Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER (for LHD without Vacuum Brake Booster) › from 2019.02
RM3620E _54 Brake _076411 BRAKE SYSTEM (OTHER) _0377038 BRAKE BOOSTER(for LHD without Vacuum Brake Booster) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER(for LHD without Vacuum Brake Booster)  INSTALLATION  


PROCEDURE

Hide 44785C 1.INSTALL BRAKE BOOSTER GASKET

a.

Install a new brake booster gasket to the brake booster with master cylinder assembly.


Hide 47210L 2.INSTALL BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

a.
C408170C02
1.719,2.646 2.219,2.646 false 1.438,3.833 0.75,4.125 0.75,4.125 1.385,4.125 true 1.719,3.063 0.583,2.583 0.583,2.583 1.313,3.094 true 2.74,3.469 2.917,3.677 2.917,3.677 3.083,3.677 false 2.406,3.583 2.698,3.938 2.698,3.938 2.865,3.938 false 2.281,2.583 2.594,2.74 0.313,0.156 10 false *1 0.396,2.469 0.708,2.625 0.313,0.156 10 false *2 3.146,3.615 3.427,3.823 0.281,0.208 10 false *3 2.917,3.854 3.229,4.01 0.313,0.156 10 false *4 0.563,4.042 0.875,4.198 0.313,0.156 10 false *5
*1 Connector Portion
*2 Union
*3 Push Rod Clevis
*4 Boot
*5 Front No. 2 Brake Tube


Install the brake booster with master cylinder assembly with the 4 nuts.

Torque:
12.7 N*m (130 kgf*cm, 9 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not carry the brake booster with master cylinder assembly by the portion shown in the illustration.

·

Be careful not to allow brake fluid to enter the connector of ECU.

·

If installing a new brake booster with master cylinder assembly, do not remove the hole plugs before connecting the brake lines because the brake booster with master cylinder is filled with brake fluid.




b.
C408178

Engage the clamp to install a new brake tube clamp to the No. 4 front brake tube.


c.
C409062

Engage the clamp to install the No. 4 front brake tube with brake tube clamp to the brake line.


d.
C409061

Engage the clamp and install a new brake tube clamp to the vehicle body.


e.

Engage the 4 clamps to install the brake tube clamp to the brake lines.


f.
C408175

Engage the 8 clamps to install the 2 new brake tube clamps to the brake lines.


g.
C408167C02
0.938,0.438 1.104,0.438 1.104,0.438 1.26,0.688 true 2.021,1.146 2.323,1.792 2.323,1.792 2.49,1.792 true 1.938,0.552 2.271,0.219 2.271,0.219 2.438,0.219 true 1.5,1.375 1.667,1.375 1.667,1.375 1.99,0.958 true 1.594,0.948 1.76,0.948 1.76,0.948 1.927,0.781 true 2.5,0.135 2.74,0.333 0.24,0.198 10 true *a 1.406,0.854 1.625,1.01 0.219,0.156 10 true *b 1.313,1.281 1.542,1.448 0.229,0.167 10 true *c 2.542,1.698 2.792,1.865 0.25,0.167 10 true *d 0.729,0.333 0.979,0.5 0.25,0.167 10 true *e
*a To Front Wheel Cylinder LH
*b To Rear Wheel Cylinder RH
*c To Brake Booster Pump Assembly
*d To Rear Wheel Cylinder LH
*e To Front Wheel Cylinder RH


Temporarily install each brake line to the correct position on the brake booster with master cylinder assembly as shown in the illustration.


h.
C408169C01
2.917,3 2.75,3 2.75,3 2.75,2.667 false 1.75,2.948 2.063,3.104 0.313,0.156 10 false *a 2.979,2.927 3.24,3.115 0.26,0.188 10 false *b
*a Torque Wrench Fulcrum Length
*b Union Nut Wrench


Using a union nut wrench, tighten each brake line.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow the brake lines to twist or interfere with other parts or the vehicle body during tightening.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

13.4 N*m (137 kgf*cm, 10 ft.*lbf)




i.
C408166C01
0,0 0,0 false
V113147

Connect the connector
V113148

Lock the lock lever


Connect the connector to the brake booster with master cylinder assembly.

NOTICE:
·

Make sure that the connector is locked securely.

·

Make sure that the actuator connector can be connected smoothly.

·

Do not allow water, oil or dirt to enter the connector.




j.

Engage the clamp.


Hide 47314 3.CONNECT NO. 4 FRONT BRAKE TUBE

a.
C409063C01
2.854,3.073 2.688,3.073 2.688,3.073 2.688,2.74 false 1.802,3.01 2.115,3.167 0.313,0.156 10 false *a 2.917,2.99 3.229,3.146 0.313,0.156 10 false *b
*a Torque Wrench Fulcrum Length
*b Union Nut Wrench


Using a union nut wrench, connect the No. 4 front brake tube.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow the brake lines to twist or interfere with other parts or the vehicle body during tightening.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

13.4 N*m (137 kgf*cm, 10 ft.*lbf)




Hide 44551C 4.CONNECT NO. 1 BRAKE ACTUATOR TUBE

a.
C408174

Install the No. 1 brake actuator tube with the 2 nuts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


Hide 47233 5.INSTALL RESERVOIR BRACKET

a.

Temporarily install the reservoir bracket with the bolt and 2 nuts.


b.
C408164N01
3.01,0.458 3.167,0.656 0.156,0.198 10 true 1 1.75,1.938 1.906,2.135 0.156,0.198 10 true 2 1.313,0.094 1.469,0.292 0.156,0.198 10 true 3

Tighten the bolt and 2 nuts in the order shown in the illustration..

Torque:
19 N*m (194 kgf*cm, 168 in.*lbf)


Hide 6.TEMPORARILY INSTALL BRAKE MASTER CYLINDER RESERVOIR WITH RESERVOIR HOSE

a.

Temporaily install the brake master cylinder reservoir to the reservoir bracket.


Hide 44571A 7.CONNECT NO. 1 BRAKE ACTUATOR HOSE

a.
C408171C02
1.615,1.688 1.781,1.688 1.781,1.688 2.01,2.313 true 2.49,0.188 2.948,0.385 0.458,0.198 10 false 90° 1.542,0.188 2,0.385 0.458,0.198 10 false 90° 1.417,1.594 1.615,1.802 0.198,0.208 10 true *a
*a Identification Mark
V100136

Up


Connect the No. 1 brake actuator hose to the brake master cylinder reservoir assembly, and slide the clip to secure it.

NOTICE:
·

Make sure to match the identification mark on the No. 1 brake actuator hose and brake master cylinder reservoir assembly.

·

When connecting the No. 1 brake actuator hose, face the identification mark up.

·

Make sure to install the hose to the proper location.

·

Install the clip within the range shown in the illustration.




Hide 47234L 8.CONNECT NO. 1 RESERVOIR HOSE

a.
C408173C01
1.458,1.875 1.833,1.667 1.833,1.667 2,1.667 true 2.031,1.573 2.219,1.76 0.188,0.188 10 true *a 2.5,0.198 2.958,0.396 0.458,0.198 10 false 90° 1.552,0.198 2.01,0.396 0.458,0.198 10 false 90°
*a Identification Mark
V100136

Up


Connect the No. 1 reservoir hose to the brake booster with master cylinder assembly, and slide the clip to secure it.

NOTICE:
·

Make sure to match the identification mark on the No. 1 reservoir hose and brake booster with master cylinder assembly.

·

When connecting the No. 1 reservoir hose, face the identification mark up.

·

Make sure to install the hose to the proper location.

·

Install the clip within the range shown in the illustration.




Hide 47235G 9.CONNECT NO. 2 RESERVOIR HOSE

a.
C408172C02
1.688,2.292 2.063,2.083 2.063,2.083 2.229,2.083 true 2.281,2 2.469,2.188 0.188,0.188 10 true *a 2.5,0.198 2.958,0.396 0.458,0.198 10 false 90° 1.552,0.198 2.01,0.396 0.458,0.198 10 false 90°
*a Identification Mark
V100136

Up


Connect the No. 2 reservoir hose to the brake booster with master cylinder assembly, and slide the clip to secure it.

NOTICE:
·

Make sure to match the identification mark on the No. 2 reservoir hose and brake booster with master cylinder assembly.

·

When connecting the No. 2 reservoir hose, face the identification mark up.

·

Make sure to install the hose to the proper location.

·

Install the clip within the range shown in the illustration.




Hide 44551C 10.BLEED NO. 1 BRAKE ACTUATOR TUBE

a.

Add brake fluid into the brake master cylinder reservoir assembly.


b.
C409060C01
0.146,1.656 0.229,0.906 0.229,0.906 0.396,0.906 true 0.406,0.823 0.646,1.031 0.24,0.208 10 true *1
*1 No. 1 Brake Actuator Tube


Lift up the brake master cylinder reservoir assembly as far as possible and rock it back and forth to bleed air from the No. 1 brake actuator tube.

NOTICE:
·

Do not damage the hoses or tubes.

·

Do not spill brake fluid.

·

Continue this procedure until only a minor amount of air remains in the brake actuator tube.




Hide 47220D 11.INSTALL BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY

a.
C408163

Install the brake master cylinder reservoir assembly with the 2 nuts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 13.CONNECT WIRE HARNESS

a.
C409059

Connect the connector to the brake pedal stroke sensor assembly.


b.

Engage the 2 clamps to connect the wire harness to the brake pedal support assembly.


Hide 84340 15.INSTALL STOP LIGHT SWITCH ASSEMBLY

Hide 87211 16.INSTALL NO. 1 AIR DUCT

Hide 73900 17.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

Hide 18.FILL RESERVOIR WITH BRAKE FLUID

Hide 19.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 23.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 24.PERFORM INITIALIZATION AND CALIBRATION OF LINEAR SOLENOID VALVE AND ZERO POINT OF YAW RATE AND ACCELERATION SENSOR