Home › Engine / Hybrid System › B58 (ENGINE MECHANICAL) › CYLINDER HEAD GASKET › 2019.03–2020.03
RM3650E _51 Engine / Hybrid System _080179 B58 ENGINE MECHANICAL _0388892 CYLINDER HEAD GASKET A

B58 ENGINE MECHANICAL  CYLINDER HEAD GASKET  REMOVAL  


PROCEDURE

Hide 13050 1.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

Hide 13070A 2.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

Hide 3.REMOVE WHEEL ASSEMBLY

Hide 45047 4.DISCONNECT TIE ROD END SUB-ASSEMBLY LH

Hide 45046 5.DISCONNECT TIE ROD END SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 51219 6.REMOVE FRONT SUSPENSION MEMBER LOWER PROTECTOR

Hide 45220 7.REMOVE STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 8.REMOVE STEERING LINK ASSEMBLY

Hide 25051 10.REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

Hide 17293 11.REMOVE TURBOCHARGER STAY

a.
A441294

Loosen T40 bolt (1).


b.

Release T40 bolts (2) and remove the turbocharger stay.


Hide 11101 12.REMOVE CYLINDER HEAD SUB-ASSEMBLY

CAUTION:
·

Heavy component.

Heavy components can lead to injury or damage.

-

Remove and install heavy components with the aid of another person/other persons.




HINT:

Collect and dispose of emerging fluids. Observe country-specific waste disposal regulations.


a.
A441906

Loosen T30 bolts (1) and (2).


b.

Guide the No. 1 turbo water pipe sub-assembly for turbocharger sub-assembly (3) from the cylinder block sub-assembly and place it aside.


c.

Catch and dispose of escaping coolant.


d.
A441889

Release T30 bolt (1) on the holder of No. 2 turbo water pipe sub-assembly (2).


e.

Have a rag ready and catch any engine oil that may emerge.


f.
A441890

Loosen T30 bolt (1).


g.

Guide out No. 2 turbo water pipe sub-assembly and No. 1 turbo water pipe sub-assembly (2) for the turbocharger sub-assembly and place it aside.


h.

Guide out turbo inlet turbo oil pipe sub-assembly (3) for the turbocharger sub-assembly and place it aside.


i.

Collect and dispose of emerging fluids.


j.
A442037

Unlock plug connection (1) and disconnect.


k.
A442032

Unlock and release clamps (1) and (2).


l.

Feed out alternator positive battery cable (3) and put to one side.


m.
A442033

Loosen E8 bolts (1).


n.

Unlock lock (2).


o.

Guide out transmission wire (3) and place it aside.


p.
A442034

Loosen T30 bolts (1).


q.

Guide out the wiring harness section for engine wire (2) and place to one side.


r.
A442035

Loosen T30 bolt (1).


s.

Guide out and remove the No. 4 engine cover (2).


t.
A442251

Unlock and disconnect plug connection (1) on coolant temperature sensor (2).


u.
A442036

Loosen T30 bolts (1).


v.

Feed out No. 2 water by-pass hose (2) and place to one side.


w.
A441442

Release the T45 bearing journal (1) from the No. 1 chain vibration damper (2).


x.
A442038

Loosen E10 bolts (1).


y.

Guide out the chain damper guide (2) and remove.


z.
A441331

Rotate intake camshaft sub-assembly, if necessary in the position shown.

i.

The recess (2) must point upwards.



aa.

Loosen 3 mm hexagon bolt (1).


ab.
A441332

Slide camshaft sensor wheel (1) in the direction of cylinder 1 and guide it out from the intake camshaft sub-assembly.


ac.
A442041

Guide in and position special tool 2 459 012 on cylinder head sub-assembly.

SST
09200-WA610  


ad.

Tighten the bolts (1) of special tool 2 459 012 .

SST
09200-WA610  

Torque:
21.5 N*m (219 kgf*cm, 16 ft.*lbf)


ae.
A442039

Loosen E10 bolts (1) to (5).


af.
A441333

Undo the T60 bolts in the order (14) to (1) .

NOTICE:
A442040

·

Damage to the guide rails.

Large amounts of force may damage the guide rails of the timing chain.

-

Make sure not to damage the guide rail with the cylinder head sub-assembly when removing and installing the cylinder head sub-assembly.





ag.

Lift out cylinder head sub-assembly (1) and the turbocharger sub-assembly with an auxiliary person, the workshop crane and special tool 0 490 567 (11 0 020).

SST
09200-WA860  


Hide 11115 13.REMOVE CYLINDER HEAD GASKET

a.
A442043

Thread out and remove cylinder head gasket (1).


Hide 14. SEALING OIL DUCT

a.
A442045

Seal the oil duct using special tool (B) from the set of special tools 2 364 711 .

SST
09200-WA530  


Hide 15. CLEAN SEALING SURFACE

NOTICE:
·

Damage to the surface.

The use of metal-cutting tools (e.g. emery cloth) to clean the surfaces can damage them and lead to leaks or engine damage.

-

Do not use any metal-cutting tools.




a.
A444847

Remove coarse backlogs from the sealing surfaces of the cylinder head sub-assembly.


b.
A444848

Remove fine backlogs from the sealing surfaces of the cylinder head sub-assembly.


c.
A442047

Clean all blind holes (1) of the cylinder head sub-assembly.


d.
A444849

Remove coarse backlogs from the sealing surfaces of the cylinder block sub-assembly.


e.
A444850

Remove fine backlogs from the sealing surfaces of the cylinder block sub-assembly.

CAUTION:
·

Swirling dirt particles caused by compressed air.

Danger of injury!

-

Collect dirt particles, e.g. when blowing out, use cloth to do so.

-

Wear safety goggles.





f.
A442048

Clean all threaded holes (1) of the cylinder block sub-assembly with compressed air.


g.
A442045

Remove special tool (B) contained in the set of special tools 2 364 711 .

SST
09200-WA530