Removal and installation of auxiliary battery terminal Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV model) (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Power back door initialization Power door lock control system (Click here)
·

Power window regulator motor assembly LH

·

Power window regulator motor assembly RH

·

Front door window regulator sub-assembly LH

·

Front door window regulator sub-assembly RH

·

Front door glass sub-assembly LH

·

Front door glass sub-assembly RH

·

Front door glass run LH

·

Front door glass run RH


Initialize power window control system
·

Auto up and down function

·

Jam protection function

·

Catch protection function

·

Remote control function

·

Wireless transmitter-linked function

·

Key-linked function

·

Key-off operation function

·

Window open warning function


(Click here)
·

Outer rear view mirror assembly LH

·

Outer rear view mirror assembly RH


Side television camera view adjustment Panoramic view monitor system (for HV model) (Click here)
·

Side television camera assembly LH or outer rear view mirror assembly LH

·

Side television camera assembly RH or outer rear view mirror assembly RH


Television camera view adjustment Panoramic view monitor system (for HV model) (Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Removal and installation of auxiliary battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system for A25A-FKS:(Click here)
for M20A-FKS:(Click here)
Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)
Reset back door close position Power back door system (for Gasoline model) (Click here)
Power back door initialization Power door lock control system (Click here)
·

Power window regulator motor assembly LH

·

Power window regulator motor assembly RH

·

Front door window regulator assembly LH

·

Front door window regulator assembly RH

·

Front door glass sub-assembly LH

·

Front door glass sub-assembly RH

·

Front door glass run LH

·

Front door glass run RH

·

Front door front glass run LH

·

Front door front glass run RH

·

Front Door No. 2 glass run LH

·

Front Door No. 2 glass run RH


Initialize power window control system
·

Auto up and down function

·

Jam protection function

·

Catch protection function

·

Remote control function

·

Wireless transmitter-linked function

·

Key-linked function

·

Key-off operation function

·

Window open warning function


(Click here)
·

Outer rear view mirror assembly LH

·

Outer rear view mirror assembly RH


Side television camera view adjustment Panoramic view monitor system (for Gasoline model) (Click here)
·

Side television camera assembly LH or outer rear view mirror assembly LH

·

Side television camera assembly RH or outer rear view mirror assembly RH


Television camera view adjustment Panoramic view monitor system (for Gasoline model) (Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The procedure below is for the LH side.

·

Before performing disassembly work on the front door, make sure that the front door glass is fully open and be sure to disconnect the cable from the negative (-) auxiliary battery terminal.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B475753

Be sure to read Precaution thoroughly before servicing.



NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 58410B 2.REMOVE DECK BOARD ASSEMBLY (for HV Model)

Hide 58416K 3.REMOVE REAR NO. 2 FLOOR BOARD (for HV Model)

Hide 65351A 4.REMOVE BATTERY HOLE COVER (for HV Model)

Hide 5.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL




d.

for A25B-FXS:

Click hereGeneral>MAINTENANCE>A25B-FXS AUXILIARY BATTERY>REMOVAL

CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



Hide 69278B 6.REMOVE FRONT DOOR INSIDE HANDLE BEZEL LH

a.
B521991

Detach the claw and remove the front door inside handle bezel LH.


Hide 74642A 7.REMOVE FRONT DOOR ASSIST GRIP COVER LH

a.
B521992C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape to the front door trim board sub-assembly LH as shown in the illustration.


b.
B521993C01
1.917,0.927 2.073,1.125 0.156,0.198 10 true 1 1.688,0.99 1.844,1.188 0.156,0.198 10 true 2 1.813,1.729 1.969,1.927 0.156,0.198 10 true 2 1.438,1.792 1.594,1.99 0.156,0.198 10 true 3 2.219,0.521 2.333,0.708 0.115,0.188 10 true 3 1.063,1.146 1.219,1.344 0.156,0.198 10 true 4 1.104,1.896 1.26,2.094 0.156,0.198 10 true 4 0.698,1.979 0.854,2.177 0.156,0.198 10 true 5 0.688,1.219 0.844,1.417 0.156,0.198 10 true 5 2.094,0.771 2.229,0.948 0.135,0.177 10 true 2 2.75,1.021 2.885,1.198 0.135,0.177 10 true 2 1.396,1.073 1.552,1.271 0.156,0.198 10 true 3 2.844,0.698 2.958,0.885 0.115,0.188 10 true 3 2.823,0.24 2.938,0.427 0.115,0.188 10 true 4
V113147

Remove in this Direction


Using a moulding remover A, detach the clip.


c.

Detach the claw in the order shown in the illustration.


d.
B521994C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the guide in the direction indicated by the arrow shown in the illustration and remove the front door assist grip cover LH.


Hide 8.REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)

a.
B521995C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape around the multiplex network master switch assembly with front door armrest base panel.


b.
B521996C01
0,0 0,0 false
V113147

Remove in this Direction


Using a moulding remover A, detach the guide and claw as shown in the illustration.


c.
B521997C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the guide in the direction indicated by the arrow shown in the illustration and remove the multiplex network master switch assembly with front door armrest base panel.


d.

Disconnect the 2 connectors.


Hide 84040 9.REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY (for Driver Side)

Hide 84870A 10.REMOVE OUTER MIRROR SWITCH ASSEMBLY (for Driver Side)

Hide 11.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)

a.
B521998C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape around the power window regulator switch assembly with front door armrest base panel.


b.
B521999C01
0,0 0,0 false
V113147

Remove in this Direction


Using a moulding remover A, detach the guide and claw as shown in the illustration.


c.
B522000C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the guide in the direction indicated by the arrow shown in the illustration and remove the power window regulator switch assembly with front door armrest base panel.


d.

w/ Door Control Switch:

i.

Disconnect the 2 connectors.



e.

w/o Door Control Switch:

i.

Disconnect the connector.



Hide 84810 12.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Front Passenger Side)

Hide 84930 13.REMOVE DOOR CONTROL SWITCH ASSEMBLY (w/ Door Control Switch)

Hide 67602 14.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

a.
B522001C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape to the front door panel as shown in the illustration.


b.
B522002

Remove the 3 screws.


c.
B522003C01
2.698,3.115 2.833,3.292 0.135,0.177 10 true 1 2.156,3.188 2.292,3.365 0.135,0.177 10 true 2 1.635,3.25 1.771,3.427 0.135,0.177 10 true 3 1.323,3.01 1.458,3.156 0.135,0.146 10 true 4 1.167,2.51 1.302,2.656 0.135,0.146 10 true 5 3.031,2.667 3.167,2.844 0.135,0.177 10 true 2 3.094,2.219 3.229,2.396 0.135,0.177 10 true 3
V113146

Place Hand Here
V113147

Remove in this Direction


Place your hand at the position shown in the illustration, and while pulling the front door trim board sub-assembly LH toward you, detach the clip and disconnect the front door trim board sub-assembly LH from the front door panel.

HINT:
·

Detach the clip in the order shown in the illustration.

·

Securely detach the clips one by one.




d.
B522004C01
0.708,1.406 0.823,1.594 0.115,0.188 10 true 1 1.156,1.396 1.271,1.583 0.115,0.188 10 true 2 1.521,1.396 1.635,1.583 0.115,0.188 10 true 3 1.885,1.375 2,1.563 0.115,0.188 10 true 4 2.208,1.344 2.323,1.531 0.115,0.188 10 true 5 2.51,1.302 2.625,1.49 0.115,0.188 10 true 6 2.625,1.76 2.74,1.948 0.115,0.188 10 true 7 0.385,1.698 0.5,1.885 0.115,0.188 10 true 8 2.875,1.333 3,1.51 0.125,0.177 10 true 9
V113147

Remove in this Direction


Pull the front door trim board sub-assembly LH in the direction indicated by the arrow shown in the illustration to detach the claw and clip to remove the front door trim board sub-assembly LH.

HINT:

Detach the claw and clips in the order shown in the illustration.



e.
B522005C01
2.146,0.823 2.729,0.823 true 2.313,1.385 2.552,1.792 true 2.802,0.729 3,0.917 0.198,0.188 10 true *1 2.51,1.833 2.719,2.01 0.208,0.177 10 true *2
*1 Front Door Inside Locking Cable Assembly
*2 Front Door Lock Remote Control Cable Assembly
V113147

Remove in this Direction


Detach the clamp and disconnect the front door lock remote control cable assembly LH and front door inside locking cable assembly LH as shown in the illustration.


f.
B522006

w/ Seat Memory Switch:

i.

Disconnect the connector.



Hide 84927 15.REMOVE SEAT MEMORY SWITCH (w/ Seat Memory Switch)

Hide 69206B 16.REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY LH

a.
B522007

Detach the clamp and claw.


b.
B522008C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the front door inside handle sub-assembly LH in the direction indicated by the arrow as shown in the illustration.


Hide 68172A 17.REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP LH

a.
B522009C01
0,0 0,0 false
V113147

Remove in this Direction
V100155

Protective Tape


Using a clip remover with its tip wrapped with protective tape, detach the clip.


b.

Detach the guide and roll up the front door weatherstrip LH enough that the front door inner glass weatherstrip LH can be removed.


c.
B522010C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the front door inner glass weatherstrip LH with front door rear belt seal LH as shown in the illustration.


Hide 68195B 18.REMOVE FRONT DOOR REAR BELT SEAL LH

a.
B522011C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the front door rear belt seal LH from the front door inner glass weatherstrip LH as shown in the illustration.


Hide 68193C 19.REMOVE FRONT DOOR FRONT BELT SEAL LH

a.
B522012C01
0,0 0,0 false
V113147

Remove in this Direction
V100155

Protective Tape


Using a clip remover with its tip wrapped with protective tape, detach the clip.


b.

Detach the guide and roll up the front door weatherstrip LH enough that the front door front belt seal LH can be removed.


c.
B522013C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the front door front belt seal LH as shown in the illustration.


Hide 87964 20.REMOVE OUTER MIRROR INSTALL HOLE COVER LH

Hide 87940 21.REMOVE OUTER REAR VIEW MIRROR ASSEMBLY LH

Hide 86160 22.REMOVE FRONT NO. 1 SPEAKER ASSEMBLY

Hide 67832 23.REMOVE FRONT DOOR SERVICE HOLE COVER LH

a.
B522014

Disconnect the connector.


b.

Detach the clamp.


c.
B522015C01
0.99,2.344 0.99,2.167 0.99,2.167 0.771,2.167 false 0.896,2.719 0.896,2.927 0.896,2.927 0.792,2.927 false 0.594,2.083 0.906,2.281 0.313,0.198 10 false *a 0.625,2.844 0.938,3.042 0.313,0.198 10 false *b
*a Location Mark
*b Bead Mark
V113147

Turn in this Direction
V100135

Service Hole Cover Clip


Check that the service hole cover clip knob and bead mark are aligned.


d.

Turn the service hole cover clip 45° clockwise to the location mark and then remove the service hole cover clip.

HINT:

Use the same procedure for the other service hole cover clips.



e.
B522016C01
0,0 0,0 false
V100155

Protective Tape


Using a clip remover with its tip wrapped with protective tape, detach the clip.


f.
B522017C01
0,0 0,0 false
V113147

Remove in this Direction


Pull out the front door lock remote control cable assembly LH and front door inside locking cable assembly LH from the front door service hole cover LH.


Hide 68102 25.REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH

a.
B522018

Remove the hole plug.


b.

for Driver Side:

i.

Connect the multiplex network master switch assembly connector.



c.

for Front Passenger Side:

i.

Connect the power window regulator switch assembly connector.



d.

Connect the cable to the negative (-) auxiliary battery terminal.






e.

Turn the ignition switch to ON.


f.

Move the front door glass sub-assembly LH until the installation bolts can be seen.


g.

Turn the ignition switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.


ii.

iii.

iv.

for A25B-FXS:

Click hereGeneral>MAINTENANCE>A25B-FXS AUXILIARY BATTERY>REMOVAL

CAUTION:
B394718

·

After disconnecting the cable from the negative (-) auxiliary battery terminal, wait for at least 90 seconds to start the operation.

·

If the airbag deploys for any reason, it may cause a serious accident.





i.

for Driver Side:

i.

Disconnect the multiplex network master switch assembly connector.



j.

for Front Passenger Side:

i.

Disconnect the power window regulator switch assembly connector.



k.
B522019C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape around the front door panel as shown in the illustration.


l.
B522020

Remove the 2 bolts.

NOTICE:

After the bolts are removed, do not allow the front door glass sub-assembly LH to fall.



m.
B522021C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Remove the front door glass sub-assembly LH in the direction indicated by the arrows, in the order shown in the illustration.

NOTICE:

Be careful not to damage the front door glass sub-assembly LH.



Hide 67664C 26.REMOVE DOOR FRAME GARNISH LH

a.
B522022C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Detach the guide and remove the door frame garnish LH in the direction indicated by the arrows, in the order shown in the illustration.


Hide 68151D 27.REMOVE FRONT DOOR GLASS RUN LH

a.
B522023C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Remove the front door glass run LH as shown in the illustration.


Hide 69802 28.REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH

a.
B522024C02
0,0 0,0 false
V100135

Nut
V100136

Connector


Disconnect the connector.


b.

Remove the 7 nuts and the front door window regulator sub-assembly LH.

NOTICE:

Do not damage the front door panel with the front door window regulator sub-assembly LH.


HINT:
B522025C01
0,0 0,0 false
V113147

Remove in this Direction


When removing the front door window regulator assembly LH, pull it out from the service hole as shown in the illustration.



Hide 85720C 29.REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

Hide 67404F 30.REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH

a.
B522026

Remove the bolt.


b.

Detach the guide and remove the front door rear lower frame sub-assembly LH.


Hide 67402F 31.REMOVE FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY LH

a.
B522027C01
0,0 0,0 false
V113147

Lift up in this Direction


Lift up the front door weatherstrip LH and remove the screw as shown in the illustration.


b.

Remove the screw.


c.
B522028C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Remove the 3 bolts.


d.

Remove the front door front lower frame sub-assembly LH in the direction indicated by the arrows, in the order shown in the illustration.


Hide 68126 32.REMOVE FRONT DOOR FIX WINDOW GLASS LH

a.
B522029C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the front door fix window glass LH as shown in the illustration.


Hide 75712B 33.REMOVE FRONT DOOR BELT MOULDING LH

Hide 69220 34.REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH

a.
B522030C01
0,0 0,0 false
V113147

Remove in this Direction
V100155

Protective Tape


w/ Entry and Start System:

i.

Using a screwdriver with its tip wrapped with protective tape, detach the claw and open the connector cover as shown in the illustration.


ii.
B522031C01
0,0 0,0 false
V100155

Protective Tape


Using a screwdriver with its tip wrapped with protective tape, detach the claw to disconnect the connector and connector cover as shown in the illustration.



b.
B522032C01
1.177,0.625 1.531,0.771 true 0.938,0.479 1.156,0.688 0.219,0.208 10 true *1
*1 Holder
V113147

Remove in this Direction


Detach the holder as shown in the illustration.


c.
B522033C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the front door outside handle assembly LH by sliding and pulling it in the direction indicated by the arrow in the illustration.


Hide 35.REMOVE FRONT DOOR LOCK CYLINDER ASSEMBLY LH (for Driver Side)

a.
B522034

Remove the hole plug.


b.
B522035

Using a T30 "TORX" socket wrench, loosen the "TORX" screw.


c.
B522036C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the front door lock cylinder assembly LH as shown in the illustration.


Hide 69217E 36.REMOVE FRONT DOOR OUTSIDE HANDLE COVER RH (for Front Passenger Side)

a.
B522037

Remove the hole plug.


b.
B522038

Using a T30 "TORX" socket wrench, loosen the "TORX" screw.


c.
B522039C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the claw and remove the front door outside handle cover RH as shown in the illustration.


Hide 69241H 37.REMOVE FRONT DOOR FRONT OUTSIDE HANDLE PAD

a.
B522040

Detach the claw and guide to remove the front door front outside handle pad.


Hide 69242F 38.REMOVE FRONT DOOR REAR OUTSIDE HANDLE PAD

a.
B522041

Detach the guide and remove the front door rear outside handle pad.


Hide 69312 39.REMOVE FRONT DOOR LOCK OPEN ROD LH

a.
B522042C01
3.104,1.156 2.583,0.542 true 3.125,1.156 3.344,1.344 0.219,0.188 10 true *1
*1 Snap
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)
V113149

Remove in this Direction (3)


Detach the snap as shown in the illustration.


b.

Remove the front door lock open rod LH in the direction indicated by the arrow shown in the illustration.


Hide 69202A 40.REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH

a.
B522043C01
0.167,0.083 0.469,0.323 0.302,0.24 10 true *a 0.167,2.448 0.469,2.688 0.302,0.24 10 true *b
*a Inside
*b Outside


Using a T30 "TORX" socket wrench, loosen the "TORX"screw.


b.

Detach the guide and remove the front door outside handle frame sub-assembly LH.


c.
B522044

w/ Entry and Start System:

i.

Detach the wire harness clamp.



Hide 69040A 41.REMOVE FRONT DOOR LOCK WITH MOTOR ASSEMBLY LH (w/o Double Locking System)

Hide 69318C 42.REMOVE DOOR LOCK WIRING HARNESS SEAL (w/o Double Locking System)

a.

When reusing front door lock with motor assembly LH:

Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>REMOVAL


Hide 69036A 43.REMOVE FRONT DOOR LOCK COVER SUB-ASSEMBLY LH (w/o Double Locking System)

Hide 69720D 44.REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/o Double Locking System)

Hide 69760B 45.REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY (w/o Double Locking System)

Hide 69040A 46.REMOVE FRONT DOOR LOCK WITH MOTOR ASSEMBLY LH (w/ Double Locking System)

Hide 69318C 47.REMOVE DOOR LOCK WIRING HARNESS SEAL (w/ Double Locking System)

a.

When reusing front door lock with motor assembly LH:

Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>REMOVAL


Hide 69720D 48.REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/ Double Locking System)

Hide 69760B 49.REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY (w/ Double Locking System)

Hide 68620 50.REMOVE FRONT DOOR CHECK ASSEMBLY LH

a.
B522051C01
0,0 0,0 false
V100135

Bolt (A)
V100136

Bolt (B)


Remove the 2 bolts (A), bolt (B) and front door check assembly LH.


Hide 67862 51.REMOVE FRONT DOOR WEATHERSTRIP LH

a.
B522052C01
0,0 0,0 false
V100155

Protective Tape


Using a clip remover with its tip wrapped with protective tape, detach the clip.


b.
B522053C01
0,0 0,0 false
V100155

Protective Tape


Using a screwdriver with its tip wrapped with protective tape, detach the clip and remove the front door weatherstrip LH.


Hide 75756D 52.REMOVE FRONT DOOR WINDOW FRAME MOULDING LH (CENTER PILLAR SIDE)

Hide 67856B 53.REMOVE FRONT DOOR PANEL PROTECTOR LH

Hide 75792 54.REMOVE DOOR WINDOW FRAME MOULDING CLIP

a.
B524160

Detach the claw and remove the door window frame moulding clip.

HINT:

Perform the following procedure only when replacement of a door window frame moulding clip in necessary.



Hide 75754A 55.REMOVE FRONT DOOR UPPER WINDOW FRAME MOULDING LH

Hide 67864B 56.REMOVE FRONT DOOR NO. 2 WEATHERSTRIP LH

a.
B522054

Using a screwdriver with its tip wrapped with protective tape, detach the clip and remove the front door No. 2 weatherstrip LH.


Hide 75074 57.REMOVE FRONT DOOR LOWER OUTSIDE MOULDING SUB-ASSEMBLY LH

Hide 58.REMOVE SCREW GROMMET

a.
B522055

Detach the claw and remove the screw grommet.

HINT:

Use the same procedure described for the other side.



Hide 59.REMOVE HOLE PLUG

a.
B522057

Remove the hole plug.

HINT:

Use the same procedure described for the other side.



Hide 67001A 60.REMOVE FRONT DOOR PANEL CUSHION

a.
B522056

Detach the claw and remove the front door panel cushion.

HINT:

Use the same procedure described for the other side.



Hide 75966B 61.REMOVE FRONT DOOR NO. 4 STRIPE LH (w/ Black Out Tape)

Hide 75986G 62.REMOVE FRONT DOOR OUTSIDE STRIPE LH (w/ Black Out Tape)

Hide 75922M 63.REMOVE NO. 1 BLACK OUT TAPE LH (w/ Black Out Tape)