Home › Engine / Hybrid System › M20A-FKS (ENGINE MECHANICAL) › ENGINE UNIT › from 2020.08
RM3620E _51 Engine / Hybrid System _076500 M20A-FKS ENGINE MECHANICAL _0372438 ENGINE UNIT A

M20A-FKS ENGINE MECHANICAL  ENGINE UNIT  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during engine unit removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When performing learning using the GTS.

Click here(Click here)

*2: w/ Gasoline Particulate Filter

Battery terminal is disconnected/reconnected Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system (Click here)
Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline model)*1
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)
Reset back door close position Power back door system (for Gasoline model) (Click here)
Power back door initialization Power door lock control system (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration DTC P063051 is output (Click here)
ECU communication ID registration Engine start function See Service Bulletin for the registration method.
for M20A-FKS:

GPF Deposition Values*2

-

GPF deposition values save

-

GPF deposition values write



·

MIL comes on

·

Deterioration of fuel efficiency


(Click here)
for K120:
·

Perform reset memory

·

Perform road test to allow TCM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


(Click here)
for K120F:
·

Perform reset memory

·

Perform road test to allow TCM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


(Click here)
·

Throttle body with motor assembly

·

Cam timing control motor with EDU assembly (Including removal and installation)

·

Camshaft timing gear assembly (Including removal and installation)

·

Cylinder head sub-assembly

·

Camshaft (for intake or exhaust camshaft)

·

Camshaft timing exhaust gear assembly

·

Piston or piston ring

·

Mass air flow meter sub-assembly

·

Port fuel injector assembly

·

Direct fuel injector assembly

·

Fuel pump (for low pressure side)

·

Fuel pump assembly (for high pressure side)

·

Fuel pressure sensor (for low pressure side)

·

Fuel pressure sensor (for high pressure side)

·

Air fuel ratio sensor (sensor 1)

·

Air fuel ratio sensor (sensor 2)

·

Engine coolant temperature sensor

·

Spark plug

·

Ignition coil assembly

·

EGR valve assembly

·

Air intake system parts

·

Gas leaks from exhaust system

·

Knock control sensor


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of continuously variable transaxle assembly Air bleed oil pump with motor assembly Stop and start system (Click here)
for K120, K120F:
·

Input transaxle compensation code into TCM

·

Perform reset memory

·

Deceleration sensor zero point calibration

·

CVT oil pressure calibration

·

Perform road test to allow TCM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


for K120:(Click here)
for K120F:(Click here)
Suspension, tires, etc.
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (for Gasoline model) (Click here)
Television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic view monitor system (for Gasoline model) (Click here)
Front wheel alignment adjustment
1.

Perform reset memory

2.

Perform acceleration sensor zero point calibration and store system information memorization.


·

VSC is disabled or malfunctions

·

DTCs are output

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)
Front bumper assembly (Including removal and installation)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (for Gasoline model) (Click here)
Front television camera view adjustment Panoramic view monitor system (for Gasoline model) (Click here)

NOTICE:
·

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.

·

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



PROCEDURE

Hide 43457 1.REMOVE DRIVE SHAFT BEARING BRACKET

a.
A429161C01
0.042,0.031 0.281,0.292 0.24,0.26 10 true *A 0.031,2.344 0.26,2.573 0.229,0.229 10 true *B
*A for 2WD
*B for 4WD/AWD


Remove the 3 bolts and drive shaft bearing bracket.


Hide 16361A 2.REMOVE V-RIBBED BELT

Hide 88310 4.REMOVE COMPRESSOR WITH PULLEY ASSEMBLY

Hide 16620D 5.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

NOTICE:
A409240

·

Do not apply or add any oil or grease to the belt tensioner to prevent abnormal noises from the belt tensioner pulley, belt squealing, etc.

·

Do not allow oil or grease to adhere to the moving parts of the belt tensioner, as this may cause malfunctions.



a.
A433280

Remove the 2 bolts and V-ribbed belt tensioner assembly from the No. 2 timing chain cover assembly.


Hide 16572D 6.DISCONNECT NO. 2 RADIATOR HOSE

A433281

a.

Slide the clip and disconnect the No. 2 radiator hose from the water inlet.


Hide 16207 7.REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

a.
A433282

Slide the clip and disconnect the No. 2 water by-pass pipe sub-assembly from the outlet water by-pass sub-assembly.


b.

Remove the bolt and No. 2 water by-pass pipe sub-assembly from the water hose clamp bracket.


Hide 16260 8.REMOVE FLOW SHUTTING VALVE (WATER BY-PASS HOSE ASSEMBLY)

a.

for Manual Transaxle:

i.
A433285

Remove the bolt to disconnect the flow shutting valve (water by-pass hose assembly) from the water hose clamp bracket.


ii.

Slide the clip and disconnect the flow shutting valve (water by-pass hose assembly) from the outlet water by-pass sub-assembly.

HINT:

Use a container to catch any engine coolant which flows out of the flow shutting valve (water by-pass hose assembly) and outlet water by-pass sub-assembly.




b.

for CVT:

i.
A433283

Remove the bolt to disconnect the flow shutting valve (water by-pass hose assembly) from the water hose clamp bracket.


ii.

Slide the clip and disconnect the flow shutting valve (water by-pass hose assembly) from the No. 1 water by-pass pipe sub-assembly.

HINT:

Use a container to catch any engine coolant which flows out of the flow shutting valve (water by-pass hose assembly) and outlet water by-pass sub-assembly.




Hide 16278B 9.REMOVE WATER HOSE CLAMP BRACKET

a.
A433287

Remove the 2 bolts and water hose clamp bracket.


Hide 22030 10.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 25680 11.REMOVE EGR COOLER ASSEMBLY

Hide 25601 12.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY

Hide 25620 13.REMOVE EGR VALVE ASSEMBLY

Hide 16279 14.REMOVE NO. 3 WATER BY-PASS PIPE

a.
A425014

Remove the bolt and No. 3 water by-pass pipe from the intake manifold.


b.

Slide the clip and disconnect the No. 3 water by-pass pipe from the water outlet.


Hide 17138B 15.REMOVE INTAKE MANIFOLD STAY

Hide 17177 17.REMOVE NO. 1 INTAKE MANIFOLD TO HEAD GASKET

Hide 23910A 18.DISCONNECT FUEL TUBE SUB-ASSEMBLY

a.
A457661

Remove the fuel tube sub-assembly from the fuel pump assembly.

Click hereEngine / Hybrid System>M20A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION


b.
A457662

Remove the fuel pipe clamp from the fuel tube connector.


c.
A457663

Remove the fuel tube sub-assembly from the fuel delivery pipe with sensor assembly.

Click hereEngine / Hybrid System>M20A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 23801P 19.REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY

a.
A425015

Remove the bolt.


b.

Using a 17 mm union nut wrench, loosen the 2 union nuts of the No. 1 fuel pipe sub-assembly.


Hide 23100X 20.REMOVE FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY (for High Pressure)

Hide 16260 21.REMOVE WATER BY-PASS HOSE ASSEMBLY

a.
A425017

Remove the bolt.


b.

Slide the 2 clips and remove the water by-pass hose assembly from the water inlet with thermostat sub-assembly and cylinder head sub-assembly.


Hide 82219A 22.REMOVE SENSOR WIRE

a.
A425179

Disconnect the 4 connectors.


b.

Detach the 3 clamps.


c.

Remove the bolt and sensor wire from the water inlet with thermostat sub-assembly.


Hide 82126A 23.REMOVE NO. 6 ENGINE WIRE

a.
A425181

Disconnect the 4 connectors.


b.

Detach the 2 clamps.


c.

Remove the 2 nuts and No. 6 engine wire from the wire harness clamp bracket.


Hide 23807 24.REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

Hide 23291 26.REMOVE INJECTOR VIBRATION INSULATOR

Hide 23250F 28.REMOVE PORT FUEL INJECTOR ASSEMBLY

Hide 23250F 30.REMOVE DIRECT FUEL INJECTOR ASSEMBLY

Hide 11452 33.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

a.

Remove the engine oil level dipstick.


b.
A425020

Remove the bolt and engine oil level dipstick guide from the cylinder head sub-assembly.


c.
A425021

Remove the O-ring from the engine oil level dipstick guide.


Hide 16031 34.REMOVE WATER INLET WITH THERMOSTAT SUB-ASSEMBLY

Hide 16032 35.REMOVE ENGINE WATER PUMP ASSEMBLY (WATER INLET HOUSING)

a.
A400319

Remove the 4 bolts, engine water pump assembly (water inlet housing) and gasket from the cylinder block sub-assembly.


Hide 17169A 36.REMOVE NO. 3 EXHAUST MANIFOLD HEAT INSULATOR

a.
A425022

Remove the 2 bolts and No. 3 exhaust manifold heat insulator from the cylinder block sub-assembly.


Hide 25759A 38.REMOVE VACUUM SURGE TANK BRACKET

a.
A457664

Remove the 2 bolts and vacuum surge tank bracket from the camshaft housing sub-assembly.


Hide 12262 39.REMOVE NO. 2 PCV HOSE

a.
A426574

Slide the hose clip and remove the No. 2 PCV hose from the cylinder head cover sub-assembly.


Hide 40.REMOVE WIRE HARNESS CLAMP BRACKET

a.
A401310

Remove the 2 bolts and wire harness clamp bracket from the No. 1 ventilation case.


b.
A426577

Remove the bolt and wire harness clamp bracket from the camshaft housing sub-assembly.


c.
A426579

Remove the bolt and wire harness clamp bracket from the stiffening crankcase assembly.