DTC P0136 Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 2) |
DTC P0137 Oxygen Sensor Circuit Low Voltage (Bank 1 Sensor 2) |
DTC P0138 Oxygen Sensor Circuit High Voltage (Bank 1 Sensor 2) |
DTC P0139 Oxygen Sensor Circuit Slow Response (Bank 1 Sensor 2) |
DTC P0156 Oxygen Sensor Circuit Malfunction (Bank 2 Sensor 2) |
DTC P0157 Oxygen Sensor Circuit Low Voltage (Bank 2 Sensor 2) |
DTC P0158 Oxygen Sensor Circuit High Voltage (Bank 2 Sensor 2) |
DTC P0159 Oxygen Sensor Circuit Slow Response (Bank 2 Sensor 2) |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0136 P0156 |
|
|
| P0137 P0157 |
|
|
| P0138 P0158 |
|
|
| P0139 P0159 | Heated oxygen sensor (sensor 2) voltage does not drop to below 0.2 V immediately after fuel cut starts |
|
| DTC No. | DTC Detection Condition | Trouble Area |
| P0136 P0156 | Not applicable | None |
| P0137 P0157 |
|
|
| P0138 P0158 | Not applicable | None |
| P0139 P0159 | Not applicable | None |


![]() |
| Related DTCs | P0136: Heated oxygen sensor output voltage (Output voltage) (bank 1) P0136: Heated oxygen sensor impedance (Low) (bank 1) P0137: Heated oxygen sensor output voltage (Low voltage) (bank 1) P0137: Heated oxygen sensor impedance (High) (bank 1) P0138: Heated oxygen sensor output voltage (High voltage) (bank 1) P0138: Heated oxygen sensor output voltage (Extremely high) (bank 1) P0139: Heated oxygen sensor output voltage during fuel cut (bank 1) P0156: Heated oxygen sensor output voltage (Output voltage) (bank 2) P0156: Heated oxygen sensor impedance (Low) (bank 2) P0157: Heated oxygen sensor output voltage (Low voltage) (bank 2) P0157: Heated oxygen sensor impedance (High) (bank 2) P0158: Heated oxygen sensor output voltage (High voltage) (bank 2) P0158: Heated oxygen sensor impedance (Extremely high) (bank 2) P0159: Heated oxygen sensor output voltage during fuel cut (bank 2) |
| Required Sensors / Components (Main) | Heated oxygen sensor |
| Required Sensors / Components (Related) | Crankshaft position sensor, engine coolant temperature sensor, mass air flow meter and throttle position sensor |
| Frequency of Operation | Once per driving cycle: Active air-fuel ratio control detection, Abnormal voltage during fuel cut Continuous: Others |
| Duration | 20 seconds: Heated oxygen sensor output (Output voltage, High voltage, Low voltage) 30 seconds: Heated oxygen sensor impedance (Low) 90 second.: Heated oxygen sensor impedance (High) 10 seconds: Heated oxygen sensor impedance (Extremely high) 7 seconds: Heated oxygen sensor voltage during fuel cut |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| The monitor will run whenever these DTCs are not present | P0016, P0018 (VVT system bank 1, 2 - misalignment) P0017, P0019 (Exhaust VVT system bank 1, 2 - misalignment) P0031, P0032, P0051, P0052 (A/F sensor heater) P0037, P0038, P0057, P0058 (HO2 sensor heater) P0100, P0102, P0103 (MAF meter) P0110, P0112, P0113 (IAT sensor) P0115, P0117, P0118 (ECT sensor) P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (TP sensor) P0125 (Insufficient ECT for closed loop) P0128 (Thermostat) P0171, P0172, P0174, P0175 (Fuel system) P0301, P0302, P0303, P0304, P0305, P0306 (Misfire) P0335 (CKP sensor) P0450, P0451, P0452, P0453 (EVAP system) P0500 (Vehicle speed sensor) P2195, P2196, P2197, P2198 (A/F sensor - rationality) P2237, P2240 (A/F sensor - open) P2238, P2241, P2252, P2255 (A/F sensor - low impedance) P2239, P2242, P2253, P2256 (A/F sensor - high impedance) P2A00, P2A03 (A/F sensor - slow response) |
| Active air-fuel ratio control | Performing |
| Active air-fuel ratio control is performed when the following conditions are met: | - |
| Battery voltage | 11 V or more |
| Engine coolant temperature | 75°C (167°F) or more |
| Idle | OFF |
| Engine RPM | Less than 3200 rpm |
| A/F sensor status | Activated |
| Fuel system status | Closed loop |
| Fuel-cut | OFF |
| Engine load | 10 to 70% |
| Shift position | 4th or more |
| Battery voltage | 11 V or more |
| Estimated HO2S temperature | Less than 700°C (1292°F) |
| ECM monitor | Completed |
| DTC P0606 | Not set |
| Battery voltage | 11 V or more |
| Estimated HO2S temperature | 450°C (842°F) or more |
| DTC P0606 | Not set |
| Battery voltage | 11 V or more |
| Time after engine start | 2 seconds or more |
| Engine coolant temperature | 75°C (167°F) or higher |
| Estimated catalyst temperature | 400°C (752°F) or higher |
| Fuel cut | ON |
| Either of the following conditions is met: | 1 or 2 |
| 1. All of the following conditions (a), (b) and (c) are met | - |
| (a) Commanded air-fuel ratio | 14.3 or less |
| (b) Rear HO2 sensor voltage | 0.21 to 0.59 V |
| (c) OSC (Oxygen Storage Capacity of Catalyst) | 2.0 g (0.0044 lb) or more |
| 2. All of the following conditions (d), (f) and (g) are met. | - |
| (d) Commanded air-fuel ratio | 14.9 or more |
| (f) Rear HO2 sensor voltage | 0.21 to 0.59 V |
| (g) OSC | 2.0 g (0.0044 lb) or more |
| All of the following conditions (a), (b) and (c) are met. | - |
| (a) Commanded air-fuel ratio | 14.3 or less |
| (b) Rear HO2 sensor voltage | Less than 0.21 V |
| (c) OSC (Oxygen Storage Capacity of Catalyst) | 2.0 g (0.0044 lb) or more |
| All of the following conditions (a), (b) and (c) are met. | - |
| (a) Commanded air-fuel ratio | 14.9 or more |
| (b) Rear HO2 sensor voltage | More than 0.59 V |
| (c) OSC (Oxygen Storage Capacity of Catalyst) | 2.0 g (0.0044 lb) or more |
| Duration that following condition is met | 30 seconds or more |
| Rear heated oxygen sensor impedance | Less than 5 Ω |
| Duration that following condition is met | 90 seconds or more |
| Rear heated oxygen sensor impedance | 15 kΩ or more |
| Duration that following condition is met | 10 seconds or more |
| Rear heated oxygen sensor voltage | 1.2 V or more |
| Duration until rear heated oxygen sensor voltage drops to 0.2 V during fuel cut | 10 seconds or more |
| Duration that following condition is met | 30 seconds or more |
| Heated oxygen sensor voltage | Varies between 0.1 and 0.9 V |


| Tester Display (Sensor) | Injection Volumes | Status | Voltages |
| AFS B1S1 or AFS B2S1 (A/F) | +25% | Rich | Less than 3.1 |
| AFS B1S1 or AFS B2S1 (A/F) | -12.5% | Lean | More than 3.5 |
| O2S B1S2 or O2S B2S2 (HO2) | +25% | Rich | More than 0.55 |
| O2S B1S2 or O2S B2S2 (HO2) | -12.5% | Lean | Less than 0.4 |
| Case | A/F Sensor (Sensor 1) Output Voltage | HO2 Sensor (Sensor 2) Output Voltage | Main Suspected Trouble Area |
| 1 | ![]() | ![]() | - |
| 2 | ![]() | ![]() |
|
| 3 | ![]() | ![]() |
|
| 4 | ![]() | ![]() |
|
| 1.READ DTC OUTPUT |
Connect the Techstream to the DLC3.
Turn the ignition switch to the ON position and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / Trouble Code.
Read the DTCs.
| Display (DTC Output) | Proceed to |
| P0138 or P0158 | A |
| P0137 or P0157 | B |
| P0136 or P0156 | C |
| P0139 or P0159 | D |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 2.READ VALUE USING TECHSTREAM (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR) |
Connect the Techstream to the DLC3.
Turn the ignition switch to the ON position and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / Data List / A/F Control System / O2S B1 S2 or O2S B2 S2.
Allow the engine to idle.
Read the Heated Oxygen (HO2) sensor output voltage while idling.
| HO2 Sensor Output Voltages | Proceed to |
| Higher than 1.0 V | A |
| Below 1.0 V | B |
|
| ||||
| A | |
| 3.INSPECT HEATED OXYGEN SENSOR (CHECK FOR SHORT) |
![]() |
Disconnect the H14 heated oxygen sensor connector (Bank 1 Sensor 2) or H9 heated oxygen sensor connector (Bank 2 Sensor 2).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| +B (2) - E1 (4) | 10 kΩ or higher |
| +B (2) - OX (3) | 10 kΩ or higher |
| Tester Connections | Specified Condition |
| +B (2) - E1 (4) | 10 kΩ or higher |
| +B (2) - OX (3) | 10 kΩ or higher |
Reconnect the HO2 sensor connectors.
| Result | Proceed to |
| OK | A |
| NG (for 2WD model) | B |
| NG (for 4WD model) | C |
|
| ||||
|
| ||||
| A | |
| 4.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT) |
![]() |
Turn the ignition switch off and wait for 5 minutes.
Disconnect the E9 or E10 ECM connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| HT1B (E9-1) - OX1B (E9-18) | 10 kΩ or higher |
| HT2B (E10-5) - OX2B (E10-33) | 10 kΩ or higher |
Reconnect the ECM connectors.
|
| ||||
| OK | ||
| ||
| 5.CHECK AIR FUEL RATIO SENSOR |
Connect the Techstream to the DLC3.
Turn the ignition switch to the ON position and turn the tester on.
Enter the following menu items: Powertrain / Engine and ECT / Monitor / O2 Sensor / Details.
Check that RANGE B1S1 and RANGE B2S1 are either Pass or Fail.
If the tester shows Incomplete, re-check RANGE B1S1 and RANGE B2S1 after performing the drive pattern as listed below.
Select RANGE B1S1 or RANGE B2S1.
Read the value.
Perform the drive pattern as listed below.

Warm-up the engine until the engine coolant temperature is 75°C (167°F) or more.
Drive the vehicle at 40 mph (64 km/h) or more and decelerate the vehicle for 5 seconds or more. Perform this 3 times.
If the tester shows Incomplete again, add the vehicle speed and use the second gear to decelerate the vehicle.
|
| ||||
|
| ||||
| 6.READ VALUE USING TECHSTREAM (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR) |
Connect the Techstream to the DLC3.
Turn the ignition switch to the ON position and turn the tester on.
Start the engine.
Select the following menu items: Powertrain / Engine and ECT / Data List / A/F Control System / O2S B1 S2 or O2S B2 S2.
After warming up the engine, run the engine at an engine speed of 2500 rpm for 3 minutes.
Read the output voltage of the HO2 sensor when the engine rpm is suddenly increased.
|
| ||||
| OK | |
| 7.PERFORM ACTIVE TEST USING TECHSTREAM (INJECTION VOLUME) |
Connect the Techstream to the DLC3.
Start the engine and turn the tester on.
Warm up the engine.
Select the following menu items: Powertrain / Engine and ECT / Active Test / Control the Injection Volume.
Change the fuel injection volume using the tester, while monitoring the voltage output of Air-Fuel Ratio (A/F) and HO2 sensors displayed on the tester.
| Tester Display (Sensor) | Voltage Variations | Proceed to |
| AFS B1S1 (A/F) AFS B2S1 (A/F) | Alternates between more and less than 3.3 V | OK |
| AFS B1S1 (A/F) AFS B2S1 (A/F) | Remains at more than 3.3 V | NG |
| AFS B1S1 (A/F) AFS B2S1 (A/F) | Remains at less than 3.3 V | NG |

|
| ||||
| OK | ||
| ||
| 8.INSPECT FOR EXHAUST GAS LEAK |
|
| ||||
| OK | |
| 9.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE) |
![]() |
Disconnect the H14 heated oxygen sensor connector (Bank 1 Sensor 2) or H9 heated oxygen sensor connector (Bank 2 Sensor 2).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| HT (1) - +B (2) | 20°C (68°F) | 11 to 16 Ω |
| HT (1) - E1 (4) | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| HT (1) - +B (2) | 20°C (68°F) | 11 to 16 Ω |
| HT (1) - E1 (4) | Always | 10 kΩ or higher |
Reconnect the HO2 sensor connectors.
|
| ||||
| OK | |
| 10.INSPECT RELAY (EFI RELAY) |
![]() |
Remove the EFI relay from the engine room J/B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| 3 - 5 | 10 kΩ or higher |
| 3 - 5 | Below 1 Ω (when battery voltage applied to terminals 1 and 2) |
Reinstall the relay.
|
| ||||
| OK | |
| 11.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM) |
![]() |
Disconnect the H14 or H9 HO2 sensor connector.
Turn the ignition switch to the ON position.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| +B (H14-2) - Body ground | 9 to 14 V |
| +B (H9-2) - Body ground | 9 to 14 V |
Turn the ignition switch off.
Disconnect the E9 and E10 ECM connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| HT (H14-1) - HT1B (E9-1) | Below 1 Ω |
| OX (H14-3) - OX1B (E9-18) | Below 1 Ω |
| E1 (H14-4) - E2 (E9-28) | Below 1 Ω |
| HT (H9-1) - HT2B (E10-5) | Below 1 Ω |
| OX (H9-3) - OX2B (E10-33) | Below 1 Ω |
| E1 (H9-4) - E2 (E9-28) | Below 1 Ω |
| Tester Connection | Specified Condition |
| HT (H14-1) or HT1B (E9-1) - Body ground | 10 kΩ or higher |
| OX (H14-3) or OX1B (E9-18) - Body ground | 10 kΩ or higher |
| E1 (H14-4) or E2 (E9-28) - Body ground | 10 kΩ or higher |
| HT (H9-1) or HT2B (E10-5) - Body ground | 10 kΩ or higher |
| OX (H9-3) or OX2B (E10-33) - Body ground | 10 kΩ or higher |
| E1 (H9-4) or E2 (E9-28) - Body ground | 10 kΩ or higher |
Reconnect the HO2 sensor connectors.
Reconnect the ECM connectors.

|
| ||||
| OK | |
| 12.REPLACE HEATED OXYGEN SENSOR |
| NEXT | |
| 13.PERFORM CONFIRMATION DRIVING PATTERN |
Connect the Techstream to the DLC3.
Warm-up the engine until the engine coolant temperature is 75°C (167°F) or more.
Drive the vehicle at 40 to 75 mph (64 to 120 km/h) for at 10 minutes.
Drive the vehicle 40 mph (64 km/h) or more and decelerate the vehicle for 5 seconds or more. Perform this 3 times.
Turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / Utility / All Readiness.
Input DTCs: P0136, P0137, P0138, P0156, P0157 and P0158.
Check that DTC MONITOR is NORMAL. If DTC MONITOR is Incomplete, perform the driving pattern increasing the vehicle speed and using the second gear to decelerate the vehicle.

| Result | Proceed to |
| NORMAL (DTC is not output) | A |
| ABNORMAL (DTC P0136, P0137, P0138, P0156, P0157 or P0158 is output) (for 2WD model) | B |
| ABNORMAL (DTC P0136, P0137, P0138, P0156, P0157 or P0158 is output) (for 4WD model) | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 14.REPLACE AIR FUEL RATIO SENSOR |
| NEXT | |
| 15.PERFORM CONFIRMATION DRIVING PATTERN |
Connect the Techstream to the DLC3.
Warm-up the engine until the engine coolant temperature is 75°C (167°F) or more.
Drive the vehicle at 40 to 75 mph (64 to 120 km/h) for at 10 minutes.
Drive the vehicle 40 mph (64 km/h) or more and decelerate the vehicle for 5 seconds or more. Perform this 3 times.
Turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / Utility / All Readiness.
Input DTCs: P0136, P0137, P0138, P0156, P0157 and P0158.
Check that DTC MONITOR is NORMAL. If DTC MONITOR is Incomplete, perform the driving pattern increasing the vehicle speed and using the second gear to decelerate the vehicle.

| Result | Proceed to |
| NORMAL (DTC is not output) | A |
| ABNORMAL (DTC P0136, P0137, P0138, P0156, P0157 or P0158 is output) (for 2WD model) | B |
| ABNORMAL (DTC P0136, P0137, P0138, P0156, P0157 or P0158 is output) (for 4WD model) | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 16.READ VALUE USING TECHSTREAM (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR) |
Connect a Techstream to the DLC3.
Start the engine.
Turn the tester ON.
Select the following menu items: Powertrain / Engine / Data List / A/F Control System / O2S B1 S2 or O2S B2 S2.
After warming up the engine, run the engine at an engine speed of 2500 rpm for 3 minutes.
Engine is idling.
Depress the accelerator pedal quickly until the engine speed reaches 2500 rpm 3 times.
| Result | Proceed To |
| Higher than 1.0 V | A |
| Below 1.0 V | B |
|
| ||||
| A | |
| 17.INSPECT HEATED OXYGEN SENSOR |
![]() |
Disconnect the H14 heated oxygen sensor connector (Bank 1 Sensor 2) or H9 heated oxygen sensor connector (Bank 2 Sensor 2).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| +B (2) - E1 (4) | 10 kΩ or higher |
| +B (2) - OX (3) | 10 kΩ or higher |
| Tester Connections | Specified Condition |
| +B (2) - E1 (4) | 10 kΩ or higher |
| +B (2) - OX (3) | 10 kΩ or higher |
Reconnect the HO2 sensor connectors.
| Result | Proceed to |
| OK | A |
| NG (for 2WD model) | B |
| NG (for 4WD model) | C |
|
| ||||
|
| ||||
| A | |
| 18.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT) |
![]() |
Turn the ignition switch off and wait for 5 minutes.
Disconnect the E9 or E10 ECM connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| HT1B (E9-1) - OX1B (E9-18) | 10 kΩ or higher |
| HT2B (E10-5) - OX2B (E10-33) | 10 kΩ or higher |
Reconnect the ECM connectors.
|
| ||||
| OK | ||
| ||
| 19.READ VALUE USING DTC OUTPUT (DTC P0139 OR P0159 IS OUTPUT AGAIN) |
Connect the Techstream to the DLC3.
Clear the DTC (Click here).
Warm-up the engine until the engine coolant temperature is 75°C (167°F) or more.
Drive the vehicle at 40 to 75 mph (64 to 120 km/h) for at 10 minutes.
Drive the vehicle 40 mph (64 km/h) or more and decelerate the vehicle for 5 seconds or more. Perform this 3 times.
Turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / Utility / All Readiness.
Input DTCs: P0139 and P0159.
Check that DTC MONITOR is NORMAL. If DTC MONITOR is Incomplete, perform the driving pattern increasing the vehicle speed and using the second gear to decelerate the vehicle.

| Display (DTC Output) | Proceed to |
| NORMAL (DTC is not output) | A |
| ABNORMAL (DTC P0139 or P0159 is output) (for 2WD model) | B |
| ABNORMAL (DTC P0139 or P0159 is output) (for 4WD model) | C |
|
| ||||
|
| ||||
| A | ||
| ||