Home › Engine / Hybrid System › 3UR-FE ENGINE MECHANICAL › ENGINE UNIT
RM27M0U _51 Engine / Hybrid System _049106 3UR-FE ENGINE MECHANICAL _0234028 ENGINE UNIT A

3UR-FE ENGINE MECHANICAL  ENGINE UNIT  INSTALLATION  


PROCEDURE

Hide 82121 4.INSTALL ENGINE WIRE

A160651

a.

Connect the 3 clamps and 4 knock sensor connectors.


Hide 16206 8.INSTALL WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 83530 11.INSTALL OIL PRESSURE SENDER GAUGE ASSEMBLY

Hide 16603 12.INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY

Hide 16355 16.INSTALL FRONT WATER BY-PASS JOINT

Hide 16261G 17.INSTALL NO. 1 WATER BY-PASS HOSE

Hide 16206A 18.INSTALL NO. 2 WATER BY-PASS PIPE

Hide 23901 19.INSTALL FUEL TUBE SUB-ASSEMBLY

A256360

Hide 23902 20.INSTALL NO. 2 FUEL TUBE SUB-ASSEMBLY

a.
A256359

Install the No. 2 fuel tube with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 44763A 22.INSTALL NO. 1 TUBE

a.
A163943

Install the No. 1 tube with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 12262 23.CONNECT VENTILATION HOSE ASSEMBLY

Hide 23807 24.INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY RH

Hide 23808 25.INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY LH

Hide 12315 26.INSTALL NO. 1 ENGINE MOUNTING BRACKET LH

A160648

a.

Install the mounting bracket with the 4 bolts.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)


Hide 12311 27.INSTALL NO. 1 ENGINE MOUNTING BRACKET RH

A160649

a.

Install the mounting bracket with the 4 bolts.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)


Hide 12361 28.INSTALL FRONT ENGINE MOUNTING INSULATOR RH

a.
A163786

Install the mounting insulator with the nut.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)


Hide 11415A 29.INSTALL CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY

A076531E24
1.406,0.281 2.01,0.688 false 0.604,0.146 1.5,0.354 0.896,0.208 10 false Adhesive

a.

Apply adhesive to 2 or 3 threads of the drain cocks.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



b.
A380020E02
1.698,2.198 1.208,2.135 1.208,2.135 1.5,1.979 true 5,2.156 4.51,2.094 4.51,2.094 4.823,1.938 true 0.281,0.292 0.74,0.49 0.458,0.198 10 false LH: 0.958,1.396 1.417,1.594 0.458,0.198 10 false Front 3.729,0.292 4.188,0.49 0.458,0.198 10 false RH: 5.792,1.396 6.25,1.594 0.458,0.198 10 false Front 0.969,2.052 1.427,2.25 0.458,0.198 10 false 30° 4.281,2.031 4.74,2.229 0.458,0.198 10 false 30° 1.406,2.438 1.865,2.635 0.458,0.198 10 false 50° 4.813,2.438 5.271,2.635 0.458,0.198 10 false 50°

Install the water drain cocks.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


c.

Further tighten the drain cocks within 360° so that the drain cock pipes are within the range shown in the illustration.

NOTICE:
·

Do not rotate the drain cocks more than 1 revolution (360°) after tightening the drain cocks to the specified torque.

·

Do not loosen the drain cocks to adjust them. If an adjustment is necessary, remove the drain cocks and reinstall them.




d.

Install the water drain cock plugs to the water drain cocks.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 12362A 30.INSTALL FRONT ENGINE MOUNTING INSULATOR LH

a.
A163787

Install the mounting insulator with the nut.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)


Hide 23801P 31.INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY

A308965

a.

Install the No. 1 fuel pipe (see page Engine / Hybrid System>3UR-FE FUEL>FUEL SYSTEM>PRECAUTION).


Hide 32.INSTALL ENGINE WIRE

A259652E01
2.523,2.083 2.784,2.252 0.261,0.169 10 45° 2.867,2.406 3.123,2.569 0.256,0.164 10 45° 1.043,2.872 1.282,3.042 0.239,0.171 10 45° 0.404,2.891 0.649,3.064 0.245,0.173 10 45°

a.

Install the engine wire.


b.

Engine Rear Side:

i.

Install the 3 wires with the 3 bolts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


ii.

Connect the 5 clamps.


iii.

Connect the 3 connectors.



c.
A259650

Engine RH Side:

i.

Connect the 9 clamps.


ii.

Connect the oil pressure sender gauge connector.


iii.

Connect the throttle sensor connector.


iv.

Connect the fuel injector connector.


v.

Connect the 2 VVT sensor connectors.


vi.

Connect the 4 ignition coil connectors.


vii.

Connect the 2 camshaft timing control valve connectors.



d.
A259653

Engine LH Side:

i.

Connect the 8 clamps and install the engine wire with the bolt.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


ii.

Connect the fuel injector connector.


iii.

Connect the engine coolant temperature sensor connector.


iv.

Connect the purge VSV connector.


v.

Connect the vacuum switching valve connector (for ACIS).


vi.

Connect the camshaft position sensor connector.


vii.

Connect the 2 VVT sensor connectors.


viii.

Connect the 4 ignition coil connectors.


ix.

Connect the 2 camshaft timing control valve connector.