Home › Engine / Hybrid System › M15A-FKS (ENGINE CONTROL) › SFI SYSTEM
RM3700E _51 Engine / Hybrid System _093766 M15A-FKS ENGINE CONTROL _0442966 SFI SYSTEM C

M15A-FKS ENGINE CONTROL  SFI SYSTEM  P013616  A/F (O2) Sensor Circuit Bank 1 Sensor 2 Circuit Current (Voltage) Below Threshold  


DESCRIPTION

Refer to DTC P003612.

Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>P003612

HINT:

Although the DTC title say O2 sensor, this DTC relate to the air fuel ratio sensor (sensor 2).


DTC No. Detection Item DTC Detection Condition Trouble Area MIL DTC Output from Priority Note
P013616 A/F (O2) Sensor Circuit Bank 1 Sensor 2 Circuit Current (Voltage) Below Threshold Either of the following conditions is met (2 trip detection logic).
·

During active rich air-fuel ratio control, the air fuel ratio sensor (sensor 2) current is 6 mA or higher

·

During active rich air-fuel ratio control, the oxygen storage capacity of the catalyst is more than 2.0 g when the air fuel ratio sensor (sensor 2) current is -0.25757 mA or higher


·

Air fuel ratio sensor (sensor 2)

·

Air fuel ratio sensor (sensor 1)

·

Gas leak from exhaust system

·

EGR valve assembly

·

Fuel system

·

Intake system


Comes on Engine B SAE: P0136

MONITOR DESCRIPTION

Active Air fuel Ratio Control


The ECM usually performs air fuel ratio feedback control so that the air fuel ratio sensors output indicates a near stoichiometric air fuel ratio. This vehicle includes active air fuel ratio control in addition to regular air fuel ratio control. The ECM performs active air fuel ratio control to detect any deterioration in the Three-Way Catalytic Converter (TWC) and any malfunctions of the air fuel ratio sensor (sensor 2) (refer to the diagram below).

Active air fuel ratio control is performed for approximately 30 seconds while driving with a warm engine. During active air fuel ratio control, the air fuel ratio is forcibly regulated to become lean or rich by the ECM. If the ECM detects a malfunction, a DTC is stored.


Abnormal Air Fuel Ratio Sensor (Sensor 2) Output Current (DTC P013616)


Case 1: The ECM illuminates the MIL and stores a DTC when active rich air-fuel ratio control is being performed and the air fuel ratio sensor (sensor 2) current is 6 mA or higher.

Case 2: The ECM illuminates the MIL and stores a DTC when active rich air-fuel ratio control is being performed, the oxygen storage capacity of the catalyst is higher than 2.0 g and the air fuel ratio sensor (sensor 2) current is -0.25757 mA or higher.

A392731E02
4.302,4.01 4.948,3.656 true 4.229,2.385 5.021,2.594 true 6.042,3.792 6.583,4.344 true 6.042,3.792 6.677,3.083 true 0.146,0.177 5.781,0.51 5.635,0.333 10 false Air Fuel Ratio Sensor (Sensor 2) Output Current Malfunction (P013616) 0.073,1.063 1.375,1.479 1.302,0.417 10 false Active Air Fuel Ratio Control 4.573,0.844 5.208,1.052 0.635,0.208 10 false Operation 0.031,2.927 1.365,3.5 1.333,0.573 10 false Air Fuel Ratio Sensor (Sensor 2) Output Current 0.063,4.448 1.115,4.958 1.052,0.51 10 false Oxygen Storage Capacity 3.813,3.927 4.354,4.198 0.542,0.271 10 false Normal 3.052,2.292 4.333,2.625 1.281,0.333 10 false Abnormal (Case 1) 0.063,1.917 1.5,2.167 1.438,0.25 10 false Fuel Injection Volume 1.74,1.677 2.427,1.969 0.688,0.292 10 false Increase 1.688,2.156 2.552,2.406 0.865,0.25 10 false Decrease 1.552,2.594 2.292,3.042 0.74,0.448 10 false Malfunction Threshold 1.594,3.479 2.229,3.969 0.635,0.49 10 false Normal Threshold 5.385,3.708 6.01,4.094 0.625,0.385 10 false Abnormal (Case 2) 1.583,4.323 2.302,4.729 0.719,0.406 10 false Malfunction Threshold


MONITOR STRATEGY

Required Sensors/Components (Main) Air fuel ratio sensor (sensor 2)
Required Sensors/Components (Related) Crankshaft position sensor
Engine coolant temperature sensor
Mass air flow meter sub-assembly
Throttle position sensor
Air fuel ratio sensor (sensor 1)

TYPICAL ENABLING CONDITIONS

Battery voltage 11 V or higher
Intake air temperature -10°C (14°F) or higher
Engine coolant temperature 75°C (167°F) or higher
Atmospheric pressure 76 kPa(abs) [11.02 psi(abs)] or higher
Idling Off
Engine speed Less than 3200 rpm
Air fuel ratio sensor (sensor 1) status Activated
Fuel system status Closed loop
Engine load 10% or higher, and less than 100%

TYPICAL MALFUNCTION THRESHOLDS

Both of the following conditions are met A and B
A. Continuous time of active rich air fuel ratio control*1 0.5 seconds or more
*1: Target air fuel ratio 14.3 or less
B. Either of the following conditions is met (a) or (b)
(a) Air fuel ratio sensor (sensor 2) current 6 mA or higher
(b) OSC (Oxygen Storage Capacity) of catalyst More than 2.0 g

CONFIRMATION DRIVING PATTERN

HINT:
·

This confirmation driving pattern is used for the "Perform Confirmation Driving Pattern" procedure of the following diagnostic troubleshooting procedure.

·

Performing this confirmation driving pattern will activate the air fuel ratio sensor (sensor 2) monitor (the catalyst monitor is performed simultaneously). This is very useful for verifying the completion of a repair.



A264212E78
1.74,2.427 1.563,2.802 1.563,2.802 1.417,2.802 false 4.021,0.719 4.25,0.958 0.229,0.24 10 false [C] 3.49,2.906 4.792,3.083 1.302,0.177 10 false 10 minutes or more 1.094,1.354 1.698,1.51 0.604,0.156 10 false 75 km/h 2.021,2.427 2.25,2.625 0.229,0.198 10 false [A] 1.021,0.479 1.677,0.688 0.656,0.208 10 false 120 km/h 1.25,2.229 1.635,2.448 0.385,0.219 10 false Idling 0.229,2.719 1.615,2.958 1.385,0.24 10 false Ignition Switch ON 2.677,2.135 2.906,2.344 0.229,0.208 10 false [B] 2.333,2.917 3.156,3.115 0.823,0.198 10 false Warming up 5.01,3.313 5.271,3.573 0.26,0.26 10 false [D]

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON [A].

7.

Turn the GTS on.

8.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher with the shift lever in P or neutral [B].

9.

Drive the vehicle at 75 to 120 km/h (46 to 75 mph) for 10 minutes or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


10.

Enter the following menus: Powertrain / Engine / Trouble Codes [D].

11.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

13.

Input the DTC: P013616.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.

·

If the judgment result is INCOMPLETE, perform steps [C] through [D] again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:

Malfunctioning areas can be identified by performing the Active Test "Control the Injection Volume for A/F Sensor". This Active Test can help to determine whether the air fuel ratio sensors (sensor 1 and sensor 2) and other potential trouble areas are malfunctioning.

The following procedure describes how to perform the Active Test "Control the Injection Volume for A/F Sensor" using the GTS.


1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher.

5.

Warm up the air fuel ratio sensors at an engine speed of 2500 rpm for 90 seconds.

6.

Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / Data List / A/F (O2) Sensor Current B1S1 and A/F (O2) Sensor Current B1S2.

7.

Perform the Active Test with the engine idling (change the fuel injection volume).

8.

Monitor the output current of the air fuel ratio sensor (sensor 1) (A/F (O2) Sensor Current B1S1) and air fuel ratio sensor (sensor 2) (A/F (O2) Sensor Current B1S2) displayed on the GTS.


HINT:
·

The Active Test "Control the Injection Volume for A/F Sensor" can be used to lower the fuel injection volume by 12.5% or increase the injection volume by 12.5%.

·

Each sensor reacts in accordance with the increase and decrease in the fuel injection volume.



Standard
GTS Display (Sensor) Injection Volume Status Current
A/F (O2) Sensor Current B1S1
(Air fuel ratio sensor (sensor 1))
12.5% Rich Below -0.075 mA
-12.5% Lean Higher than 0.037 mA
A/F (O2) Sensor Current B1S2
(Air fuel ratio sensor (sensor 2))
12.5% Rich Below -0.86 mA
-12.5% Lean Higher than 0.33 mA

NOTICE:

The air fuel ratio sensor (sensor 1) has an output delay of a few seconds and the air fuel ratio sensor (sensor 2) has a maximum output delay of approximately 20 seconds.


A392732E02
0.135,0.802 0.531,1.01 0.396,0.208 10 false Case 0.906,0.688 2.958,1.115 2.052,0.427 10 false Air Fuel Ratio Sensor (Sensor 1) Output Current 3.542,0.708 5.594,1.115 2.052,0.406 10 false Air Fuel Ratio Sensor (Sensor 2) Output Current 5.99,0.729 6.99,1.104 1,0.375 10 false Main Suspected Trouble Area 0.24,2.24 0.563,2.448 0.323,0.208 10 false 1 0.667,1.385 1.896,1.583 1.229,0.198 10 false Injection Volume 1.417,1.729 1.969,1.948 0.552,0.219 10 false 12.5% 1.365,1.938 2.021,2.156 0.656,0.219 10 false -12.5% 0.688,2.354 1.823,2.594 1.135,0.24 10 false Output Current 0.635,2.729 1.99,2.958 1.354,0.229 10 true More than 0.037 mA 0.833,2.958 1.906,3.167 1.073,0.208 10 true Below -0.075 mA 2.677,2.865 3.083,3.052 0.406,0.188 10 false OK 5.302,2.844 5.708,3.031 0.406,0.188 10 false OK 3.375,2.344 4.5,2.552 1.125,0.208 10 false Output Current 3.292,2.656 4.833,2.875 1.542,0.219 10 false More than 0.33 mA 3.49,2.938 4.75,3.167 1.26,0.229 10 false Below -0.86 mA 6.385,2.302 6.708,2.51 0.323,0.208 10 false - 0.229,4.365 0.552,4.573 0.323,0.208 10 false 2 5.25,4.906 5.656,5.094 0.406,0.188 10 false OK 2.667,4.833 3.073,5.021 0.406,0.188 10 false NG 0.625,4.823 2.094,5.083 1.469,0.26 10 false Almost no reaction 5.896,3.615 7.094,4.021 1.198,0.406 10 false Air fuel ratio sensor (sensor 1) 5.885,4.198 7.094,4.563 1.208,0.365 10 false Air fuel ratio sensor (sensor 1) heater 5.885,4.833 7.083,5.208 1.198,0.375 10 false Air fuel ratio sensor (sensor 1) circuit 5.802,3.615 6.125,3.823 0.323,0.208 10 false - 5.802,4.198 6.125,4.406 0.323,0.208 10 false - 5.792,4.833 6.115,5.042 0.323,0.208 10 false - 5.26,6.885 5.667,7.073 0.406,0.188 10 false NG 2.688,7 3.094,7.188 0.406,0.188 10 false OK 5.802,5.677 6.135,5.885 0.333,0.208 10 false - 5.792,6.281 6.125,6.49 0.333,0.208 10 false - 5.792,6.885 6.125,7.094 0.333,0.208 10 false - 5.24,8.948 5.646,9.135 0.406,0.188 10 false NG 2.646,8.948 3.052,9.135 0.406,0.188 10 false NG 6.021,7.969 6.99,8.292 0.969,0.323 10 false Fuel system 6.01,8.552 7.052,9.344 1.042,0.792 10 false Gas leak from exhaust system 5.917,7.969 6.25,8.177 0.333,0.208 10 false - 5.906,8.563 6.24,8.771 0.333,0.208 10 false - 3.344,1.385 4.573,1.583 1.229,0.198 10 false Injection Volume 0.677,3.469 1.906,3.667 1.229,0.198 10 false Injection Volume 3.333,3.49 4.563,3.688 1.229,0.198 10 false Injection Volume 0.698,4.354 1.833,4.594 1.135,0.24 10 false Output Current 3.406,4.354 4.531,4.563 1.125,0.208 10 false Output Current 3.313,4.771 4.854,4.99 1.542,0.219 10 false More than 0.33 mA 3.521,5.052 4.781,5.281 1.26,0.229 10 false Below -0.86 mA 3.26,6.865 4.729,7.125 1.469,0.26 10 false Almost no reaction 0.667,5.552 1.896,5.75 1.229,0.198 10 false Injection Volume 3.313,5.542 4.542,5.74 1.229,0.198 10 false Injection Volume 0.708,7.615 1.938,7.813 1.229,0.198 10 false Injection Volume 3.323,7.615 4.552,7.813 1.229,0.198 10 false Injection Volume 0.646,8.917 2.115,9.177 1.469,0.26 10 false Almost no reaction 3.292,8.917 4.76,9.177 1.469,0.26 10 false Almost no reaction 0.729,6.479 1.865,6.719 1.135,0.24 10 false Output Current 0.708,8.542 1.844,8.781 1.135,0.24 10 false Output Current 3.385,6.438 4.51,6.646 1.125,0.208 10 false Output Current 3.406,8.542 4.531,8.75 1.125,0.208 10 false Output Current 5.896,5.667 7.094,6.073 1.198,0.406 10 false Air fuel ratio sensor (sensor 2) 5.875,6.281 7.083,6.646 1.208,0.365 10 false Air fuel ratio sensor (sensor 2) heater 5.875,6.885 7.073,7.26 1.198,0.375 10 false Air fuel ratio sensor (sensor 2) circuit 4.031,1.688 4.583,1.906 0.552,0.219 10 false 12.5% 4,1.906 4.656,2.125 0.656,0.219 10 false -12.5% 1.396,3.771 1.948,3.99 0.552,0.219 10 false 12.5% 1.354,3.969 2.01,4.188 0.656,0.219 10 false -12.5% 4,3.781 4.552,4 0.552,0.219 10 false 12.5% 3.958,3.979 4.615,4.198 0.656,0.219 10 false -12.5% 1.396,5.833 1.948,6.052 0.552,0.219 10 false 12.5% 1.354,6.031 2.01,6.25 0.656,0.219 10 false -12.5% 3.958,5.854 4.51,6.073 0.552,0.219 10 false 12.5% 3.917,6.052 4.573,6.271 0.656,0.219 10 false -12.5% 1.385,7.875 1.938,8.094 0.552,0.219 10 false 12.5% 1.333,8.083 1.99,8.302 0.656,0.219 10 false -12.5% 3.948,7.885 4.5,8.104 0.552,0.219 10 false 12.5% 3.906,8.094 4.563,8.313 0.656,0.219 10 false -12.5% 0.229,6.365 0.552,6.573 0.323,0.208 10 false 3 0.24,8.406 0.563,8.615 0.323,0.208 10 false 4 0.625,6.844 1.969,7.052 1.344,0.208 10 true More than 0.037 mA 0.823,7.083 1.885,7.313 1.063,0.229 10 true Below -0.075 mA

Performing the Active Test "Control the Injection Volume for A/F Sensor" allows the output value of the air fuel ratio sensors (sensor 1 and sensor 2) to be checked and graphed.

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P013616)
a.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
P013616 and other DTCs are output A
P013616 is output B


HINT:

If any DTCs other than P013616 are output, troubleshoot those DTCs first.




A

GO TO DTC CHART

B

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
2.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

Pre-procedure1

a.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.


b.

Warm up the air fuel ratio sensors at an engine speed of 2500 rpm for 90 seconds.


Procedure1

a.

Perform the Control the Injection Volume for A/F Sensor operation with the engine idling.

Powertrain > Engine > Active Test
Active Test Display
Control the Injection Volume for A/F Sensor
Data List Display
Coolant Temperature
Injection Volume
A/F (O2) Sensor Current B1S1
A/F (O2) Sensor Current B1S2
50004 372 8 205,277,230,564

b.

Monitor the output values of the air fuel ratio sensor (sensor 1) and air fuel ratio sensor (sensor 2) (A/F (O2) Sensor Current B1S1 and A/F (O2) Sensor Current B1S2) displayed on the GTS.

HINT:
·

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

The air fuel ratio sensor (sensor 1) has an output delay of a few seconds and the air fuel ratio sensor (sensor 2) has a maximum output delay of approximately 20 seconds.

·

If the sensor output value does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Standard
GTS Display (Sensor) Injection Volume Status Current
A/F (O2) Sensor Current B1S1
(Air fuel ratio (sensor 1))
12.5% Rich Below -0.075 mA
-12.5% Lean Higher than 0.037 mA
A/F (O2) Sensor Current B1S2
(Air fuel ratio (sensor 2))
12.5% Rich Below -0.86 mA
-12.5% Lean Higher than 0.33 mA

Result:
Status of A/F (O2) Sensor Current B1S1 Status of A/F (O2) Sensor Current B1S2 Suspected Trouble Area Proceed to
Lean/Rich Lean/Rich
·

Air fuel ratio sensor (sensor 2)


A
Lean Lean
·

Gas leak from exhaust system

·

EGR valve assembly

·

Extremely lean actual air fuel ratio

·

Air fuel ratio sensor (sensor 2)


B
Rich Rich
·

Gas leak from exhaust system

·

EGR valve assembly

·

Extremely rich actual air fuel ratio

·

Air fuel ratio sensor (sensor 2)


B
Lean/Rich Lean
·

Air fuel ratio sensor (sensor 2)

·

Gas leak from exhaust system


C
Lean/Rich Rich
·

Air fuel ratio sensor (sensor 2)

·

Gas leak from exhaust system


C
Lean Lean/Rich
·

Air fuel ratio sensor (sensor 1)

·

Air fuel ratio sensor (sensor 2)


D
Rich Lean/Rich
·

Air fuel ratio sensor (sensor 1)

·

Air fuel ratio sensor (sensor 2)


D


Lean: During the Control the Injection Volume for A/F Sensor Active Test, the air fuel ratio sensor (sensor 1) output current (A/F (O2) Sensor Current B1S1) is consistently higher than 0.037 mA, and the air fuel ratio sensor (sensor 2) output current (A/F (O2) Sensor Current B1S2) is consistently higher than 0.33 mA.

Rich: During the Control the Injection Volume for A/F Sensor Active Test, the air fuel ratio sensor (sensor 1) output current (A/F (O2) Sensor Current B1S1) is consistently below -0.075 mA, and the air fuel ratio sensor (sensor 2) output current (A/F (O2) Sensor Current B1S2) is consistently below -0.86 mA.

Lean/Rich: During the Control the Injection Volume for A/F Sensor Active Test, the output current of the air fuel ratio sensor (sensor 1) or air fuel ratio sensor (sensor 2) alternate correctly.


HINT:

Refer to "Data List / Active Test" [A/F (O2) Sensor Current B1S1, A/F (O2) Sensor Current B1S2].

Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST



Post-procedure1

a.

None.



A

3.REPLACE AIR FUEL RATIO SENSOR (SENSOR 2)

B

6.CHECK FOR EXHAUST GAS LEAK

C

24.CHECK FOR EXHAUST GAS LEAK

D

25.REPLACE AIR FUEL RATIO SENSOR (SENSOR 2)
3.REPLACE AIR FUEL RATIO SENSOR (SENSOR 2)
HINT:

Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>AIR FUEL RATIO SENSOR (for Sensor 2)>REMOVAL

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (sensor 2).

Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

4.CLEAR DTC
4.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

Pre-procedure1

a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


Procedure1

a.

Perform the All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 20

b.

Input the DTC: P013616.


c.

Check the DTC judgment result.

Result
GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



Result:
Proceed to
NEXT



Post-procedure1

a.

None.



NEXT

END

6.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks in exhaust system.



Result:
Proceed to
OK
NG



OK

7.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)

NG

REPAIR OR REPLACE EXHAUST SYSTEM
HINT:

Perform "Inspection After Repair" after repairing or replacing the exhaust system.

Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



7.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)

Pre-procedure1

a.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher.

HINT:

The A/C switch and all accessories should be off.



Procedure1

a.

Check the engine idling condition and Intake Manifold Absolute Pressure values in the Data List while performing the Active Test.

Powertrain > Engine > Active Test
Active Test Display
Control the EGR Step Position
Data List Display
Engine Speed
Intake Manifold Absolute Pressure
Coolant Temperature
EGR Step Position
50004 372 25 211,385,205,386
NOTICE:
·

Do not leave the EGR valve open for 10 seconds or more during the Active Test.

·

Be sure to return the EGR valve to step 0 when the Active Test is completed.

·

Do not open the EGR valve 30 steps or more during the Active Test.



OK:

The value of Intake Manifold Absolute Pressure and Engine Speed change in response to EGR step position.


Standard:
- Control the EGR Step Position (Active Test)
0 Steps 0 to 30 Steps
Idling condition Steady idling Idling changes from steady to rough idling or engine stalls
Intake Manifold Absolute Pressure
(Data List)
Intake Manifold Absolute Pressure value is 18 to 38 kPa(abs)
(2.6 to 5.5 psi(abs))
(EGR valve is fully closed)
Intake Manifold Absolute Pressure value is at least +10 kPa (1.45 psi) higher than when EGR valve is fully closed


HINT:

During Active Test, if the idling condition does not change in response to EGR step position, then there is probably a malfunction in the EGR valve.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

12.READ VALUE USING GTS (MASS AIR FLOW SENSOR)

NG

8.INSPECT EGR VALVE ASSEMBLY
8.INSPECT EGR VALVE ASSEMBLY

Pre-procedure1

a.

Remove the EGR valve assembly.

HINT:

Click hereEngine / Hybrid System>M15A-FKS (EMISSION CONTROL)>EGR VALVE>REMOVAL



Procedure1

a.

Check if the EGR valve is stuck open.

OK:

EGR valve is tightly closed.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

9.CHECK PCV VALVE AND HOSE CONNECTIONS

NG

REPLACE EGR VALVE ASSEMBLY

Click hereEngine / Hybrid System>M15A-FKS (EMISSION CONTROL)>EGR VALVE>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the EGR valve assembly.

Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



9.CHECK PCV VALVE AND HOSE CONNECTIONS
A471818

a.

Check the PCV hose connections.



OK:

PCV hose and PCV valve are connected correctly and are not damaged.


Result:
Proceed to
OK
NG



OK

10.CHECK INTAKE SYSTEM

NG

REPAIR OR REPLACE PCV VALVE OR HOSE

10.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks.

Click hereEngine / Hybrid System>M15A-FKS (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION

OK:

No leaks in intake system.



Result:
Proceed to
OK
NG



OK

11.READ VALUE USING GTS (COOLANT TEMPERATURE)

NG

REPAIR OR REPLACE INTAKE SYSTEM
HINT:

Perform "Inspection After Repair" after repairing or replacing the intake system.

Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



11.READ VALUE USING GTS (COOLANT TEMPERATURE)
a.

Read the Data List twice, when the engine is both cold and warmed up.

Powertrain > Engine > Data List
Tester Display
Coolant Temperature
50003 372 205
Standard:
GTS Display Condition Specified Condition
Coolant Temperature Cold engine Same as ambient air temperature
Warm engine Between 75 and 100°C (167 and 212°F)



Result:
Proceed to
OK
NG



OK

12.READ VALUE USING GTS (MASS AIR FLOW SENSOR)

NG

REPLACE ENGINE COOLANT TEMPERATURE SENSOR

Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>ENGINE COOLANT TEMPERATURE SENSOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.

Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



12.READ VALUE USING GTS (MASS AIR FLOW SENSOR)

Pre-procedure1

a.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher with all the accessories switched off and shift position N.


Procedure1

a.

Read Mass Air Flow Sensor while maintaining an engine speed of 3000 rpm.

Powertrain > Engine > Data List
Tester Display
Engine Speed
Mass Air Flow Sensor
Coolant Temperature
50003 372 211,215,205
Result:
Result Proceed to
The value of Mass air Flow Sensor is between 4.0 gm/sec and 8.0 gm/sec A
None of the above conditions are met B



Post-procedure1

a.

None.



A

13.CHECK FUEL PRESSURE (FOR LOW PRESSURE SIDE)

B

17.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY CONNECTOR CONNECTION)
13.CHECK FUEL PRESSURE (FOR LOW PRESSURE SIDE)
a.

Check the fuel pressure (for low pressure side).

Click hereEngine / Hybrid System>M15A-FKS (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

14.CHECK FUEL PRESSURE (FOR HIGH PRESSURE SIDE)

NG

28.CHECK FUEL LINE
14.CHECK FUEL PRESSURE (FOR HIGH PRESSURE SIDE)
a.

Check the fuel pressure (for high pressure side).

Click hereEngine / Hybrid System>M15A-FKS (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

15.INSPECT IGNITION SYSTEM

NG

28.CHECK FUEL LINE
15.INSPECT IGNITION SYSTEM

OK

16.INSPECT FUEL INJECTOR ASSEMBLY

NG

REPAIR OR REPLACE IGNITION SYSTEM
HINT:

Perform "Inspection After Repair" after replacing the ignition system.

Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



16.INSPECT FUEL INJECTOR ASSEMBLY
a.

Check the injection volume (whether fuel volume is high or low, and whether injection pattern is poor).

Click hereEngine / Hybrid System>M15A-FKS (FUEL)>FUEL INJECTOR>INSPECTION


Result:
Proceed to
OK
NG



OK

17.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY CONNECTOR CONNECTION)

NG

REPLACE FUEL INJECTOR ASSEMBLY

Click hereEngine / Hybrid System>M15A-FKS (FUEL)>FUEL INJECTOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the fuel injector assembly.

Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



17.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY CONNECTOR CONNECTION)
a.

Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter sub-assembly and ECM.

HINT:

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE

Repair any problems.



Result:
Proceed to
NEXT



NEXT

18.CLEAR DTC
18.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

19.CHECK WHETHER DTC OUTPUT RECURS (P013616)
19.CHECK WHETHER DTC OUTPUT RECURS (P013616)

Pre-procedure1

a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


Procedure1

a.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
P013616 is output B



Post-procedure1

a.

None.



A

END

B

20.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
20.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)

Pre-procedure1

a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the ECM connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D23,D51)Location & Routing

Click Connector(D23)Engine Compartment>Engine Wire>Intake Mass Air Flow Meter Sub-Assembly

Click Connector(D51)Engine Compartment>Engine Wire>ECM

D23-4 (VCC) - D51-78 (VCVG) Always Below 1 Ω
D23-3 (FG) - D51-101 (VG) Always Below 1 Ω
D23-2 (E2G) - D51-79 (E2G) Always Below 1 Ω
D23-4 (VCC) or D51-78 (VCVG) - Body ground and other terminals Always 10 kΩ or higher
D23-3 (FG) or D51-101 (VG) - Body ground and other terminals Always 10 kΩ or higher
D23-2 (E2G) or D51-79 (E2G) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

21.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY
HINT:
·

If the result of the inspection performed in steps 12 (READ VALUE USING GTS (MASS AIR FLOW SENSOR)) indicated no problem, proceed to the next step without replacing the mass air flow meter sub-assembly.

·

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



a.

Replace the mass air flow meter sub-assembly.


Result:
Proceed to
NEXT



NEXT

22.CLEAR DTC
22.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

23.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
23.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

Pre-procedure1

a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


Procedure1

a.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
P013616 is output B



Post-procedure1

a.

None.



A

END

B

24.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks in exhaust system.


HINT:
·

Perform "Inspection After Repair" after repairing or replacing the exhaust system.

Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION

·

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (sensor 2).

Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION




Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE EXHAUST SYSTEM

25.REPLACE AIR FUEL RATIO SENSOR (SENSOR 2)
HINT:

Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>AIR FUEL RATIO SENSOR (for Sensor 1)>REMOVAL

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (sensor 1).

Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

26.CLEAR DTC
26.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

27.CHECK WHETHER DTC OUTPUT RECURS (DTC P013616)
27.CHECK WHETHER DTC OUTPUT RECURS (DTC P013616)

Pre-procedure1

a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


Procedure1

a.

Perform the All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 20

b.

Input the DTC: P013616.


c.

Check that the DTC judgment result is NORMAL. If the DTC judgment result is INCOMPLETE, perform the confirmation drive pattern again but increase the vehicle speed.

Result:
Result Proceed to
NORMAL
(DTCs are not output)
A
ABNORMAL
(DTC P013616 is output)
B



Post-procedure1

a.

None.



A

END

B

REPLACE AIR FUEL RATIO SENSOR (SENSOR 2)

Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>AIR FUEL RATIO SENSOR (for Sensor 2)>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (sensor 2).

Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



28.CHECK FUEL LINE
a.

Check the fuel lines for leaks or blockage.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE FUEL SYSTEM