Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM3700E _51 Engine / Hybrid System _093506 HYBRID / BATTERY CONTROL _0441183 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P1C8349  High Voltage Power Resource Circuit Voltage Sensor after Boosting Malfunction  


DTC SUMMARY

MALFUNCTION DESCRIPTION


The hybrid vehicle control ECU monitors the high-voltage wiring between the HV battery and hybrid motor control inverter assembly and detects a power supply malfunction.

The cause of this malfunction may be one of the following:

Inverter voltage sensor (VH) internal circuit malfunction
·

Voltage sensor (VH) malfunction

·

Motor generator control ECU (MG ECU) malfunction

·

Communication (wire harness) malfunction


High voltage system malfunction
·

HV battery malfunction

·

No. 1 traction battery device box assembly malfunction

·

Hybrid motor control inverter assembly malfunction

·

Rear hybrid motor control inverter assembly (for AWD)

·

High-voltage wire harness malfunction

·

High-voltage connector or connection malfunction


Low-voltage circuit (12 V) malfunction
·

Hybrid vehicle control ECU malfunction

·

No. 1 traction battery device box assembly malfunction

·

Low voltage wire harness malfunction

·

Low voltage connector malfunction



INSPECTION DESCRIPTION


A476328E02
0.469,2.479 3.073,2.677 2.604,0.198 10 false Service Plug Grip 0.354,0.531 1.271,0.729 0.917,0.198 10 false *d, *e 2.573,0.521 2.885,0.719 0.313,0.198 10 false *b 0.74,0.302 2.271,0.5 1.531,0.198 10 false HV Battery 2.427,1.115 3.042,1.313 0.615,0.198 10 false SMRB 2.729,2.021 3.344,2.219 0.615,0.198 10 false SMRG 2.729,2.583 3.344,2.781 0.615,0.198 10 false SMRP 1.823,2.563 2.667,3.042 0.844,0.479 10 false System Main Resistor 3.833,0.781 4.146,0.979 0.313,0.198 10 false *c 4.635,2.021 5.667,2.448 1.031,0.427 10 false Boost Converter 5.917,2 6.417,2.385 0.5,0.385 10 false Inverter 1.167,3.438 3.979,3.635 2.813,0.198 10 false No. 1 Traction Battery Device Box Assembly 4.792,3.698 5.104,3.896 0.313,0.198 10 false *a 5.479,3.74 6.323,4.281 0.844,0.542 10 false System main relay signal 4.406,2.875 6.854,3.094 2.448,0.219 10 false Hybrid Motor Control Inverter Assembly 5.271,4.354 7.042,4.781 1.771,0.427 10 false Hybrid Vehicle Control ECU 1.115,4.729 4.021,4.927 2.906,0.198 10 false : High Voltage Line 1.115,5.063 3.865,5.26 2.75,0.198 10 false : Inspection Areas 0.104,0.073 0.885,0.323 0.781,0.25 12 false for 2WD:

A476329E04
0.125,0.073 1.354,0.271 1.229,0.198 12 false for AWD: 0.646,2.583 2.333,2.781 1.688,0.198 10 false Service Plug Grip 1.094,0.552 1.865,0.792 0.771,0.24 10 false HV Battery 2.781,1.313 3.198,1.479 0.417,0.167 10 false SMRB 3.083,2.188 3.5,2.354 0.417,0.167 10 false SMRG 3.094,2.823 3.51,2.99 0.417,0.167 10 false SMRP 2.198,2.792 3.104,3.177 0.906,0.385 10 false System Main Resistor 2.083,6.375 4.667,6.594 2.583,0.219 10 false Hybrid Motor Control Inverter Assembly 2.188,5.51 2.854,5.688 0.667,0.177 10 false Inverter 3.135,5.531 4.125,5.75 0.99,0.219 10 false Boost Converter 1.813,3.542 4.604,3.792 2.792,0.25 10 false No. 1 Traction Battery Device Box Assembly 0.281,4.531 1.771,5.01 1.49,0.479 10 false Hybrid Vehicle Control ECU 0.583,3.792 1.427,4.229 0.844,0.438 10 false System main relay signal 5.49,2.75 7.083,3.156 1.594,0.406 10 false Rear Hybrid Motor Control Inverter Assembly 6.354,2.188 7.021,2.365 0.667,0.177 10 false Inverter 5.396,4.021 5.615,4.229 0.219,0.208 10 false *c 0.729,3.146 0.948,3.354 0.219,0.208 10 false *a 4.188,0.938 4.406,1.146 0.219,0.208 10 false *c 2.917,0.75 3.135,0.958 0.219,0.208 10 false *b 0.552,0.771 1.031,0.979 0.479,0.208 10 false *d, *e 1.167,7.125 2.667,7.365 1.5,0.24 10 false : High Voltage Line 1.167,7.448 3.094,7.646 1.927,0.198 10 false : Inspection Areas

System Diagram Range Inspection Content Reason
*a Check connection condition and wire harness continuity between hybrid vehicle control ECU and No. 1 traction battery device box assembly In order to check whether connectors are connected properly and to check for an open circuit in the SMRP and SMRB primary lines
*b Check system main relay Check whether SMRB and SMRP stuck OFF
*c Check connection condition and high-voltage cable continuity between No. 1 traction battery device box assembly and hybrid motor control inverter assembly or rear hybrid motor control inverter assembly Check for open circuit and defective connection (arc marks) due to looseness
*d Check high-voltage cable and connection condition between HV battery and No. 1 traction battery device box assembly Check for open circuit and defective connection (arc marks) due to looseness
*e Check HV battery Check whether HV battery voltage has drastically dropped below normal range


DESCRIPTION

Refer to the description for DTC P0AE411.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AE411

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate DTC Output from Priority
P1C8349 High Voltage Power Resource Circuit Voltage Sensor after Boosting Malfunction Although an SMR on request was sent when the ignition switch is operated, the voltage did not increase after boosting.
High-voltage circuit malfunctions between the HV battery and hybrid motor control inverter assembly.
The EV electric battery fuse is blown, the service plug grip is removed, the system main resistor is blown, SMRP or SMRB remains open, or the high-voltage cable has an open circuit.
(1 trip detection logic)
·

No. 1 Traction Battery Device Box Assembly

·

HV floor under wire

·

Hybrid motor control inverter assembly

·

No. 1 HV supply stack sub-assembly

·

No. 2 HV supply stack sub-assembly

·

Hybrid battery terminal block

·

Electric vehicle battery plug assembly

·

Rear hybrid motor control inverter assembly*

·

HV battery pack wire*

·

Wire harness or connector


Does not come on Master Warning: Comes on Hybrid Control A

*: for AWD

Related Data List
DTC No. Data List
P1C8349
·

Hybrid/EV Battery Voltage

·

Hybrid/EV Battery Current

·

VL-Voltage before Boosting

·

VH-Voltage after Boosting



The following items can be helpful when performing repairs:

Data List
·

Ready Signal

·

Inter Lock Switch

·

SMRP Status

·

SMRB Status

·

SMRG Status


CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 2 minutes or more.

3.

Turn the ignition switch to ON (READY) and wait for 30 seconds or more.

4.

Turn the ignition switch off and wait for 2 minutes or more.

5.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

6.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

Refer to the wiring diagram for DTC P0AA649.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AA649

Refer to the wiring diagram for the HV Battery High-voltage Line Circuit.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>HV Battery High-voltage Line Circuit

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*

*: for AWD

-

Disconnecting the low voltage connector of the HV battery



·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.


·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.


·
A357589C58
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*.


*: for AWD



·
A358021C02
0.531,4.146 0.844,4.344 0.313,0.198 10 false *a 2.74,4.146 3.052,4.344 0.313,0.198 10 false *b
*a Dealer
*b Battery Collection Agent


When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.

·

Before returning the HV battery, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>RECOVERY INSPECTION

·

Before returning the HV supply stack sub-assembly, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>RECOVERY INSPECTION

·

Make a note of the output DTCs as some of them may be necessary for recovery inspection of the HV battery and HV supply stack sub-assemblies.


·
A358020

After removing the HV battery, keep it away from water. Exposure to water may cause the HV battery to produce heat, resulting in a fire.



NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL, MOTOR GENERATOR, HV BATTERY)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Powertrain > Motor Generator > Trouble Codes
50001 395
Powertrain > HV Battery > Trouble Codes
50001 398
Result:
Result Proceed to
P1C8349 and Microcomputer malfunction of Hybrid control system DTCs in the table below are output A
P1C8349 and Microcomputer malfunction of Motor generator control system DTCs in the table below are output B
P1C8349 and Microcomputer malfunction of Hybrid battery system DTCs in the table below are output C
P1C8349 and Power source circuit malfunction of Motor generator control system DTCs in the table below are output D
P1C8349 and Communication system malfunction of Hybrid control system DTCs in the table below are output E
P1C8349 and Sensor and actuator circuit malfunction of Hybrid control system DTCs in the table below are output F
P1C8349 and Sensor and actuator circuit malfunction of Hybrid battery system DTCs in the table below are output G
P1C8349 and System malfunction of Hybrid control system DTCs in the table below are output H
P1C8349 and System malfunction of Motor generator control system DTCs in the table below are output I
P1C8349 and DTCs other than the DTCs in the table below are output J
Only P1C8349 is output K


Malfunction Content System Relevant DTC
Microcomputer malfunction Hybrid control system P0A1B49 Drive Motor "A" Control Module Internal Electronic Failure
P060647 Hybrid/EV Powertrain Control Module Processor Watchdog / Safety MCU Failure
P060687 Hybrid/EV Powertrain Control Module Processor to Monitoring Processor Missing Message
P060A47 Hybrid/EV Powertrain Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060A87 Hybrid/EV Powertrain Control Module Processor from Monitoring Processor Missing Message
P1C9E9F Hybrid/EV System Reset Stuck Off
P060B49 Hybrid/EV Powertrain Control Module A/D Processing Internal Electronic Failure
Motor generator control system P0A1B1F Generator Control Module Circuit Intermittent
P0A1A47 Generator Control Module Watchdog / Safety MC Failure
P0A1A49 Generator Control Module Internal Electronic Failure
P1C2A1C Generator A/D Converter Circuit Circuit Voltage Out of Range
P1C2A49 Generator A/D Converter Circuit Internal Electronic Failure
P313383 Communication Error from Generator to Drive Motor "A" Value of Signal Protection Calculation Incorrect
P313386 Communication Error from Generator to Drive Motor "A" Signal Invalid
P313387 Communication Error from Generator to Drive Motor "A" Missing Message
Hybrid battery system P060B49 Hybrid/EV Battery Energy Control Module A/D Processing Internal Electronic Failure
P060687 Hybrid/EV Battery Energy Control Module Processor to Monitoring Processor Missing Message
P060A47 Hybrid/EV Battery Energy Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060A87 Hybrid/EV Battery Energy Control Module Processor from Monitoring Processor Missing Message
P0E2D00 Hybrid/EV Battery Energy Control Module Hybrid/EV Battery Monitor Performance
Power source circuit malfunction Motor generator control system P06D61C Generator Control Module Offset Power Circuit Voltage Out of Range
Communication system malfunction Hybrid control system P312387 Lost Communication with Drive Motor Control Module "A" from Hybrid/EV Control Module Missing Message
U011187 Lost Communication with Hybrid/EV Battery Energy Control Module "A" Missing Message
Sensor and actuator circuit malfunction Hybrid control system P0AD915 Hybrid/EV Battery Positive Contactor Circuit Short to Auxiliary Battery or Open
P0AD911 Hybrid/EV Battery Positive Contactor Circuit Short to Ground
P0AE415 Hybrid/EV Battery Precharge Contactor Circuit Short to Auxiliary Battery or Open
P0AE411 Hybrid/EV Battery Precharge Contactor Circuit Short to Ground
P0ADD15 Hybrid/EV Battery Negative Contactor Circuit Short to Auxiliary Battery or Open
P0ADD11 Hybrid/EV Battery Negative Contactor Circuit Short to Ground
P0B231C Hybrid/EV Battery "A" Voltage Sensor Voltage Out of Range
P0ABF00 Hybrid/EV Battery Current Sensor "A" Circuit Range/Performance
Hybrid battery system P0ABF11 Hybrid/EV Battery Current Sensor "A" Circuit Short to Ground
P0B0E11 Hybrid/EV Battery Current Sensor "B" Circuit Short to Ground
P0B0E15 Hybrid/EV Battery Current Sensor "B" Circuit Short to Auxiliary Battery or Open
P0ABF15 Hybrid/EV Battery Current Sensor "A" Circuit Short to Auxiliary Battery or Open
P301A1C Hybrid Battery Stack 1 Cell Voltage Detection Voltage Out of Range
P1A001C Hybrid Battery Stack 2 Cell Voltage Detection Voltage Out of Range
P1AFD1C Flying Capacitor/Internal Control Module Hybrid/EV Battery Monitor Voltage Out of Range
P0ABF28 Hybrid/EV Battery Current Sensor "A" Signal Bias Level Out of Range / Zero Adjustment Failure
P0ABF2A Hybrid/EV Battery Current Sensor "A" Signal Stuck In Range
P1CBB12 Hybrid/EV Battery Current Sensor Power Supply Circuit Short to Auxiliary Battery
P1CBB14 Hybrid/EV Battery Current Sensor Power Supply Circuit Short to Ground or Open
P0B1362 Hybrid/EV Battery Current Sensor "A"/"B" Signal Compare Failure
System malfunction Hybrid control system P0C7600 Hybrid/EV Battery System Discharge Time Too Long
P0D2D1C Drive Motor "A" Inverter Voltage Sensor Voltage Out of Range
P1C8149 High Voltage Power Resource Circuit Consumption Circuit Short
P1C8249 High Voltage Power Resource Circuit Over Loading
P0A1F94 Hybrid/EV Battery Energy Control Module Unexpected Operation
P300449 High Voltage Power Resource Circuit Short during Pre-Charge
Motor generator control system P0D2D16 Drive Motor "A" Inverter Voltage Sensor(VH) Circuit Voltage Below Threshold
P0D2D17 Drive Motor "A" Inverter Voltage Sensor(VH) Circuit Voltage Above Threshold
P1CB69E Drive Motor "A" Inverter Voltage Sensor(VH) Stuck On
P0CA300 DC/DC Converter Step Up Voltage Performance

HINT:
·

P1C8349 may be output as a result of the malfunction indicated by the DTCs above.

(a)

The chart above is listed in inspection order of priority.

(b)

Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)





Post-procedure1

a.

Turn the ignition switch off.



A

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

B

C

D

E

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

F

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

G

H

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

I

J

2.CHECK FREEZE FRAME DATA (HYBRID CONTROL)

K

2.CHECK FREEZE FRAME DATA (HYBRID CONTROL)
2.CHECK FREEZE FRAME DATA (HYBRID CONTROL)

Pre-procedure1

a.

None.


Procedure1

a.

Read the freeze frame data of DTC P1C8349.

Powertrain > Hybrid Control > DTC(P1C8349) > Freeze Frame Data
Tester Display
VL-Voltage before Boosting
VH-Voltage after Boosting
Hybrid/EV Battery Voltage
Hybrid/EV Battery Current
50040 397 150,151,227,228 P1C8349
Result:
Result Proceed to
All of the following conditions are met:
·

Difference between "Hybrid/EV Battery Voltage" and "VL-Voltage before Boosting" is 32 V or less.

·

Difference between "Hybrid/EV Battery Voltage" and "VH-Voltage after Boosting" is more than 33 V.

·

Difference between "VL-Voltage before Boosting" and "VH-Voltage after Boosting" is more than 56 V.


A
In addition to the above conditions, "Hybrid/EV Battery Current" is 3 A or more. B
Except above C



Post-procedure1

a.

Turn the ignition switch off.



A

REPLACE HYBRID MOTOR CONTROL INVERTER ASSEMBLY

B

C

3.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)
3.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

OK

4.CHECK CONNECTOR CONNECTION CONDITION (FLOOR WIRE CONNECTOR)

NG

CONNECT SECURELY

4.CHECK CONNECTOR CONNECTION CONDITION (FLOOR WIRE CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AA000

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

5.CHECK CONNECTOR CONNECTION CONDITION (NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY CONNECTOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK CONNECTOR CONNECTION CONDITION (NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY CONNECTOR)

OK

6.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY)

NG

CONNECT SECURELY

6.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY)

OK

7.CHECK VEHICLE CONDITION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK VEHICLE CONDITION
a.

Choose the model to be inspected.


Result:
Result Proceed to
for 2WD A
for AWD B



A

8.CHECK HARNESS AND CONNECTOR (NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY - BODY GROUND)

B

24.CHECK HARNESS AND CONNECTOR (NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY - BODY GROUND)
8.CHECK HARNESS AND CONNECTOR (NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY - BODY GROUND)

OK

9.INSPECT NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (SMRB)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (SMRB)

OK

10.INSPECT NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (SMRP)

NG

REPLACE NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY

10.INSPECT NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (SMRP)

OK

11.CHECK HYBRID MOTOR CONTROL INVERTER ASSEMBLY (HV FLOOR UNDER WIRE CONNECTION CONDITION)

NG

REPLACE NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY

11.CHECK HYBRID MOTOR CONTROL INVERTER ASSEMBLY (HV FLOOR UNDER WIRE CONNECTION CONDITION)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P300449

Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



A

12.CHECK NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (HV FLOOR UNDER WIRE CONNECTION CONDITION)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

12.CHECK NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (HV FLOOR UNDER WIRE CONNECTION CONDITION)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P300449

Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



A

13.CHECK FLOOR UNDER WIRE

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

13.CHECK FLOOR UNDER WIRE

OK

14.CHECK NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (HV BATTERY HIGH VOLTAGE CONNECTOR CONNECTION CONDITION)

NG

14.CHECK NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (HV BATTERY HIGH VOLTAGE CONNECTOR CONNECTION CONDITION)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P300449

Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



A

15.CHECK HYBRID BATTERY TERMINAL BLOCK (HV BATTERY HIGH VOLTAGE CONNECTOR CONNECTION CONDITION)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

15.CHECK HYBRID BATTERY TERMINAL BLOCK (HV BATTERY HIGH VOLTAGE CONNECTOR CONNECTION CONDITION)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P300449

Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



A

16.CHECK HV SUPPLY STACK SUB-ASSEMBLY (HV BATTERY HIGH VOLTAGE CONNECTOR CONNECTION CONDITION)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

16.CHECK HV SUPPLY STACK SUB-ASSEMBLY (HV BATTERY HIGH VOLTAGE CONNECTOR CONNECTION CONDITION)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P300449

Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



A

17.CHECK ELECTRIC VEHICLE BATTERY PLUG ASSEMBLY

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

17.CHECK ELECTRIC VEHICLE BATTERY PLUG ASSEMBLY

OK

18.CHECK HYBRID BATTERY TERMINAL BLOCK

NG

REPLACE ELECTRIC VEHICLE BATTERY PLUG ASSEMBLY

18.CHECK HYBRID BATTERY TERMINAL BLOCK

OK

19.CHECK NO. 2 HV SUPPLY STACK SUB-ASSEMBLY

NG

REPLACE HYBRID BATTERY TERMINAL BLOCK

19.CHECK NO. 2 HV SUPPLY STACK SUB-ASSEMBLY

OK

20.CHECK NO. 1 HV SUPPLY STACK SUB-ASSEMBLY

NG

REPLACE NO. 2 HV SUPPLY STACK SUB-ASSEMBLY

20.CHECK NO. 1 HV SUPPLY STACK SUB-ASSEMBLY

OK

21.CHECK FOR INTERMITTENT PROBLEMS

NG

REPLACE NO. 1 HV SUPPLY STACK SUB-ASSEMBLY

21.CHECK FOR INTERMITTENT PROBLEMS

NEXT

22.CLEAR DTC
22.CLEAR DTC

NEXT

23.CHECK DTC OUTPUT (HYBRID CONTROL)
23.CHECK DTC OUTPUT (HYBRID CONTROL)

Pre-procedure1

a.

None.


Procedure1

a.

Check if DTCs are output (including pending DTCs).

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
DTCs are not output A
P300449 is output B
P1C8349 is output C
None of the above conditions are met D


HINT:

Because P300449 uses 2-trip detection logic, the DTC detection conditions need to be met 2 times.



Post-procedure1

a.

Turn the ignition switch off.



A

REPLACE HYBRID MOTOR CONTROL INVERTER ASSEMBLY

B

C

REPLACE HYBRID MOTOR CONTROL INVERTER ASSEMBLY

D

24.CHECK HARNESS AND CONNECTOR (NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY - BODY GROUND)

OK

25.INSPECT NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (SMRB)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

25.INSPECT NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (SMRB)

OK

26.INSPECT NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (SMRP)

NG

REPLACE NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY

26.INSPECT NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (SMRP)

OK

27.CHECK HYBRID MOTOR CONTROL INVERTER ASSEMBLY (HV FLOOR UNDER WIRE CONNECTION CONDITION)

NG

REPLACE NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY

27.CHECK HYBRID MOTOR CONTROL INVERTER ASSEMBLY (HV FLOOR UNDER WIRE CONNECTION CONDITION)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P300449

Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



A

28.CHECK REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY (HV FLOOR UNDER WIRE)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

28.CHECK REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY (HV FLOOR UNDER WIRE)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P300449

Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



A

29.CHECK REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY (HV BATTERY PACK WIRE)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

29.CHECK REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY (HV BATTERY PACK WIRE)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P300449

Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



A

30.CHECK NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (HV BATTERY PACK WIRE)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

30.CHECK NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (HV BATTERY PACK WIRE)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P300449

Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



A

31.CHECK FLOOR UNDER WIRE

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

31.CHECK FLOOR UNDER WIRE

OK

14.CHECK NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (HV BATTERY HIGH VOLTAGE CONNECTOR CONNECTION CONDITION)

NG

32.CHECK FLOOR UNDER WIRE
32.CHECK FLOOR UNDER WIRE

OK

33.CHECK HV BATTERY PACK WIRE

NG

33.CHECK HV BATTERY PACK WIRE

OK

REPLACE REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY

NG