Home › Engine / Hybrid System › A25A-FKS (ENGINE MECHANICAL) › CYLINDER HEAD GASKET › from 2020.08
RM3620E _51 Engine / Hybrid System _076317 A25A-FKS ENGINE MECHANICAL _0371509 CYLINDER HEAD GASKET A

A25A-FKS ENGINE MECHANICAL  CYLINDER HEAD GASKET  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during cylinder head gasket removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Battery terminal is disconnected/reconnected Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system (Click here)
Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)
Reset back door close position Power back door system (for Gasoline model) (Click here)
Power back door initialization Power door lock control system (Click here)
Replacement of ECM
w/ Canister Pump Module:

Perform Vehicle Identification Number (VIN) registration


DTC P063051 is output (Click here)
w/o Canister Pump Module:

Perform Vehicle Identification Number (VIN) or frame number registration


(Click here)
ECU communication ID registration Engine start function See Service Bulletin for the registration method.
for UB80E:

If transaxle compensation code read from ECM

-

Perform reset memory

-

Transfer transaxle compensation code

-

Perform road test to allow ECM to learn



·

Large shift shock

·

Deterioration of fuel efficiency


for Initialization:
(Click here)
for Registration:
(Click here)
for UB80F:

If transaxle compensation code read from ECM

-

Perform reset memory

-

Transfer transaxle compensation code

-

Perform road test to allow ECM to learn



·

Large shift shock

·

Deterioration of fuel efficiency


for Initialization:
(Click here)
for Registration:
(Click here)
·

Gas leak from exhaust system is repaired

·

Replacement of throttle body with motor assembly

·

Replacement of cam timing control motor with EDU assembly

·

Removal and installation of a cam timing control motor with EDU assembly

·

Replacement of camshaft timing gear assembly

·

Removal and installation of a camshaft timing gear assembly

·

Replacement of cylinder head sub-assembly

·

Replacement of camshaft (for intake or exhaust camshaft)

·

Replacement of camshaft timing exhaust gear assembly

·

Replacement of port fuel injector assembly

·

Replacement of direct fuel injector assembly

·

Replacement of fuel pump assembly (for high pressure side)

·

Replacement of spark plug

·

Replacement of ignition coil assembly

·

Replacement of EGR valve assembly

·

Replacement of knock control sensor

·

Replacement of air fuel ratio sensor (sensor 2)


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


w/ Canister Pump Module:
(Click here)
w/o Canister Pump Module:
(Click here)
Replacement of automatic transaxle assembly
for UB80E:
·

Reset memory

·

Input transaxle compensation code into ECM

·

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


for Initialization:
(Click here)
for Registration:
(Click here)
for UB80F:
·

Reset memory

·

Input transaxle compensation code into ECM

·

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


for Initialization:
(Click here)
for Registration:
(Click here)
Automatic transaxle fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly for UB60E:
(Click here)
for UB60F:
(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (for Gasoline model) (Click here)
Television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic view monitor system (for Gasoline model) (Click here)
Front wheel alignment adjustment
1.

Perform reset memory

2.

Perform acceleration sensor zero point calibration and store system information memorization.


·

VSC is disabled or malfunctions

·

DTCs are output

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)
Front bumper assembly (Including removal and installation)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (for Gasoline model) (Click here)
Front television camera view adjustment Panoramic view monitor system (for Gasoline model) (Click here)

NOTICE:
·

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.

·

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



PROCEDURE

Hide 1.INSTALL ENGINE ASSEMBLY TO ENGINE STAND

Hide 16361A 3.REMOVE V-RIBBED BELT

Hide 88310 5.REMOVE COMPRESSOR ASSEMBLY WITH PULLEY

Hide 16620D 7.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

Hide 11336A 8.REMOVE TIMING GEAR COVER INSULATOR

Hide 11323C 9.REMOVE NO. 3 TIMING CHAIN COVER

Hide 16207 10.REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 16260 11.REMOVE FLOW SHUTTING VALVE (WATER BY-PASS HOSE ASSEMBLY)

Hide 17167 12.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 22030 15.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 25680 16.REMOVE EGR COOLER ASSEMBLY

Hide 25687 17.REMOVE NO. 1 EGR COOLER BRACKET

Hide 25601 18.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY

Hide 16279 21.REMOVE NO. 3 WATER BY-PASS PIPE

Hide 16278 22.REMOVE NO. 2 WATER BY-PASS PIPE

Hide 17177 24.REMOVE NO. 1 INTAKE MANIFOLD TO HEAD GASKET

Hide 23901 25.DISCONNECT FUEL TUBE SUB-ASSEMBLY

Hide 23801P 26.REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY

Hide 23100X 27.REMOVE FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY (for High Pressure)

Hide 16295 28.REMOVE NO. 7 WATER BY-PASS HOSE

Hide 23807 29.REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

Hide 23807V 30.REMOVE NO. 1 DELIVERY PIPE SPACER

Hide 23291 31.REMOVE INJECTOR VIBRATION INSULATOR

Hide 23250F 33.REMOVE PORT FUEL INJECTOR ASSEMBLY

Hide 23250E 35.REMOVE DIRECT FUEL INJECTOR ASSEMBLY

Hide 11452 38.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 15250 40.REMOVE OIL PRESSURE CONTROL VALVE ASSEMBLY

Hide 11102A 41.REMOVE CAMSHAFT POSITION SENSOR (for Intake Side)

Hide 11102A 42.REMOVE CAMSHAFT POSITION SENSOR (for Exhaust Side)

Hide 15370 43.REMOVE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY

Hide 13090D 44.REMOVE CAM TIMING CONTROL MOTOR WITH EDU ASSEMBLY

Hide 45.DISCONNECT NO. 1 WATER BY-PASS HOSE (w/ Oil Cooler)

a.
A411195

Slide the clip and disconnect the No. 1 water by-pass hose from the cylinder block sub-assembly.


Hide 16264D 46.DISCONNECT NO. 2 WATER BY-PASS HOSE (w/ Oil Cooler)

a.
A411196

Slide the clip and disconnect the No. 2 water by-pass hose from the water by-pass pipe sub-assembly.


Hide 29300 47.REMOVE VACUUM PUMP ASSEMBLY

Hide 13470 48.REMOVE CRANKSHAFT PULLEY ASSEMBLY

Hide 16305E 50.REMOVE OUTLET WATER BY-PASS SUB-ASSEMBLY

Hide 11201 51.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 11193 52.REMOVE SPARK PLUG TUBE GASKET

Hide 12315A 53.REMOVE ENGINE MOUNTING BRACKET RH

Hide 11320B 54.REMOVE NO. 2 TIMING CHAIN COVER ASSEMBLY

Hide 11301C 55.REMOVE TIMING CHAIN COVER OIL SEAL

Hide 56.SET NO. 1 CYLINDER TO TDC (COMPRESSION)

Hide 13507A 57.REMOVE OIL PUMP DRIVE CHAIN SUB-ASSEMBLY

Hide 13050 58.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

Hide 13540 60.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 13559 61.REMOVE CHAIN TENSIONER SLIPPER

Hide 13561 62.REMOVE NO. 1 CHAIN VIBRATION DAMPER

Hide 13070A 63.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

Hide 11310 64.REMOVE TIMING CHAIN COVER ASSEMBLY

Hide 23477 65.REMOVE FUEL PUMP LIFTER GUIDE

Hide 11103 66.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY

Hide 13801 70.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Hide 13750 71.REMOVE VALVE LASH ADJUSTER ASSEMBLY

Hide 11101 73.REMOVE CYLINDER HEAD SUB-ASSEMBLY

Hide 11115 74.REMOVE CYLINDER HEAD GASKET

A403803

a.

Remove the cylinder head gasket from the cylinder block sub-assembly.


Hide 11101A 75.INSPECT CYLINDER HEAD SET BOLT

Hide 11101 76.INSPECT CYLINDER HEAD SUB-ASSEMBLY