Home › ENGINE · 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0300    Random / Multiple Cylinder Misfire Detected

DTC    P0301    Cylinder 1 Misfire Detected

DTC    P0302    Cylinder 2 Misfire Detected

DTC    P0303    Cylinder 3 Misfire Detected

DTC    P0304    Cylinder 4 Misfire Detected

DTC    P0305    Cylinder 5 Misfire Detected

DTC    P0306    Cylinder 6 Misfire Detected

for Preparation Click here


DESCRIPTION

A093767E07
When the engine misfires, high concentrations of hydrocarbons (HC) enter the exhaust gas. High HC concentration levels can cause increase in exhaust emission levels. Extremely high concentrations of HC can also cause increases in the Three-Way Catalytic Converter (TWC) temperature, which may cause damage to the TWC. To prevent this increase in emissions and to limit the possibility of thermal damage, the ECM monitors the misfire rate. When the temperature of the TWC reaches the point of thermal degradation, the ECM blinks the MIL. To monitor misfires, the ECM uses both the VVT sensor and the Crankshaft Position (CKP) sensor. The VVT sensor is used to identify any misfiring cylinders and the CKP sensor is used to measure variations in the crankshaft rotation speed. Misfires are counted when the crankshaft rotation speed variations exceed predetermined thresholds. If the misfire count exceeds the threshold levels, the ECM illuminates the MIL and sets a DTC.

DTC Code
DTC Detection Condition
Trouble Area
P0300
Simultaneous misfiring of several cylinders occurs and one of following conditions below is detected (2 trip detection logic):
  1. High temperature misfire occurs in Three-Way Catalytic Converter (TWC) (MIL blinks)
  2. Emission deterioration misfire occurs (MIL illuminates)
  1. Open or short in engine wire harness
  2. Connector connection
  3. Vacuum hose connections
  4. Ignition system
  5. Injector
  6. Fuel pressure
  7. Mass Air Flow (MAF) meter
  8. Engine Coolant Temperature (ECT) sensor
  9. Compression pressure
  10. Valve clearance
  11. Valve timing
  12. PCV valve and hose
  13. PCV hose connections
  14. Air induction system
  15. ECM
P0301
P0302
P0303
P0304
P0305
P0306
Misfiring of specific cylinder occurs and one of following conditions below is detected (2 trip detection logic):
  1. High temperature misfire occurs in Three-Way Catalytic Converter (TWC) (MIL blinks)
  2. Emission deterioration misfire occurs (MIL illuminates)
When multiple DTCs for misfiring cylinders are set, but DTC P0300 is not set, it indicates that misfires have been detected in different cylinders at different times. DTC P0300 is only set when several misfiring cylinders are detected at the same time.

MONITOR DESCRIPTION

The ECM illuminates the MIL and sets a DTC when either one of the following conditions, which could cause emission deterioration, is detected (2 trip detection logic).
  1. Within the first 1000 crankshaft revolutions of the engine starting, an excessive misfiring rate (approximately 20 to 50 misfires per 1000 crankshaft revolutions) occurs once.
  2. An excessive misfiring rate (approximately 20 to 50 misfires per 1,000 crankshaft revolutions) occurs a total of 4 times.
The ECM flashes the MIL and sets a DTC when either one of the following conditions, which could cause the Three-Way Catalytic Converter (TWC) damage, is detected (2 trip detection logic).
  1. At a high engine rpm, a catalyst damage misfire, which monitored every 200 crankshaft revolutions, occurs once.
  2. At a normal engine rpm, a catalyst damage misfire, which monitored every 200 crankshaft revolutions, occurs 3 times.

HINT:
If a catalyst damage misfire occurs, the ECM informs the driver by flashing the MIL.


MONITOR STRATEGY


Related DTCs
P0300: Multiple cylinder misfire
P0301: Cylinder 1 misfire
P0302: Cylinder 2 misfire
P0303: Cylinder 3 misfire
P0304: Cylinder 4 misfire
P0305: Cylinder 5 misfire
P0306: Cylinder 6 misfire
Required Sensors/Components (Main)
Crankshaft position sensor and Camshaft position sensor
Required Sensors/Components (Related)
Engine coolant temperature and intake air temperature sensors and Mass air flow meter
Frequency of Operation
Continuous
Duration
1000 to 4000 crankshaft revolutions: Emission related misfire
200 to 600 crankshaft revolutions: Catalyst damaged misfire
MIL Operation
2 driving cycles: (MIL illuminates when misfire detected)
MIL flashes immediately: When catalyst damaged misfire occur
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Misfire: 
Monitor runs whenever following DTCs not present
P0016, P0018 (VVT System - Misalignment)
P0102, P0103 (Mass Air Flow Sensor)
P0110, P0112, P0113 (Intake Air Temperature Sensor)
P0115, P0117, P0118 (Engine Coolant Temperature Sensor)
P0125 (Insufficient Coolant Temperature for Closed Loop Fuel Control)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle Position Sensor)
P0327, P0328, P0332, P0333 (Knock Sensor)
P0335 (Crankshaft Position Sensor)
P0340 (Camshaft Position Sensor)
P0351 - P0356 (Igniter)
P0500 (Vehicle Speed Sensor)
P0705 (Shift Lever Position Switch)
Battery voltage
8 V or more
VVT system
Not operated by scan tool
Engine RPM
400 to 5400 rpm
Either of following conditions (a) or (b) met
-
(a) ECT at engine start
More than -7°C (19°F)
(b) ECT
More than 20°C (68°F)
Fuel cut
OFF

Monitor period of emission-related-misfire: 
First 1000 revolutions after engine start, or Check Mode
Crankshaft 1000 revolutions
Except above
Crankshaft 1000 revolutions x 4

Monitor period of catalyst-damaged-misfire (MIL blinks): 
All of following conditions 1, 2 and 3 met
Crankshaft 200 revolutions x 3
1. Driving cycles
1st
2. Check mode
OFF
3. Engine RPM
Less than 2800 rpm
Except above
Crankshaft 200 revolutions

TYPICAL MALFUNCTION THRESHOLDS


Monitor period of emission-related-misfire: 
Misfire rate
2% or more

Monitor period of catalyst-damaged-misfire (MIL blinks): 
Number of misfire per 200 revolutions
98 or more (varies with intake air amount and RPM)
Paired cylinder misfire (MIL blinks immediately)
Detected

MONITOR RESULT

Refer to CHECKING MONITOR STATUS (Click here).

WIRING DIAGRAM

Wiring diagram of the ignition system.

A160534E01


A160533E01


CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch ON.
  3. Turn the Techstream ON.
  4. Record the DTC(s) and freeze frame data.
  5. Using the Techstream, switch the ECM from normal mode to check mode (Click here).
  6. Read the misfire counts of each cylinder (Cylinder #1 Misfire Rate to Cylinder #6 Misfire Rate) with the engine in an idling condition. If any misfire count is displayed, skip the following confirmation driving pattern.
  7. Drive the vehicle several times with the conditions, such as engine rpm and engine load, shown in Misfire RPM and Misfire Load in the Data List.

    HINT:
    1. In order to store misfire DTCs, it is necessary to operate the vehicle for the period of time shown in the table below, using the Misfire RPM and Misfire Load in the Data List.

    Engine RPM
    Duration
    Idling
    3.5 minutes or more
    1000
    3 minutes or more
    2000
    1.5 minutes or more
    3000
    1 minute or more

  8. Check whether misfires have occurred by checking DTCs and freeze frame data.

    HINT:
    Do not turn the ignition switch OFF until the stored DTC(s) and freeze frame data have been recorded. When the ECM returns to normal mode (default), the stored DTC(s), freeze frame data and other data will be erased.

  9. Record the DTC(s), freeze frame data and misfire counts.
  10. Turn the ignition switch OFF and wait for at least 5 seconds.

INSPECTION PROCEDURE

HINT:
  1. If any DTCs other than misfire DTCs are output, troubleshoot those DTCs first.
  2. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  3. If the misfire does not recur when the vehicle is brought to the workshop, reproduce the conditions stored in the ECM as freeze frame data.
  4. If the misfire still cannot be reproduced even though the conditions stored in the ECM as freeze frame data have been reproduced, one of the following factors is considered to be a possible cause of the problem:
    1. There was insufficient fuel volume in the tank.
    2. Improper fuel is used.
    3. The spark plugs have been contaminated.
  5. After finishing repairs, check the misfire counts of the cylinders (Cylinder #1 Misfire Rate to Cylinder #6 Misfire Rate).
  6. Be sure to confirm that no misfiring cylinder DTCs are set again by conducting the confirmation driving pattern after finishing repairs.
  7. For 6 and 8 cylinder engines, the ECM intentionally does not set the specific misfiring cylinder DTCs at high engine RPM. If misfires occur only in high engine RPM areas, only DTC P0300 is set.
    In the event of DTC P0300 being present, perform the following operations:
    1. Clear the DTC (Click here).
    2. Start the engine and conduct the confirmation driving pattern.
    3. Read the misfiring rates of each cylinder or DTC(s) using the Techstream.
    4. Repair the cylinder(s) that has a high misfiring rate or is indicated by the DTC.
    5. After finishing repairs, conduct the confirmation driving pattern again, in order to verify that DTC P0300 is not set.
  8. When one of Short FT #1, Long FT #1, Short FT #2 or Long FT #2 in the freeze frame data is outside the range of +/-20%, the air-fuel ratio may be Rich (-20% or less) or Lean (+20% or more).
  9. When the Coolant Temp in the freeze frame data is less than 75°C (167°F), the misfire have occurred only while warming up the engine.
  10. An extremely imbalanced drive wheel can cause body vibration, which may cause misfire DTC(s) to be stored.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO MISFIRE CODES)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch ON.

  1. Turn the Techstream ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.

    HINT:
    Write down the DTCs.


    Result:

    Display (DTC Output)
    Proceed to
    P0300, P0301, P0302, P0303, P0304, P0305 and/or P0306
    A
    P0300, P0301, P0302, P0303, P0304, P0305 and/or P0306 and other DTCs
    B

HINT:
If any DTCs other than P0300, P0301, P0302, P0303, P0304, P0305 and P0306 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.READ VALUE USING TECHSTREAM (MISFIRE RPM AND MISFIRE LOAD)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch ON and turn the Techstream ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Misfire / Misfire RPM and Misfire Load.

  1. Read and note the Misfire RPM and Misfire Load values.

    HINT:
    The Misfire RPM and Misfire Load values indicate the vehicle conditions under which the misfire occurred.


NEXT


3.CHECK PCV HOSE CONNECTIONS

OK:
PCV hose is correctly connected and is not damaged.



NG
REPAIR OR REPLACE PCV HOSE
OK


4.READ VALUE USING TECHSTREAM
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch ON and turn the Techstream ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Catalyst OT MF F/C.

  1. Read the value displayed on the Techstream.

    Result:
    Data List
    Tester Display
    Proceed to
    CAT OT MF F/C (Catalyst OT MF F/C)
    AVAIL (Avail)
    A
    NOT AVL (Not Avl)
    B



B
Go to step 6
A


5.PERFORM ACTIVE TEST USING TECHSTREAM
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch ON and turn the Techstream ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Prohibit the Catalyst OT Misfire prevent F/C.

  1. Perform the Active Test.

    NOTICE:
    When performing the Active Test, make sure the vehicle is stopped and either idling or being revved within 3000 rpm.


NEXT


6.READ VALUE USING TECHSTREAM
  1. (a) Enter the following menus: Powertrain / Engine and ECT / Data List / Misfire / Cylinder #1 Misfire Rate, #2, #3, #4, #5 and #6.
  2. (b) Read each value for Cylinder #1 Misfire Rate to #6 displayed on the Techstream. If no misfire counts occur in any cylinders, perform the following procedures:
    1. (1) Start the engine and let it idle.
    2. (2) Move the shift lever to the D position.
    3. (3) Check the Cylinder #1 Misfire Rate to #6.
    4. (4) If misfire counts are still not displayed, perform steps (c) and (d).
  3. (c) Drive the vehicle with the Misfire RPM and Misfire Load noted in the "Read value using Techstream (Misfire RPM and Misfire Load)" procedures above.
  4. (d) Read the Cylinder #1 Misfire Rate to #6 or DTCs displayed on the Techstream.

    Result:

    Misfire Count
    Proceed to
    Most misfires occur in only 1 or 2 cylinders
    A
    3 cylinders or more have equal misfire counts
    B

    HINT:
    1. If it is difficult to reproduce misfires for each cylinder, check the Data List item called Misfire Margin. Try to find vehicle driving conditions that lower the Misfire Margin value. Values above 30% are considered normal.
    2. If the freeze frame data's record of the ECT is below 75°C (167°F), the misfire may be detected only when the engine is cold.
    3. If the freeze frame data's record of the Engine Run Time is below 120 seconds, the misfire may be detected immediately after the engine is started.



B
Go to step 19
A


7.CHECK SPARK PLUG
  1. Remove the ignition coil and the spark plug of the misfiring cylinder (Click here).

  1. Measure the spark plug electrode gap .



NG
REPLACE SPARK PLUG
OK


8.CHECK FOR SPARKS AND IGNITION
  1. Disconnect the injector connectors to prevent the engine from starting.

    CAUTION:
    Always disconnect all injector connectors.

    NOTICE:
    Do not crank the engine for more than 2 seconds.

  1. Remove the ignition coil from the cylinder head.

  1. Install the spark plug onto the ignition coil.

  1. Attach the spark plug assembly to the cylinder head.

  1. Crank the engine for less than 2 seconds and check the spark.

    OK:
    Sparks jump across electrode gap.

  1. Install the ignition coil.

  1. Reconnect the injector connectors.



NG
Go to step 31
OK


9.CHECK CYLINDER COMPRESSION PRESSURE
  1. Measure the cylinder compression pressure of the misfiring cylinder .



NG
CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION
OK


10.CHECK HARNESS AND CONNECTOR (ECM - INJECTOR)
A106388E21
  1. Disconnect the injector connector (of the misfiring cylinder).

  1. Disconnect the D74 ECM connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Cylinder
    Tester Connection
    Switch Condition
    Specified Condition
    No. 1
    D11-1 - Body ground
    Ignition switch ON
    11 to 14 V
    No. 2
    D26-1 - Body ground
    Ignition switch ON
    11 to 14 V
    No. 3
    D13-1 - Body ground
    Ignition switch ON
    11 to 14 V
    No. 4
    D24-1 - Body ground
    Ignition switch ON
    11 to 14 V
    No. 5
    D15-1 - Body ground
    Ignition switch ON
    11 to 14 V
    No. 6
    D22-1 - Body ground
    Ignition switch ON
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Cylinder
    Tester Connection
    Condition
    Specified Condition
    No. 1
    D11-2 - Body ground
    Always
    10 kΩ or higher
    D11-2 - D74-86 (#10)
    Always
    Below 1 Ω
    No. 2
    D26-2 - Body ground
    Always
    10 kΩ or higher
    D26-2 - D74-109 (#20)
    Always
    Below 1 Ω
    No. 3
    D13-2 - Body ground
    Always
    10 kΩ or higher
    D13-2 - D74-85 (#30)
    Always
    Below 1 Ω
    No. 4
    D24-2 - Body ground
    Always
    10 kΩ or higher
    D24-2 - D74-108 (#40)
    Always
    Below 1 Ω
    No. 5
    D15-2 - Body ground
    Always
    10 kΩ or higher
    D15-2 - D74-84 (#50)
    Always
    Below 1 Ω
    No. 6
    D22-2 - Body ground
    Always
    10 kΩ or higher
    D22-2 - D74-107 (#60)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


11.INSPECT ECM TERMINAL OF MISFIRING CYLINDER (#10, #20, #30, #40, #50 AND /OR #60 VOLTAGE)
A136305E19
  1. Disconnect the D74 ECM connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D74-86 (#10) - D74-43 (E01)
    Ignition switch ON
    11 to 14 V
    D74-109 (#20) - D74-43 (E01)
    Ignition switch ON
    11 to 14 V
    D74-85 (#30) - D74-43 (E01)
    Ignition switch ON
    11 to 14 V
    D74-108 (#40) - D74-43 (E01)
    Ignition switch ON
    11 to 14 V
    D74-84 (#50) - D74-43 (E01)
    Ignition switch ON
    11 to 14 V
    D74-107 (#60) - D74-43 (E01)
    Ignition switch ON
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - ECM)
OK


12.CHECK FUEL INJECTOR OF MISFIRING CYLINDER
  1. Check the injector injection (whether fuel volume is high or low, and whether injection pattern is poor) (Click here).



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


13.CHECK VALVE CLEARANCE OF MISFIRING CYLINDER
  1. Check the valve clearance .



NG
ADJUST VALVE CLEARANCE (Click here)
OK


14.CHECK AIR INDUCTION SYSTEM
  1. Check the air induction system for vacuum leakage .

    OK:
    No leakage from air induction system.



NG
REPAIR OR REPLACE AIR INDUCTION SYSTEM
OK


15.CHECK VALVE TIMING


    G036290E11
  1. Remove the cylinder head cover .

  1. Turn the crankshaft pulley, and align its groove with the timing mark "0" of the timing chain cover.

  1. Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing cap as shown in the illustration.
    If not, turn the crankshaft 1 revolution (360°), then align the marks as above.

    OK:
    Timing marks on camshaft timing gears are aligned as shown in the illustration.

  1. Reinstall the cylinder head cover .



NG
ADJUST VALVE TIMING
OK


16.CHECK FUEL PRESSURE
  1. Check the fuel pressure (Click here).



NG
CHECK AND REPLACE FUEL PUMP, PRESSURE REGULATOR, FUEL PIPE LINE AND FILTER
OK


17.READ VALUE USING TECHSTREAM (COOLANT TEMP)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch ON and turn the Techstream ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.

  1. Read the Data List twice, when the engine is both cold and warmed up.

    Standard:
    With cold engine: Same as ambient air temperature.
    With warm engine: 80 to 100°C (176 to 212°F).



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


18.INSPECT MASS AIR FLOW METER
  1. Inspection mass air flow meter (Click here).



NG
REPLACE MASS AIR FLOW METER (Click here)
OK

REPLACE ECM (Click here)  

19.CHECK AIR INDUCTION SYSTEM
  1. Check the air induction system for vacuum leakage .

    OK:
    No leakage from air induction system.



NG
REPAIR OR REPLACE AIR INDUCTION SYSTEM
OK


20.CHECK VALVE TIMING


    G036290E11
  1. Remove the cylinder head cover .

  1. Turn the crankshaft pulley, and align its groove with the timing mark "0" of the timing chain cover.

  1. Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing cap as shown in the illustration.
    If not, turn the crankshaft 1 revolution (360°), then align the marks as above.

    OK:
    Timing marks on camshaft timing gears are aligned as shown in the illustration.

  1. Reinstall the cylinder head cover .



NG
ADJUST VALVE TIMING
OK


21.CHECK FUEL PRESSURE
  1. Check the fuel pressure (Click here).



NG
CHECK AND REPLACE FUEL PUMP, PRESSURE REGULATOR, FUEL PIPE LINE AND FILTER
OK


22.READ VALUE USING TECHSTREAM (COOLANT TEMP)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch ON and turn the Techstream ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.

  1. Read the Data List twice, when the engine is both cold and warmed up.

    Standard:
    With cold engine: Same as ambient air temperature.
    With warm engine: 80 to 100°C (176 to 212°F).



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


23.INSPECT MASS AIR FLOW METER
  1. Inspection mass air flow meter (Click here).



NG
REPLACE MASS AIR FLOW METER (Click here)
OK


24.CHECK SPARK PLUG
  1. Remove the ignition coil and the spark plug of the misfiring cylinder (Click here).

  1. Measure the spark plug electrode gap .



NG
REPLACE SPARK PLUG
OK


25.CHECK FOR SPARKS AND IGNITION
  1. Disconnect the injector connectors to prevent the engine from starting.

    CAUTION:
    Always disconnect all injector connectors.

    NOTICE:
    Do not crank the engine for more than 2 seconds.

  1. Remove the ignition coil from the cylinder head.

  1. Install the spark plug onto the ignition coil.

  1. Attach the spark plug assembly to the cylinder head.

  1. Crank the engine for less than 2 seconds and check the spark.

    OK:
    Sparks jump across electrode gap.

  1. Install the ignition coil.

  1. Reconnect the injector connectors.



NG
Go to step 31
OK


26.CHECK CYLINDER COMPRESSION PRESSURE
  1. Measure the cylinder compression pressure of the misfiring cylinder .



NG
CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION
OK


27.CHECK HARNESS AND CONNECTOR (ECM - INJECTOR)
A106388E21
  1. Disconnect the injector connector (of the misfiring cylinder).

  1. Disconnect the D74 ECM connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Cylinder
    Tester Connection
    Switch Condition
    Specified Condition
    No. 1
    D11-1 - Body ground
    Ignition switch ON
    11 to 14 V
    No. 2
    D26-1 - Body ground
    Ignition switch ON
    11 to 14 V
    No. 3
    D13-1 - Body ground
    Ignition switch ON
    11 to 14 V
    No. 4
    D24-1 - Body ground
    Ignition switch ON
    11 to 14 V
    No. 5
    D15-1 - Body ground
    Ignition switch ON
    11 to 14 V
    No. 6
    D22-1 - Body ground
    Ignition switch ON
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Cylinder
    Tester Connection
    Condition
    Specified Condition
    No. 1
    D11-2 - Body ground
    Always
    10 kΩ or higher
    D11-2 - D74-86 (#10)
    Always
    Below 1 Ω
    No. 2
    D26-2 - Body ground
    Always
    10 kΩ or higher
    D26-2 - D74-109 (#20)
    Always
    Below 1 Ω
    No. 3
    D13-2 - Body ground
    Always
    10 kΩ or higher
    D13-2 - D74-85 (#30)
    Always
    Below 1 Ω
    No. 4
    D24-2 - Body ground
    Always
    10 kΩ or higher
    D24-2 - D74-108 (#40)
    Always
    Below 1 Ω
    No. 5
    D15-2 - Body ground
    Always
    10 kΩ or higher
    D15-2 - D74-84 (#50)
    Always
    Below 1 Ω
    No. 6
    D22-2 - Body ground
    Always
    10 kΩ or higher
    D22-2 - D74-107 (#60)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


28.INSPECT ECM TERMINAL OF MISFIRING CYLINDER (#10, #20, #30, #40, #50 AND /OR #60 VOLTAGE)
A136305E19
  1. Disconnect the D74 ECM connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D74-86 (#10) - D74-43 (E01)
    Ignition switch ON
    11 to 14 V
    D74-109 (#20) - D74-43 (E01)
    Ignition switch ON
    11 to 14 V
    D74-85 (#30) - D74-43 (E01)
    Ignition switch ON
    11 to 14 V
    D74-108 (#40) - D74-43 (E01)
    Ignition switch ON
    11 to 14 V
    D74-84 (#50) - D74-43 (E01)
    Ignition switch ON
    11 to 14 V
    D74-107 (#60) - D74-43 (E01)
    Ignition switch ON
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - ECM)
OK


29.CHECK FUEL INJECTOR OF MISFIRING CYLINDER
  1. Check the injector injection (whether fuel volume is high or low, and whether injection pattern is poor) (Click here).



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


30.CHECK VALVE CLEARANCE OF MISFIRING CYLINDER
  1. Check the valve clearance .



NG
ADJUST VALVE CLEARANCE
OK

REPLACE ECM (Click here)  

31.CHANGE TO NORMAL SPARK PLUG AND CHECK SPARK OF MISFIRING CYLINDER
  1. Change the installed spark plug to a spark plug that functions normally.

  1. Perform a spark test.

    CAUTION:
    Always disconnect all injector connectors.

    NOTICE:
    Do not crank the engine for more than 2 seconds.

    1. Install the spark plug to the ignition coil and connect the ignition coil connector.

    2. Disconnect the injector connector.

    3. Ground the spark plug.

    4. Check if sparks occur while the engine is being cranked.

      OK:
      Sparks jump across electrode gap.



NG
Go to step 32
OK

REPLACE SPARK PLUG  

32.CHANGE TO NORMAL IGNITION COIL AND CHECK SPARK OF MISFIRING CYLINDER


NG
REPLACE ECM (Click here)
OK

REPLACE IGNITION COIL (Click here)