Home › Suspension › REAR SUSPENSION › REAR SUSPENSION MEMBER
RM3650E _53 Suspension _079981 REAR SUSPENSION _0387959 REAR SUSPENSION MEMBER A

REAR SUSPENSION  REAR SUSPENSION MEMBER  INSTALLATION  


PROCEDURE

Hide 51206A 1.INSTALL REAR SUSPENSION MEMBER SUB-ASSEMBLY

HINT:

Perform the operations on the left and right side.


a.
C415912C01
2.833,4.042 3,3.927 false 2.25,3.792 2.448,3.031 true 2.552,3.521 2.719,2.938 true 1.385,4.052 1.656,3.594 true 0.729,4.031 0.865,3.854 true 3.021,3.802 3.24,4 0.219,0.198 10 true *a 1.281,4.063 1.5,4.26 0.219,0.198 10 true *b 0.604,4.052 0.823,4.25 0.219,0.198 10 true *b 2.354,2.802 2.573,3 0.219,0.198 10 true *b 2.646,2.729 2.865,2.927 0.219,0.198 10 true *b
*a Engine Lifter
*b Attachment
V100155

Attachment and Wooden Block Placement Location


Using an engine lifter and 4 attachments or equivalent tools, support the rear suspension member sub-assembly as shown in the illustration.

CAUTION:
·
C415913


·

The rear suspension member sub-assembly is a very heavy component. Make sure that it is supported securely.

·

If the rear suspension member sub-assembly is not securely supported, it may drop, resulting in serious injury.



NOTICE:
·

Use attachments and wooden blocks to keep the rear suspension member sub-assembly level.

·

Keep supporting the rear suspension member sub-assembly until the installation has been completed.




b.

Raise the rear suspension member sub-assembly until there is no clearance between the rear suspension member sub-assembly and vehicle.


c.
C409001

Position rear suspension member rear lower brace LH (3).


d.

Replace E18 (1) bolt and 16 mm bolts (2).


e.

Tighten down 16 mm bolts (2).

Torque:
47 N*m (479 kgf*cm, 35 ft.*lbf)


f.

Using SST, tighten the 16 mm bolt (2) an additional 45°.

SST
09900-WA010  

HINT:
·
C417459C02
2.99,1.271 3.156,1.188 false 2.906,2.094 2.906,1.76 false 0.875,3 1.208,3 false 0.104,0.125 0.417,0.281 0.313,0.156 10 false *a 0.448,0.125 0.76,0.281 0.313,0.156 10 false *b 2.042,0.125 2.354,0.281 0.313,0.156 10 false *c 3.188,1.073 3.427,1.271 0.24,0.198 10 false *d 2.854,2.146 3.167,2.302 0.313,0.156 10 false *b 1.302,2.927 1.615,3.083 0.313,0.156 10 false *c
*a Example
*b Before Tightening
*c After Tightening
*d Magnetic Portion



·

The magnetic portion is used to secure the gauge to the vehicle.

·

After first adjusting the needle of the gauge to 0°, tighten to the specified angle.

·

Perform the work procedure carefully so that the gauge, etc. does not become tilted.




g.

Tighten down E18 bolt (1).

Torque:
108 N*m (1101 kgf*cm, 80 ft.*lbf)


h.
C413574

Position rear lower suspension member stopper LH (3).


i.

Replace 16 mm bolts (1) and E18 bolt (2).


j.

Tighten the 16 mm bolts (1).

Torque:
47 N*m (479 kgf*cm, 35 ft.*lbf)


k.

Using SST, tighten the 16 mm bolt (1) an additional 45°.

SST
09900-WA010  

HINT:
·
C417459C02
2.99,1.271 3.156,1.188 false 2.906,2.094 2.906,1.76 false 0.875,3 1.208,3 false 0.104,0.125 0.417,0.281 0.313,0.156 10 false *a 0.448,0.125 0.76,0.281 0.313,0.156 10 false *b 2.042,0.125 2.354,0.281 0.313,0.156 10 false *c 3.188,1.073 3.427,1.271 0.24,0.198 10 false *d 2.854,2.146 3.167,2.302 0.313,0.156 10 false *b 1.302,2.927 1.615,3.083 0.313,0.156 10 false *c
*a Example
*b Before Tightening
*c After Tightening
*d Magnetic Portion



·

The magnetic portion is used to secure the gauge to the vehicle.

·

After first adjusting the needle of the gauge to 0°, tighten to the specified angle.

·

Perform the work procedure carefully so that the gauge, etc. does not become tilted.




l.

Tighten down E18 bolt (2).

Torque:
108 N*m (1101 kgf*cm, 80 ft.*lbf)


m.
C409002

Attach the cable of the parking brake (1) in the holders (2).


n.

w/ LSD:

i.
C413541

Connect connectors (1) and lock.


ii.

Attach the cable clip (2).


iii.

Connect the ground wire with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


iv.
C415605

Install the rear differential protector (2) with the bolts (1).

Torque:
4.5 N*m (46 kgf*cm, 40 in.*lbf)



Hide 48540 2.INSTALL REAR SHOCK ABSORBER ASSEMBLY LH

a.
C415925C02
1.76,1.375 2.177,1.594 true 1.021,1.958 1.563,1.823 true 2.24,1.51 2.479,1.729 0.24,0.219 10 true *a 0.74,1.865 0.979,2.083 0.24,0.219 10 true *b
*a Wooden Block
*b Jack


Support the rear axle carrier sub-assembly LH with the jack and wooden block.


b.

Lift the rear axle carrier sub-assembly LH with the jack and wooden block to the point where a new E18 bolt can be inserted.


c.

Using an 18 mm deep socket wrench, tighten a new nut.

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)


d.

Using SST and 18 mm deep socket wrench, tighten the nut an additional 90°.

SST
09900-WA010  

HINT:
·
C417459C10
2.99,1.271 3.156,1.188 false 2.906,2.094 2.906,1.76 false 0.875,3 1.208,3 false 0.104,0.125 0.417,0.281 0.313,0.156 10 false *a 0.448,0.125 0.76,0.281 0.313,0.156 10 false *b 2.042,0.125 2.354,0.281 0.313,0.156 10 false *c 3.188,1.073 3.427,1.271 0.24,0.198 10 false *d 2.854,2.146 3.167,2.302 0.313,0.156 10 false *b 1.302,2.927 1.615,3.083 0.313,0.156 10 false *c
*a Example
*b Before Tightening
*c After Tightening
*d Magnetic Portion


The magnetic portion is used to secure the gauge to the vehicle.

·

After first adjusting the needle of the gauge to 0°, tighten to the specified angle.

·

Perform the work procedure carefully so that the gauge, etc. does not become tilted.




e.

Remove the jack and wooden block from under the vehicle.


Hide 48530 3.INSTALL REAR SHOCK ABSORBER ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 4.INSTALL REAR COIL SPRING LH

Hide 5.INSTALL REAR COIL SPRING RH

HINT:

Use the same procedure as for the LH side.


Hide 37100 6.INSTALL PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY

Hide 7.INSTALL REAR DISC BRAKE PAD

Hide 8.INSTALL WIRE HARNESS

a.
C415920

Connect connector (1) and lock.


b.

Route wire harness of the rear height control sensor sub-assembly through brackets (2).


Hide 9.INSTALL REAR FLEXIBLE HOSE LH

a.

Feed rear flexible hose LH into the holder.

NOTICE:

Make sure that the rear flexible hose LH does not rest against the components fixed to the body and that it is not twisted.



Hide 10.INSTALL REAR FLEXIBLE HOSE RH

HINT:

Use the same procedure as for the LH side.


Hide 89516P 11.INSTALL REAR SKID CONTROL SENSOR WIRE LH

a.
C409004

Connect the cable of the rear skid control sensor wire LH in the brackets (1).


b.
C413650

Connect the cable of the rear skid control sensor wire LH in the brackets (1).


c.

Connect connector (2) and lock.


Hide 89516N 12.INSTALL REAR SKID CONTROL SENSOR WIRE RH

HINT:

Use the same procedure as for the LH side.


Hide 65638 13.INSTALL REAR WHEEL HOUSE LINER LH

HINT:

Use the same procedure as for the RH side.


Hide 65637 14.INSTALL REAR WHEEL HOUSE LINER RH

Hide 48738 15.INSTALL REAR SUSPENSION ARM COVER LH

Hide 48737 16.INSTALL REAR SUSPENSION ARM COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 17.INSTALL REAR WHEEL

Hide 18.INSPECT AND ADJUST REAR WHEEL ALIGNMENT