Home › Engine / Hybrid System › B48 (ENGINE MECHANICAL) › CYLINDER HEAD
RM3650E _51 Engine / Hybrid System _080178 B48 ENGINE MECHANICAL _0388880 CYLINDER HEAD A

B48 ENGINE MECHANICAL  CYLINDER HEAD  REASSEMBLY  


PROCEDURE

Hide 4.INSTALL EXHAUST VALVE COMPRESSION SPRING

Hide 5.INSTALL INTAKE VALVE COMPRESSION SPRING

Hide 13750 6.INSTALL VALVE LASH ADJUSTER ASSEMBLY

Hide 13801 7.INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Hide 13502B 8.INSTALL EXHAUST CAMSHAFT SUB-ASSEMBLY

Hide 13053 9.INSTALL NO. 3 CAMSHAFT SUB-ASSEMBLY

Hide 15330G 10.INSTALL SERVO MOTOR

a.
A441638

Replace O-ring (1).


b.
A441639

Push the O-ring (1) onto the housing to the limit position.


c.
A441208

Insert the servo motor (1) to the gearing.


d.

Using a 4 mm hexagon socket wrench (2), turn the drive shaft of the servo motor (1) in the direction of the arrow until the servo motor (1) is flush with the cylinder head sub-assembly.


e.
A441206

Tighten the T30 bolts (1).

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 13501A 11.INSTALL INTAKE CAMSHAFT SUB-ASSEMBLY

Hide 13801 12.INSPECT NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Hide 13800 13.INSPECT INTERMEDIATE LEVER

Hide 13800 14.INSTALL INTERMEDIATE LEVER

Hide 13908A 15.INSTALL GATE

a.
A441625

Clean contact surfaces (1) and (2) off oil, grease and dirt.


b.
A441310

Position the gate (2) and hand-tighten the bolt (1).


c.

Make sure the intermediate lever is in the correct installation position.


d.
A441379

Position the special tool 2 359 089 on the cylinder head sub-assembly.

SST
09200-WA420  


e.

Pre-tension the gate with the lever (3).


f.

Move bolt (1) against contact surface (2).


g.

Make sure that the special tool 2 359 089 does not rotate during this process.

SST
09200-WA420  


h.
A441220

Secure the gate with the lever (1) in the direction of the arrow.


i.
A441312

Make sure that the special tool 2 359 089 rests flat against the cylinder head (arrows).

SST
09200-WA420  


j.
A441380

Press the special tool 2 359 089 onto the cylinder head in the direction of the arrow.

SST
09200-WA420  


k.

Tighten the bolt (1) at the same time.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


l.

Repeat the step for all the gates.


Hide 16.INSPECT AND ADJUST CAMSHAFT

Hide 17.INSTALL TORSION SPRING

CAUTION:
·

Spring preload.

Danger of injury!

-

The use of the specified special tool (tool) is mandatory.

-

The described operation must be carried out properly.




HINT:

Wear safety goggles.


a.
A441627

Insert the torsion spring (2) in the clamping lever of the special tool 2 359 088.

SST
09200-WA410  


b.

Make sure that the torsion spring (2) is correctly positioned in the marked area (1) of the special tool 2 359 088.

SST
09200-WA410  


c.
A441628

Ensure that the torsion spring (1) lies correctly in the lateral guides (arrows) of the special tool 2 359 088.

SST
09200-WA410  


d.
A441436

Carefully close the clamping lever (2) of the special tool 2 359 088 in the fixture (3) until the retaining hook (1) audibly engages.

SST
09200-WA410  

i.

The torsion spring is tensioned.



e.

Carefully take the clamping lever (2) of the special tool 2 359 088 with the stretched torsion spring out of the fixture (3) of the special tool 2 359 088 in the direction of arrow.

SST
09200-WA410  


f.
A441431

Guide in and position clamping lever (1) of the special tool 2 359 088 on the cylinder head with the clamped torsion spring.

SST
09200-WA410  


g.

Ensure that the clamping lever (1) of the special tool lies flat in the area of the cylinder head sub-assembly.


h.
A441630

Ensure that the torsion spring (2) in the intermediate lever (1) is positioned correctly.


i.

Check the No. 1 valve rocker arm sub-assembly (3) for correct mounting orientation.


j.
A441434

Carefully unlock the retaining hook (2) on the clamping lever (1) of the special tool 2 359 088.

SST
09200-WA410  

i.

The torsion spring tension is relieved.



k.
A441431

Guide out and remove the clamping lever (1) of the special tool 2 359 088.

SST
09200-WA410  


l.
A441632

Check for correct mounting orientation of the torsion spring (arrow) at the cylinder head sub-assembly.


m.

Repeat the operations for the remaining valve spring retainers.


n.
A441429

Guide in the camshaft sensor wheel (3) and install.


o.

Make sure that camshaft sensor wheel (3) is positioned correctly on guide pin (4).


p.

Secure the intake camshaft sub-assembly with a conventional open-end spanner (1).


q.

Tighten down bolt (2).

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)