MALFUNCTION DESCRIPTION
This DTC indicates that the rear motor torque execution value does not correspond to the torque command value sent from the hybrid vehicle control ECU to the rear motor. The cause of this malfunction may be one of the following:
| Area | Main Malfunction Description |
|---|---|
| Inside of rear hybrid motor control inverter assembly | Rear hybrid motor control inverter assembly internal circuit malfunction |
| Rear traction motor assembly | ·
Motor (MGR) internal malfunction (entry of foreign matter, etc.) ·
Open or short circuit in the motor coils |
| Motor cable (for MGR) | ·
Open circuit or poor insulation on motor cable (for MGR) ·
Defective motor cable (for MGR) connection |
| Rear Inverter low-voltage circuit | The connectors are not connected properly |
| Hybrid vehicle control ECU | Hybrid vehicle control ECU internal circuit malfunction |
A DTC is stored when the actual rear motor torque deviates from the rear motor torque requested by the hybrid vehicle control ECU.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate | DTC Output from | Priority |
|---|---|---|---|---|---|---|---|
| P0C1A00 | Drive Motor "B" Execution Torque Performance | Rear motor torque execution monitoring malfunction:
The difference between the rear motor torque requested by the hybrid vehicle control ECU and actual rear motor torque is large. (1 trip detection logic) |
·
Wire harness or connector ·
Hybrid motor control inverter assembly ·
Rear hybrid motor control inverter assembly ·
Rear traction motor cable ·
Rear traction motor assembly ·
Hybrid vehicle control ECU |
Does not come on | Master Warning:
Comes on |
Rear Motor Generator | A |
| DTC No. | Data List |
|---|---|
| P0C1A00 | ·
Rear Motor Torque ·
Target Rear Motor Torque (Hybrid control system) ·
Vehicle Speed |
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>REAR MOTOR GENERATOR CONTROL SYSTEM>UTILITY
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for 2 minutes or more.
Turn the ignition switch to ON and wait for 5 seconds or more.
Turn the ignition switch to ON (READY) and wait for 5 seconds or more.
With the vehicle stopped, begin moving with the accelerator opening angle between 20% to 50% and a speed of approximately 10 km/h (6 mph), then stop the vehicle and repeat the same procedure several times, and check that the difference between "Rear motor torque" and "Target rear motor torque" is less than 18 N*m.
While doing this, check that the "Rear motor torque" value does not remain at 0 N*m continuously, but rather changes to indicate that the rear motor is operating.
Unless rear motor torque is restricted due to DTC output, the rear motor torque will not remain at 0 N*m continuously.
Enter the following menus: Powertrain / Rear Motor Generator / Utility / All Readiness.
Check the DTC judgment result.
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform the normal judgment procedure again.
Refer to the wiring diagram for the Rear Motor High-voltage Circuit.
Refer to the wiring diagram for the Shut Down Signal Circuit.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>Shut Down Signal Circuit
Refer to the wiring diagram for the Rear Shut Down Signal Circuit.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>Rear Shut Down Signal Circuit
Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.
Inspecting the high-voltage system
Disconnecting the low voltage connector of the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly
Disconnecting the low voltage connector of the HV battery
To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.
After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
| *a | Without waiting for 10 minutes |
After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly. The voltage should be 0 V before beginning work.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>REAR MOTOR GENERATOR CONTROL SYSTEM>PRECAUTION
Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly.
After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
When disconnecting and reconnecting the auxiliary battery
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
Pre-procedure1
None.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| Only P0C1A00 for Rear motor generator control system is output | A |
| P0C1A00 and DTCs other than the DTCs in the table below are output | B |
| P0C1A00 and Insulation malfunction of Hybrid control system DTCs in the table below are output | C |
| P0C1A00 and System main relay or high voltage circuit malfunction of Hybrid control system DTCs in the table below are output | D |
| P0C1A00 and Microcomputer malfunction of Motor generator control system DTCs in the table below are output | E |
| P0C1A00 and Microcomputer malfunction of Rear motor generator control system DTCs in the table below are output | F |
| P0C1A00 and Power source circuit malfunction of Rear motor generator control system DTCs in the table below are output | G |
| P0C1A00 and Sensor and actuator circuit malfunction of Rear motor generator control system DTCs in the table below are output | H |
| P0C1A00 and Sensor and actuator circuit malfunction of Hybrid control system DTCs in the table below are output | I |
| P0C1A00 and System malfunction of Motor generator control system DTCs in the table below are output | J |
| Malfunction Content | System | Relevant DTC | |
|---|---|---|---|
| Insulation malfunction | Hybrid control system | P1C7C49 | Hybrid/EV Battery Voltage System Isolation (A/C Area) Internal Electronic Failure |
| P1C7D49 | Hybrid/EV Battery Voltage System Isolation (Hybrid/EV Battery Area) Internal Electronic Failure | ||
| P1C7E49 | Hybrid/EV Battery Voltage System Isolation (Transaxle Area) Internal Electronic Failure | ||
| P1C7F49 | Hybrid/EV Battery Voltage System Isolation (Direct Current Area) Internal Electronic Failure | ||
| P1C8049 | Hybrid/EV Battery Voltage System Isolation (Rear Motor Area) Internal Electronic Failure | ||
| System main relay or high voltage circuit malfunction | Hybrid control system | P0AD911 | Hybrid/EV Battery Positive Contactor Circuit Short to Ground |
| P0AD915 | Hybrid/EV Battery Positive Contactor Circuit Short to Battery or Open | ||
| P0ADD11 | Hybrid/EV Battery Negative Contactor Circuit Short to Ground | ||
| P0ADD15 | Hybrid/EV Battery Negative Contactor Circuit Short to Battery or Open | ||
| P1C8449 | High Voltage Power Resource Circuit Short during Ready ON | ||
| Malfunction Content | System | Relevant DTC | |
|---|---|---|---|
| Microcomputer malfunction | Motor generator control system | P0A1C49 | Drive Motor B" Control Module Internal Electronic Failure" |
| Rear motor generator control system | P0A1C1F | Drive Motor B" Control Module Circuit Intermittent | |
| P1C2C1C | Drive Motor B" Control Module AD Converter Circuit Voltage Out of Range | ||
| P1C2C49 | Drive Motor B" Control Module AD Converter Circuit Internal Electronic Failure | ||
| Power source circuit malfunction | Rear motor generator control system | P06B31C | Drive Motor B" Control Module Position Sensor REF Power Source Circuit Voltage Out of Range |
| P262C1C | Drive Motor B" Control Module Offset Power Circuit Voltage Out of Range | ||
| Sensor and actuator circuit malfunction | Rear motor generator control system | P0A4516 | Drive Motor B" Position Sensor Circuit Voltage Below Threshold |
| P0A4521 | Drive Motor B" Position Sensor Signal Amplitude < Minimum | ||
| P0A4522 | Drive Motor B" Position Sensor Signal Amplitude > Maximum | ||
| P0A6912 | Drive Motor B" Phase V Current(High Resolution) Circuit Short to Battery | ||
| P0A6914 | Drive Motor B" Phase V Current(High Resolution) Circuit Short to Ground or Open | ||
| P0A691C | Drive Motor B" Phase V Current(High Resolution) Circuit Voltage Out of Range | ||
| P0A6C12 | Drive Motor B" Phase W Current(High Resolution) Circuit Short to Battery | ||
| P0A6C14 | Drive Motor B" Phase W Current(High Resolution) Circuit Short to Ground or Open | ||
| P0A6C1C | Drive Motor B" Phase W Current(High Resolution) Circuit Voltage Out of Range | ||
| P0BF512 | Drive Motor B" Phase V Current Sensor Circuit Short to Battery | ||
| P0BF514 | Drive Motor B" Phase V Current Sensor Circuit Short to Ground or Open | ||
| P0BF528 | Drive Motor B" Phase V Current Sensor Signal Bias Level Out of Range / Zero Adjustment Failure | ||
| P0BF912 | Drive Motor B" Phase W Current Sensor Circuit Short to Battery | ||
| P0BF914 | Drive Motor B" Phase W Current Sensor Circuit Short to Ground or Open | ||
| P0BF928 | Drive Motor B" Phase W Current Sensor Signal Bias Level Out of Range / Zero Adjustment Failure | ||
| P0C5513 | Drive Motor B" Position Sensor Circuit "A" Circuit Open | ||
| P0C5516 | Drive Motor B" Position Sensor Circuit "A" Circuit Voltage Below Threshold | ||
| P0C5517 | Drive Motor B" Position Sensor Circuit "A" Circuit Voltage Above Threshold | ||
| P0C5F13 | Drive Motor B" Position Sensor Circuit "B" Circuit Open | ||
| P0C5F16 | Drive Motor B" Position Sensor Circuit "B" Circuit Voltage Below Threshold | ||
| P0C5F17 | Drive Motor B" Position Sensor Circuit "B" Circuit Voltage Above Threshold | ||
| P0DA316 | Drive Motor B" Inverter Voltage Sensor "A" Circuit Voltage Below Threshold | ||
| P0DA317 | Drive Motor B" Inverter Voltage Sensor "A" Circuit Voltage Above Threshold | ||
| P1CAE49 | Drive Motor B" Position Sensor Internal Electronic Failure | ||
| P1CB138 | Drive Motor B" Position Sensor REF Signal Frequency Incorrect | ||
| P33C012 | Drive Motor B" Phase V Current Sensor Sub Circuit Short to Battery | ||
| P33C014 | Drive Motor B" Phase V Current Sensor Sub Circuit Short to Ground or Open | ||
| P33C028 | Drive Motor B" Phase V Current Sensor Sub Signal Bias Level Out of Range / Zero Adjustment Failure | ||
| P33C512 | Drive Motor B" Phase W Current Sensor Sub Circuit Short to Battery | ||
| P33C514 | Drive Motor B" Phase W Current Sensor Sub Circuit Short to Ground or Open | ||
| P33C528 | Drive Motor B" Phase W Current Sensor Sub Signal Bias Level Out of Range / Zero Adjustment Failure | ||
| P33D862 | Drive Motor B" Phase V Current Sensor Signal Compare Failure | ||
| P33D962 | Drive Motor B" Phase W Current Sensor Signal Compare Failure | ||
| Hybrid control system | P0DA31C | Drive Motor B" Inverter Voltage Sensor "A" Voltage Out of Range" | |
| System malfunction | Motor generator control system | P0A9000 | Drive Motor A" Performance" |
| P0A9200 | Hybrid Generator Performance | ||
| P0BFF1D | Drive Motor A" Circuit Current Out of Range" | ||
| P0C1900 | Drive Motor A" Execution Torque Performance" | ||
| P0E7100 | Generator Execution Torque Performance | ||
| P1CA51D | Hybrid Generator Circuit Current Out of Range | ||
P0C1A00 may be output as a result of the malfunction indicated by the DTCs above.
The chart above is listed in inspection order of priority.
Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)
Post-procedure1
Turn the ignition switch off.
A
B
C
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
D
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
E
F
G
H
I
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
J
Pre-procedure1
None.
Procedure1
Read the diagnosis related information for Motor Generator.
| Tester Display |
|---|
| Diagnosis Related Information |
| Result | Proceed to |
|---|---|
| Diagnosis Related Information P312487 is output | A |
| Diagnosis Related Information P312487 is not output | B |
Post-procedure1
Turn the ignition switch off.
A
B
Pre-procedure1
None.
Procedure1
Read the freeze frame data of DTC P0C1A00.
| Tester Display |
|---|
| Rear Inverter Shut Down Status |
| Result | Proceed to |
|---|---|
| The value of Rear Inverter Shut Down Status is ON | A |
| The value of Rear Inverter Shut Down Status is OFF | B |
Post-procedure1
Turn the ignition switch off.
A
B
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>REAR MOTOR GENERATOR CONTROL SYSTEM>P0A4516
| Result | Proceed to |
|---|---|
| OK | A |
| NG (The connector is not connected securely.) | B |
| NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) | C |
A
B
C
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>Shut Down Signal Circuit
| Proceed to |
|---|
| NEXT |
NEXT
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>Rear Shut Down Signal Circuit
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT