Home › Power Source / Network › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM
RM27M0U _57 Power Source / Network _049168 CAN COMMUNICATION _0234510 CAN COMMUNICATION SYSTEM J

CAN COMMUNICATION  CAN COMMUNICATION SYSTEM  Open in One Side of CAN Branch Line  


DESCRIPTION

If 2 or more ECUs and/or sensors do not appear on the Techstream "Bus Check" screen, one side of the CAN branch wire may be open (one side of the CANH [CAN branch wire]/CANL [CAN branch wire] of the ECU and/or sensor is open).

Symptom Trouble Area
2 or more ECUs and/or sensors do not appear on the Techstream "Bus Check" screen.
·

Center airbag sensor assembly

·

Main body ECU (driver side junction block assembly)

·

Steering angle sensor

·

Brake actuator assembly (skid control ECU)

·

Air conditioning amplifier assembly

·

4WD control ECU*1

·

Bus buffer ECU*2

·

Network gateway ECU*3

·

Radio and display receiver assembly*4

·

Navigation receiver assembly*5

·

Brake control with bracket relay*6



*1: for 4WD

*2: w/ Bus Buffer ECU

*3: w/ Blind Spot Monitor System

*4: w/ Audio and Visual System

*5: w/ Navigation System

*6: w/ Trailer Brake Control System


WIRING DIAGRAM

C308789E03
0.719,4.302 1.115,4.479 0.396,0.177 10 false CANH 0.74,4.854 1.125,5.031 0.385,0.177 10 false CANL 0.229,5.229 0.583,5.396 0.354,0.167 10 false J156 0.219,5.406 1.396,5.792 1.177,0.385 10 false Brake Control with Bracket Relay*1 2.969,4.229 3.073,4.365 0.104,0.135 10 false 7 2.896,4.75 3.052,4.927 0.156,0.177 10 false 18 2.958,6.115 3.063,6.271 0.104,0.156 10 false 1 2.896,6.615 3.052,6.792 0.156,0.177 10 false 12 1.229,4.74 1.417,4.896 0.188,0.156 10 false 10 1.24,4.219 1.385,4.375 0.146,0.156 10 false 4 6.01,4.354 6.438,4.531 0.427,0.177 10 false CANH 6.021,4.875 6.406,5.042 0.385,0.167 10 false CANL 5.719,5.177 5.917,5.333 0.198,0.156 10 false J6 5.698,5.354 7.083,5.552 1.385,0.198 10 false Steering Angle Sensor 3.854,4.219 3.948,4.406 0.094,0.188 10 false 6 3.854,4.74 4.021,4.917 0.167,0.177 10 false 17 5.813,4.75 5.896,4.927 0.083,0.177 10 false 9 5.74,4.281 5.917,4.448 0.177,0.167 10 false 10 6.01,6.219 6.427,6.385 0.417,0.167 10 false CANH 6.031,6.729 6.448,6.906 0.417,0.177 10 false CANL 5.51,7.042 5.833,7.198 0.323,0.156 10 false A17 5.5,7.198 7.083,7.51 1.583,0.313 10 false Brake Actuator Assembly (Skid Control ECU) 2.781,7.094 3.042,7.26 0.26,0.167 10 false J75 2.771,7.25 4.344,7.458 1.573,0.208 10 false No. 1 Junction Connector 3.854,6.115 3.958,6.271 0.104,0.156 10 false 8 3.854,6.635 4.042,6.792 0.188,0.156 10 false 19 5.74,6.656 5.917,6.813 0.177,0.156 10 false 13 5.74,6.115 5.917,6.281 0.177,0.167 10 false 12 6.021,2.448 6.417,2.604 0.396,0.156 10 false CANH 6.042,2.865 6.438,3.052 0.396,0.188 10 false CANL 5.906,3.354 6.188,3.521 0.281,0.167 10 false J46 5.906,3.531 7.021,3.948 1.115,0.417 10 false Center Airbag Sensor Assembly 3.854,2.344 3.948,2.51 0.094,0.167 10 false 3 3.854,2.854 4.021,3.031 0.167,0.177 10 false 14 5.75,2.875 5.927,3.052 0.177,0.177 10 false 22 5.729,2.344 5.896,2.51 0.167,0.167 10 false 13 6.042,0.458 6.458,0.635 0.417,0.177 10 false CANH 6.052,1.229 6.448,1.375 0.396,0.146 10 false CANL 5.875,1.49 6.135,1.646 0.26,0.156 10 false J28 5.865,1.656 7.052,2.031 1.188,0.375 10 false Combination Meter Assembly 3.844,0.49 3.948,0.646 0.104,0.156 10 false 4 3.854,0.99 4.031,1.167 0.177,0.177 10 false 15 5.74,1.01 5.917,1.167 0.177,0.156 10 false 40 5.74,0.479 5.917,0.625 0.177,0.146 10 false 39 0.74,2.458 1.156,2.615 0.417,0.156 10 false CANH 0.771,2.99 1.135,3.167 0.365,0.177 10 false CANL 0.229,3.354 0.427,3.521 0.198,0.167 10 false J2 0.198,3.542 1.99,3.958 1.792,0.417 10 false Main Body ECU (Driver Side Junction Block Assembly) 2.948,2.333 3.052,2.5 0.104,0.167 10 false 5 2.896,2.854 3.073,3.031 0.177,0.177 10 false 16 1.25,2.875 1.365,3.052 0.115,0.177 10 false 6 1.25,2.344 1.365,2.5 0.115,0.156 10 false 5 0.719,0.594 1.135,0.75 0.417,0.156 10 false CANH 0.75,1.115 1.146,1.281 0.396,0.167 10 false CANL 0.563,1.479 0.781,1.635 0.219,0.156 10 false J17 0.5,1.646 0.885,1.802 0.385,0.156 10 false DLC3 2.948,0.5 3.052,0.646 0.104,0.146 10 false 2 2.875,0.979 3.052,1.156 0.177,0.177 10 false 13 1.24,1 1.417,1.156 0.177,0.156 10 false 14 1.25,0.469 1.385,0.656 0.135,0.188 10 false 6 0.198,7.219 2.521,7.365 2.323,0.146 10 false *1: w/ Trailer Brake Control System

C288311E02
0.221,5.471 0.633,5.609 0.413,0.139 10 J135 0.221,5.625 1.522,6.039 1.302,0.415 10 Navigation Receiver Assembly*4 0.221,7.343 0.822,7.482 0.601,0.139 10 J123 0.221,7.498 2.135,7.912 1.914,0.415 10 Network Gateway ECU*6 2.981,6.376 3.081,6.515 0.100,0.139 10 6 2.907,6.896 3.080,7.035 0.173,0.139 10 17 0.718,4.586 1.131,4.725 0.413,0.139 10 CANH 0.718,5.106 1.131,5.245 0.413,0.139 10 CANL 1.257,5.026 1.431,5.164 0.173,0.139 10 10 1.257,4.506 1.431,4.644 0.173,0.139 10 9 0.741,6.457 1.131,6.595 0.390,0.139 10 CA1H 0.76,6.977 1.131,7.115 0.371,0.139 10 CA1L 1.257,6.896 1.431,7.035 0.173,0.139 10 15 1.257,6.376 1.431,6.515 0.173,0.139 10 16 6.058,4.586 6.471,4.725 0.413,0.139 10 CAN+ 6.058,5.106 6.471,5.245 0.413,0.139 10 CAN- 5.889,5.471 6.302,5.609 0.413,0.139 10 J59 5.889,5.625 7.024,6.039 1.135,0.415 10 Bus Buffer ECU*5 3.868,4.506 3.968,4.644 0.100,0.139 10 5 3.868,5.026 4.041,5.164 0.173,0.139 10 16 5.827,5.026 5.923,5.164 0.097,0.139 10 2 5.827,4.506 5.923,4.644 0.097,0.139 10 3 6.058,6.38 6.471,6.518 0.413,0.139 10 CANH 6.058,7.096 6.471,7.235 0.413,0.139 10 CANL 6.208,7.348 6.621,7.487 0.413,0.139 10 A24 6.208,7.502 6.636,7.686 0.428,0.183 10 ECM 2.78,7.348 3.193,7.487 0.413,0.139 10 J74 2.78,7.502 4.494,7.917 1.714,0.415 10 No. 2 Junction Connector 3.868,6.397 3.968,6.536 0.100,0.139 10 3 3.868,6.917 4.041,7.056 0.173,0.139 10 14 5.75,6.917 5.923,7.056 0.173,0.139 10 11 5.75,6.397 5.923,6.536 0.173,0.139 10 10 5.806,3.589 6.219,3.727 0.413,0.139 10 A25 5.806,3.743 7.108,4.157 1.302,0.415 10 4WD Control ECU*2 3.868,2.624 3.968,2.762 0.100,0.139 10 2 3.868,3.144 4.041,3.282 0.173,0.139 10 13 5.75,3.144 5.923,3.282 0.173,0.139 10 22 6.058,2.704 6.471,2.843 0.413,0.139 10 CANH 6.058,3.224 6.471,3.363 0.413,0.139 10 CANL 5.75,2.624 5.923,2.762 0.173,0.139 10 23 6.058,0.822 6.471,0.961 0.413,0.139 10 CANH 6.058,1.342 6.471,1.481 0.413,0.139 10 CANL 5.75,0.742 5.923,0.880 0.173,0.139 10 11 5.876,1.706 6.289,1.845 0.413,0.139 10 J19 5.876,1.861 7.081,2.275 1.205,0.415 10 Air Conditioning Amplifier Assembly 3.868,0.742 3.968,0.880 0.100,0.139 10 1 3.868,1.262 4.041,1.400 0.173,0.139 10 12 5.75,1.262 5.923,1.400 0.173,0.139 10 12 0.718,2.709 1.131,2.847 0.413,0.139 10 CANH 0.718,3.229 1.131,3.368 0.413,0.139 10 CANL 0.221,3.593 0.633,3.732 0.413,0.139 10 J139 0.221,3.747 2.015,4.162 1.795,0.415 10 Radio and Display Receiver Assembly*3 2.981,2.628 3.081,2.767 0.100,0.139 10 7 2.907,3.148 3.080,3.287 0.173,0.139 10 18 1.257,3.148 1.431,3.287 0.173,0.139 10 10 1.257,2.628 1.431,2.767 0.173,0.139 10 9 2.981,0.742 3.081,0.880 0.100,0.139 10 4 2.907,1.262 3.080,1.400 0.173,0.139 10 15 0.3,7.965 2.222,8.114 1.922,0.148 10 *2: for 4WD 0.3,8.259 2.854,8.408 2.554,0.148 10 *3: w/ Audio and Visual System 0.3,8.554 2.222,8.702 1.922,0.148 10 *4: w/ Navigation System 2.574,7.965 5.128,8.114 2.554,0.148 10 *5: w/ Bus Buffer ECU 2.574,8.259 5.128,8.408 2.554,0.148 10 *6: w/ Blind Spot Monitor System

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the Precaution in the SRS (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).



HINT:
·

Perform the following inspection for the ECUs (sensors) which are displayed on the Techstream. If a malfunction cannot be identified, perform the following inspections for the ECUs (sensors) connected to the CAN communication system.

·

Do not remove the combination meter assembly and ECM, as they are the end parts of the circuit. If removed, CAN communication will not be possible.

·

The open circuit confirmation of the combination meter assembly, ECM and CAN main wire is performed in the Check CAN Bus Line procedure of "How to Proceed with Troubleshooting". This inspection only has procedures for checking for an open circuit on one side of the CAN branch wire.



PROCEDURE

1.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (CENTER AIRBAG SENSOR ASSEMBLY)

b.

Select "Bus Check" on the Techstream (See page Power Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

Result
Result Proceed to
"Airbag" is not displayed on the Techstream A
Several ECUs and sensors in addition to "Airbag" are displayed on the Techstream B



A

2.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (CENTER AIRBAG SENSOR ASSEMBLY CAN BRANCH WIRE)

B

3.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (MAIN BODY ECU)
2.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (CENTER AIRBAG SENSOR ASSEMBLY CAN BRANCH WIRE)
a.
U152453E03
2,1 2.469,0.417 2.469,0.417 2.552,0.417 true 2.135,1.25 2.49,1.656 2.49,1.656 2.573,1.656 true 0.417,0.99 0.667,1.135 0.25,0.146 10 false J46 2.615,0.354 3.052,0.531 0.438,0.177 10 false CANH 0.094,0.073 0.302,0.25 0.208,0.177 10 false *a 2.635,1.583 3.042,1.76 0.406,0.177 10 false CANL

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J46-13 (CANH) - J46-22 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Center Airbag Sensor Assembly)

Result
Result Proceed to
OK (for Column Shift Type) A
OK (for Floor Shift Type) B
NG C



A

B

C

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CENTER AIRBAG SENSOR ASSEMBLY)

3.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (MAIN BODY ECU)
a.

Disconnect the J2 main body ECU (driver side junction block assembly) connector.


b.

Select "Bus Check" on the Techstream (See page Power Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

Result
Result Proceed to
"Main Body" is not displayed on the Techstream A
Several ECUs and sensors in addition to "Main Body" are displayed on the Techstream B



A

4.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (MAIN BODY ECU CAN BRANCH WIRE)

B

5.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (STEERING ANGLE SENSOR)
4.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (MAIN BODY ECU CAN BRANCH WIRE)
a.
U152508E01
1.53,1.359 1.871,1.926 1.871,1.926 2.01,1.926 false 1.414,1.359 1.073,1.926 1.073,1.926 0.935,1.926 false 2.057,1.853 2.478,1.989 0.422,0.137 10 CANL 0.385,1.853 0.807,1.989 0.422,0.137 10 CANH 0.7,1.161 0.876,1.298 0.176,0.137 10 J2 0.067,0.048 0.267,0.185 0.199,0.137 10 *a

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J2-5 (CANH) - J2-6 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Main Body ECU [Driver Side Junction Block Assembly])



OK

REPLACE MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (MAIN BODY ECU)

5.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (STEERING ANGLE SENSOR)
a.

Disconnect the J6 steering angle sensor connector.


b.

Select "Bus Check" on the Techstream (See page Power Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

Result
Result Proceed to
"Spiral cable (Steering Angle Sensor)" is not displayed on the Techstream A
Several ECUs and sensors in addition to "Spiral cable (Steering Angle Sensor)" are displayed on the Techstream B



A

6.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (STEERING ANGLE SENSOR CAN BRANCH WIRE)

B

7.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (SKID CONTROL ECU)
6.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (STEERING ANGLE SENSOR CAN BRANCH WIRE)
a.
U152505E01
1.172,1.309 0.944,1.537 0.944,1.537 0.834,1.537 false 1.008,1.802 1.068,1.802 1.068,1.802 1.307,1.309 false 0.338,1.451 0.759,1.594 0.421,0.143 10 CANH 1.688,0.335 1.855,0.478 0.167,0.143 10 J6 0.51,1.72 0.931,1.863 0.421,0.143 10 CANL 0.058,0.035 0.253,0.178 0.195,0.143 10 *a

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J6-10 (CANH) - J6-9 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Steering Angle Sensor)



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (STEERING ANGLE SENSOR)

7.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (SKID CONTROL ECU)
a.

Disconnect the A17 brake actuator assembly (skid control ECU) connector.


b.

Select "Bus Check" on the Techstream (See page Power Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

Result
Result Proceed to
"Skid Control (ABS/VSC/TRAC)" is not displayed on the Techstream A
Several ECUs and sensors in addition to ""Skid Control (ABS/VSC/TRAC)" are displayed on the Techstream B



A

8.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (SKID CONTROL ECU CAN BRANCH WIRE)

B

9.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (4WD CONTROL ECU)
8.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (SKID CONTROL ECU CAN BRANCH WIRE)
a.
U152527E01
1.246,1.152 1.073,0.726 1.073,0.726 0.961,0.726 false 1.342,1.161 1.093,1.858 1.093,1.858 0.961,1.858 false 0.08,0.054 0.252,0.214 0.172,0.159 10 *a 1.568,0.576 1.836,0.713 0.268,0.137 10 A17 0.432,1.788 0.865,1.925 0.433,0.137 10 CANH 0.478,0.648 0.874,0.785 0.395,0.137 10 CANL

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A17-12 (CANH) - A17-13 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])



OK

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (SKID CONTROL ECU)

9.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (4WD CONTROL ECU)
NOTICE:

For vehicles without a 4WD, go to "Check for Open in One Side CAN Branch Wire (Bus Buffer ECU)".


a.

Disconnect the A25 4WD control ECU connector.


b.

Select "Bus Check" on the Techstream (See page Power Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

Result
Result Proceed to
"Four Wheel Drive Control" is not displayed on the Techstream A
Several ECUs and sensors in addition to "Four Wheel Drive Control" are displayed on the Techstream B



A

10.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (4WD CONTROL ECU CAN BRANCH WIRE)

B

11.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (BUS BUFFER ECU)
10.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (4WD CONTROL ECU CAN BRANCH WIRE)
a.
U152605E01
0.121,0.065 0.356,0.342 0.235,0.276 10 *a 0.748,1.801 1.140,1.939 0.392,0.137 10 CANL 0.588,1.558 1.003,1.695 0.415,0.137 10 CANH 0.544,1.074 0.811,1.211 0.267,0.137 10 A25 1.452,1.383 1.25,1.632 1.25,1.632 1.095,1.632 false 1.224,1.877 1.39,1.877 1.39,1.877 1.526,1.383 false

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A25-23 (CANH) - A25-22 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to 4WD Control ECU)



OK

REPLACE 4WD CONTROL ECU

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (4WD CONTROL ECU)

11.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (BUS BUFFER ECU)
NOTICE:

For vehicles without a bus buffer ECU, go to "Check for Open in One Side CAN Branch Wire (Network Gateway ECU)".


a.

Disconnect the J59 bus buffer ECU connector.


b.

Select "Bus Check" on the Techstream (See page Power Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

Result
Result Proceed to
"Accessory Gateway" is not displayed on the Techstream A
Several ECUs and sensors in addition to "Accessory Gateway" are displayed on the Techstream B



A

12.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (BUS BUFFER ECU CAN BRANCH WIRE)

B

13.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (NETWORK GATEWAY ECU)
12.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (BUS BUFFER ECU CAN BRANCH WIRE)
a.
U152607E01
0.878,1.823 1.395,1.965 0.517,0.142 10 CAN- 2.375,1.823 2.892,1.965 0.517,0.142 10 CAN+ 0.119,0.092 0.636,0.234 0.517,0.142 10 *a 0.516,1.084 0.760,1.226 0.244,0.142 10 J59 1.996,1.424 2.15,1.901 2.15,1.901 2.326,1.901 false 1.696,1.424 1.543,1.901 1.543,1.901 1.366,1.901 false

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J59-3 (CAN+) - J59-2 (CAN-) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Bus Buffer ECU)



OK

REPLACE BUS BUFFER ECU

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (BUS BUFFER ECU)

13.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (NETWORK GATEWAY ECU)
NOTICE:

For vehicles without a blind spot monitor system, go to "Check for Open in One Side CAN Branch Wire (Brake Control with Bracket Relay)".


a.

Disconnect the J123 network gateway ECU connector.


b.

Select "Bus Check" on the Techstream (See page Power Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

Result
Result Proceed to
"CAN Gateway" is not displayed on the Techstream A
Several ECUs and sensors in addition to "CAN Gateway" are displayed on the Techstream B



A

14.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (NETWORK GATEWAY ECU CAN BRANCH WIRE)

B

15.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (BRAKE CONTROL WITH BRACKET RELAY)
14.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (NETWORK GATEWAY ECU CAN BRANCH WIRE)
a.
U152499E01
1.246,1.243 1.037,1.018 1.037,1.018 0.914,1.018 false 1.031,1.637 1.103,1.637 1.103,1.637 1.355,1.293 false 0.424,0.944 0.813,1.081 0.389,0.137 10 CA1H 0.582,1.551 0.970,1.688 0.389,0.137 10 CA1L 0.07,0.056 0.371,0.193 0.301,0.137 10 *a 2.747,1.159 3.068,1.296 0.321,0.137 10 J123

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J123-16 (CA1H) - J123-15 (CA1L) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Network Gateway ECU)



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (NETWORK GATEWAY ECU)

15.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (BRAKE CONTROL WITH BRACKET RELAY)
NOTICE:

For vehicles without a trailer brake control system, go to "Check for Open in One Side CAN Branch Wire (Air Conditioning Amplifier Assembly)".


a.

Disconnect the J156 brake control with bracket relay connector.


b.

Select "Bus Check" on the Techstream (See page Power Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

Result
Result Proceed to
"Trailer Brake Controller" is not displayed on the Techstream A
Several ECUs and sensors in addition to "Trailer Brake Controller" are displayed on the Techstream B



A

16.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (BRAKE CONTROL WITH BRACKET RELAY CAN BRANCH WIRE)

B

17.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY)
16.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (BRAKE CONTROL WITH BRACKET RELAY CAN BRANCH WIRE)
a.
U152659E01
1.526,0.315 1.856,0.456 0.330,0.141 10 J156 2.32,1.513 2.572,1.73 2.572,1.73 2.729,1.73 false 2.32,1.093 2.572,0.876 2.572,0.876 2.729,0.876 false 0.133,0.08 0.585,0.222 0.452,0.141 10 *a 2.756,0.799 3.180,0.940 0.424,0.141 10 CANH 2.756,1.646 3.156,1.787 0.400,0.141 10 CANL

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J156-4 (CANH) - J156-10 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Brake Control with Bracket Relay)



OK

REPLACE BRAKE CONTROL WITH BRACKET RELAY

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (BRAKE CONTROL WITH BRACKET RELAY)

17.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the J19 air conditioning amplifier assembly connector.


b.

Select "Bus Check" on the Techstream (See page Power Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

Result
Result Proceed to
"Air Conditioning Amplifier" is not displayed on the Techstream A
Several ECUs and sensors in addition to "Air Conditioning Amplifier" are displayed on the Techstream (w/ Audio and Visual System) B
Several ECUs and sensors in addition to "Air Conditioning Amplifier" are displayed on the Techstream (w/ Navigation System) C



A

18.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY CAN BRANCH WIRE)

B

19.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY CAN BRANCH WIRE)

C

20.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (NAVIGATION RECEIVER ASSEMBLY CAN BRANCH WIRE)
18.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY CAN BRANCH WIRE)
a.
U152458E03
1.771,1.344 2.229,1.875 2.229,1.875 2.323,1.875 true 1.688,1.365 1.24,1.896 1.24,1.896 1.146,1.896 true 0.365,1.302 0.615,1.448 0.25,0.146 10 false J19 0.74,1.844 1.125,1.99 0.385,0.146 10 false CANL 2.396,1.802 2.813,1.948 0.417,0.146 10 false CANH 0.052,0.042 0.333,0.188 0.281,0.146 10 false *a

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J19-11 (CANH) - J19-12 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly)



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY)

19.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY CAN BRANCH WIRE)
a.
U152464E01
1.536,0.415 1.860,0.555 0.324,0.140 10 J139 0.047,0.049 0.252,0.218 0.205,0.170 10 *a 2.039,1.299 2.26,1.774 2.26,1.774 2.366,1.774 false 1.908,1.299 1.687,1.774 1.687,1.774 1.581,1.774 false 1.079,1.699 1.490,1.837 0.411,0.139 10 CANH 2.398,1.699 2.809,1.837 0.411,0.139 10 CANL

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Disconnect the J139 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J139-9 (CANH) - J139-10 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)

Result
Result Proceed to
OK (for Column Shift Type) A
OK (for Floor Shift Type) B
NG C



A

B

C

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY)

20.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (NAVIGATION RECEIVER ASSEMBLY CAN BRANCH WIRE)
a.
U152463E01
0.047,0.049 0.252,0.218 0.205,0.170 10 *a 1.553,0.362 1.877,0.503 0.324,0.140 10 J135 2.039,1.299 2.26,1.774 2.26,1.774 2.366,1.774 false 1.908,1.299 1.687,1.774 1.687,1.774 1.581,1.774 false 1.079,1.699 1.490,1.837 0.411,0.139 10 CANH 2.398,1.699 2.809,1.837 0.411,0.139 10 CANL

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Disconnect the J135 navigation receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J135-9 (CANH) - J135-10 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Navigation Receiver Assembly)

Result
Result Proceed to
OK (for Column Shift Type) A
OK (for Floor Shift Type) B
NG C



A

B

C

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (NAVIGATION RECEIVER ASSEMBLY)