Home › Audio / Visual / Telematics › AUDIO / VIDEO › STEREO COMPONENT AMPLIFIER
RM3650E _56 Audio / Visual / Telematics _079983 AUDIO / VIDEO _0387976 STEREO COMPONENT AMPLIFIER A

AUDIO / VIDEO  STEREO COMPONENT AMPLIFIER  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:
·

Working on 12 V vehicle electrical system.

Risk of short circuits! Risk of fire!

-

Detach battery earth lead from battery.




NOTICE:
·

Electrostatic discharge.

Damage to or destruction of electrical components.

-

Leave electrical components in original packaging until just before they are installed. Use the original packaging only for any return shipments. Always package removed components straight away.

-

Only touch the housings of electrical components. Do not touch pins or multi-pin connectors directly.

-

Antistatic work clothing and antistatic shoes (with ESD symbol).

-

For additional information see:

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



·

Before performing work on electronic components, disconnect the cable from the negative (-) battery terminal to prevent damage to the electrical system or components.

·

When disconnecting the cable, turn the START-STOP button (engine switch) and headlight switch off and loosen the cable nut completely. Perform these operations without twisting or prying on the cable. Then disconnect the cable.

·

Clock settings, radio settings, audio system memory, DTCs and other data will be cleared when the cable is disconnected from the negative (-) battery terminal. Write down any necessary data before disconnecting the cable.



PROCEDURE

Hide 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

·
·

Hide 62480A 2.REMOVE ROOF SIDE INNER GARNISH ASSEMBLY LH

Hide 64288D 3.SEPARATE TRANSVERSE PIPE TRIM

Hide 62609 4.REMOVE SEAT BELT HOLE COVER SUB-ASSEMBLY LH

Hide 81604 5.REMOVE TRIANGLE REFLECTOR SET

Hide 64716D 6.REMOVE DECK TRIM REAR COVER

Hide 81330 7.REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY

Hide 66311 8.REMOVE ROPE HOOK (w/ Courtesy Light)

Hide 64740B 9.REMOVE DECK TRIM SIDE BOARD AND DECK SIDE TRIM COVER LH

Hide 10.REMOVE STEREO COMPONENT AMPLIFIER ASSEMBLY WITH BRACKET

NOTICE:
·

Electrostatic discharge.

Damage to or destruction of electrical components.

-

Leave electrical components in original packaging until just before they are installed. Use the original packaging only for any return shipments. Always package removed components straight away.

-

Only touch the housings of electrical components. Do not touch pins or multi-pin connectors directly.

-

Antistatic work clothing and antistatic shoes (with ESD symbol).

-

For additional information see:

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



·

Damage to wires when disconnecting connectors and plug connections.

Sheared wires can cause a short circuit.

-

Do not pull on the wires when disconnecting connectors and plug connections.



·

Sensitive optical fibers.

Damaged optical fibers can result in operating failure of the LED.

-

Do not bend optical fibers too much and do not kink, as well. The minimum permissible bending radius is 25 mm.

-

Avoid pressure and tensile loads and heat influences on the optical fiber.




a.
E415641

Loosen nuts (1).


b.
E416373

Detach the clamps (1).


c.

Detach the clamp (2) to remove the stereo component amplifier assembly with bracket (3).


d.
E416374

Unlock plug connections (1) and disconnect.


Hide 11.REMOVE STEREO COMPONENT AMPLIFIER ASSEMBLY

a.
E415642

Loosen bolt (1).


b.
E415643C01
0,0 0,0 false
V100136

Remove in this Direction


Detach the guides (2) to remove the stereo component amplifier assembly (1) from the No. 1 amplifier bracket (3) in the direction of the arrow.