Home › Vehicle Interior › SEAT › CLIMATE CONTROL SEAT SWITCH › from 2020.08
RM3620E _58 Vehicle Interior _076405 SEAT _0377514 CLIMATE CONTROL SEAT SWITCH A

SEAT  CLIMATE CONTROL SEAT SWITCH  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during refreshing seat switch removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative (-) battery terminal Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV model) (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Power back door initialization Power door lock control system (Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative (-) battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system for A25A-FKS:(Click here)
for M20A-FKS:(Click here)
Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)
Reset back door close position Power back door system (for Gasoline model) (Click here)
Power back door initialization Power door lock control system (Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


CAUTION:
B458500

Be sure to read precaution thoroughly before servicing.



NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 58410B 1.REMOVE DECK BOARD ASSEMBLY (w/ Airbag Cut Off Indicator Light, for HV Model)

Hide 58416K 2.REMOVE REAR NO. 2 FLOOR BOARD (w/ Airbag Cut Off Indicator Light, for HV Model)

Hide 65351A 3.REMOVE BATTERY HOLE COVER (w/ Airbag Cut Off Indicator Light, for HV Model)

Hide 4.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL (w/ Airbag Cut Off Indicator Light)


CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 58804A 6.REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY

Hide 861C0 7.REMOVE MOBILE WIRELESS CHARGER CRADLE ASSEMBLY (w/ Wireless Charger)

Hide 58813 8.REMOVE UPPER CONSOLE BOX (w/o Wireless Charger)

Hide 58805C 9.REMOVE REAR UPPER CONSOLE PANEL SUB-ASSEMBLY

Hide 55900 10.REMOVE AIR CONDITIONING CONTROL ASSEMBLY

Hide 55434B 11.REMOVE LOWER CENTER INSTRUMENT PANEL FINISH PANEL

Hide 84752 12.REMOVE REFRESHING SEAT SWITCH

a.
B525173C02
0,0 0,0 false
V113147

Remove in this Direction
V100155

Protective Tape


Using a thin-bladed screwdriver, detach the claw to remove the refreshing seat switch.

HINT:

Tape the thin-bladed screwdriver tip before use.