Home › Engine / Hybrid System › B58 (INTAKE / EXHAUST) › TURBOCHARGER › 2019.03–2020.03
RM3650E _51 Engine / Hybrid System _080024 B58 INTAKE / EXHAUST _0388138 TURBOCHARGER A

B58 INTAKE / EXHAUST  TURBOCHARGER  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:
·

Hot surfaces.

Risk of burning!

-

Perform all work only on components that have cooled down.




NOTICE:
·

Electrostatic discharge.

Damage to or destruction of electrical components.

-

Only touch the housings of electrical components. Do not touch pins or multi-pin connectors directly.

-

For additional information see:

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION




HINT:
·

Prior to replacing the turbocharger sub-assembly: Observe the notes on troubleshooting on the turbocharger sub-assembly.

Click hereEngine / Hybrid System>B58 (INTAKE / EXHAUST)>EXHAUST SYSTEM>INSPECTION

·

For turbocharger sub-assembly damage: Check the pressure pipes, intercooler and intake manifold for foreign matter, damage and correct functionality.

·

If the outlet turbo oil pipe is exchanged, then the connecting pipe to the oil pan sub-assembly must always be cleaned, as the connecting pipe can coke.



PROCEDURE

Hide 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 2.REMOVE STEERING LINK ASSEMBLY

Hide 17882 4.REMOVE NO. 2 AIR CLEANER HOSE

Hide 7.DRAIN ENGINE COOLANT (for High-Temperature)

Hide 25051 8.REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

Hide 16028 10.DISCONNECT NO. 2 TURBO WATER PIPE SUB-ASSEMBLY

CAUTION:
·

Hot fluids.

Risk of scalding!

-

Conduct all work in the vehicle wearing appropriate personal protective equipment only.




HINT:

Collect and dispose of emerging fluids. Observe country specific waste disposal regulations.


a.
C406325

Unlock and disconnect the coolant hose (1).


b.
C406328

Unscrew the T30 bolt (1) on the holder of the No. 2 turbo water pipe sub-assembly.


Hide 15407 11.DISCONNECT INLET TURBO OIL PIPE SUB-ASSEMBLY

CAUTION:
·

Hot fluids.

Risk of scalding!

-

Conduct all work in the vehicle wearing appropriate personal protective equipment only.




HINT:
·

Have a rag ready and catch any engine oil that may emerge.

·

Make sure no engine oil runs onto fan and generator v belt.



a.
A441891

Loosen the T30 bolt (1).


b.

Remove the inlet turbo oil pipe sub-assembly (2).


Hide 17201 12.REMOVE TURBOCHARGER SUB-ASSEMBLY

CAUTION:
·

Hot surfaces.

Risk of burning!

-

Perform all work only on components that have cooled down.




a.
A441906

Loosen the T30 bolts (1) and (2).


b.

Remove No. 1 turbo water pipe sub-assembly (3) from the cylinder block sub-assembly.


c.
A441907

Unscrew the nuts (1) from the turbocharger sub-assembly (2).


d.
A441908

Unscrew the T40 bolt (1) from the turbocharger sub-assembly (2).


e.
A441909

Remove the turbocharger sub-assembly (1) in the direction of the arrow.

CAUTION:
·

Heavy component.

·

Heavy components can lead to injury or damage.

-

Remove and install heavy components with the aid of another person/other persons.





Hide 16028 13.REMOVE NO. 2 TURBO WATER PIPE SUB-ASSEMBLY

HINT:

Perform this procedure only when replacement of the turbocharger sub-assembly is necessary.


Click hereEngine / Hybrid System>B58 (INTAKE / EXHAUST)>TURBO WATER PIPE (for Outlet Side)>REMOVAL

Hide 15407 14.REMOVE INLET TURBO OIL PIPE SUB-ASSEMBLY

HINT:

Perform this procedure only when replacement of the turbocharger sub-assembly is necessary.


Click hereEngine / Hybrid System>B58 (INTAKE / EXHAUST)>INLET TURBO OIL PIPE>REMOVAL

Hide 16027 15.REMOVE NO. 1 TURBO WATER PIPE SUB-ASSEMBLY

HINT:

Perform this procedure only when replacement of the turbocharger sub-assembly is necessary.


Click hereEngine / Hybrid System>B58 (INTAKE / EXHAUST)>TURBO WATER PIPE (for Inlet Side)>REMOVAL