The ECM uses air fuel ratio sensors mounted in front of and behind the Three-Way Catalytic Converter (TWC) to monitor its efficiency.
The first sensor, the air fuel ratio sensor (sensor 1), sends pre-catalyst information to the ECM. The second sensor, the air fuel ratio sensor (sensor 2), sends post-catalyst information to the ECM.
In order to detect any deterioration in the three-way catalytic converter, the ECM calculates the oxygen storage capacity of the three-way catalytic converter. This calculation is based on the output current of the air fuel ratio sensor (sensor 2) while performing active air fuel ratio control.
The oxygen storage capacity value is an indication of the oxygen storage capacity of the three-way catalytic converter. When the vehicle is being driven with a warm engine, active air fuel ratio control is performed for approximately 30 seconds. When it is performed, the ECM deliberately sets the air fuel ratio to lean or rich levels. If the cycle of the waveform for the air fuel ratio sensor (sensor 2) is long, the oxygen storage capacity is great. There is a direct correlation between the air fuel ratio sensor (sensor 2) and the oxygen storage capacity of the three-way catalytic converter.
The ECM uses the oxygen storage capacity value to determine the state of the three-way catalytic converter. If any deterioration has occurred, the ECM will illuminate the MIL and store a DTC.
This system determines the deterioration of the entire catalyst system (including the front and rear catalysts), by using the oxygen storage capacity value of the front catalyst, that is more sensitive than the rear catalyst, as the representative value. Therefore, be sure to replace the front and rear catalysts together when catalyst replacement is necessary.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | DTC Output from | Priority | Note |
|---|---|---|---|---|---|---|---|
| P042000 | Catalyst System Efficiency Below Threshold Bank 1 | The oxygen storage capacity value is less than the standard value under active air fuel ratio control (1 trip detection logic). | ·
Gas leak from exhaust system ·
Air fuel ratio sensor (sensor 1) ·
Air fuel ratio sensor (sensor 2) ·
Exhaust manifold (TWC: Front catalyst) ·
Front exhaust pipe assembly (TWC: Rear catalyst) ·
EGR valve assembly |
Comes on | Engine | B | SAE: P0420 |
| *1 | Exhaust Manifold (TWC: Front Catalyst) | *2 | Front Exhaust Pipe Assembly (TWC: Rear Catalyst) |
| *3 | Tail Exhaust Pipe Assembly | *4 | Air Fuel Ratio Sensor (Sensor 1) |
| *5 | Air Fuel Ratio Sensor (Sensor 2) | - | - |
When replacing the exhaust manifold (*1) and the front exhaust pipe assembly (*2) in order to replace the three-way catalytic converter, it is not necessary to replace the air fuel ratio sensor (sensor 1) (*4) and the air fuel ratio sensor (sensor 2) (*5).
| Required Sensors/Components (Main) | Air fuel ratio sensor (sensor 1)
Air fuel ratio sensor (sensor 2) |
| Required Sensors/Components (Related) | Intake air temperature sensor
Mass air flow meter sub-assembly Crankshaft position sensor Engine coolant temperature sensor |
| Frequency of Operation | Once per driving cycle |
| Battery voltage | 11 V or higher |
| Intake air temperature | -10°C (14°F) or higher |
| Engine coolant temperature | 75°C (167°F) or higher |
| Atmospheric pressure | 76 kPa(abs) [11 psi(abs)] or higher |
| Idling | Off |
| Engine speed | Less than 3200 rpm |
| Air fuel ratio sensor (sensor 1) status | Activated |
| Fuel system status | Closed loop |
| Engine load | 10% or higher, and less than 100% |
| All of the following conditions are met | 1, 2 and 3 |
| 1. Mass air flow | 6 gm/sec or more, and less than 75 gm/sec |
| 2. Front catalyst temperature (estimated) | 580°C (1076°F) or higher, and below 800°C (1472°F) |
| 3. Rear catalyst temperature (estimated) | 480°C (896°F) or higher, and below 700°C (1292°F) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher with the shift lever in P or neutral [A].
In order to keep the idle stable, turn the A/C and all other electric loads off and do not perform any shift operations.
Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [B].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Drive the vehicle while keeping the engine load as constant as possible.
Turn the ignition switch off and wait for at least 30 seconds [C].
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [D].
Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [E].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Drive the vehicle while keeping the engine load as constant as possible.
Enter the following menus: Powertrain / Engine / Trouble Codes [F].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P042000.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
If the judgment result is NORMAL, the system is normal.
If the judgment result is ABNORMAL, the system has a malfunction.
If the judgment result is INCOMPLETE, perform the following procedure.
Drive the vehicle at a speed between 75 and 100 km/h (47 and 62 mph) for 10 minutes or more [G].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Drive the vehicle while keeping the engine load as constant as possible.
Enter the following menus: Powertrain / Engine / Trouble Codes [H].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P042000.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
If the judgment result is NORMAL, the system is normal.
If the judgment result is ABNORMAL, the system is malfunctioning.
If a malfunction cannot be found when troubleshooting DTC P042000, a lean or rich abnormality may be the cause. Perform troubleshooting by following the inspection procedure for P017100 (System Too Lean) and P017200 (System Too Rich).
Sensor 1 refers to the sensor closest to the engine assembly.
Sensor 2 refers to the sensor farthest away from the engine assembly.
Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Read the DTCs.
| Result | Proceed to |
|---|---|
| P042000 and other DTCs are output | A |
| P042000 is output | B |
If any DTCs other than P042000 are output, troubleshoot those DTCs first.
A
B
Pre-procedure1
Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher.
Warm up the air fuel ratio sensors at an engine speed of 2500 rpm for 90 seconds.
Procedure1
Change the fuel injection volume using the GTS, and monitor the output current of the air fuel ratio sensor (sensor 1) (A/F (O2) Sensor Current B1S1) and air fuel ratio sensor (sensor 2) (A/F (O2) Sensor Current B1S2) displayed on the GTS.
| Active Test Display |
|---|
| Control the Injection Volume for A/F Sensor |
| Data List Display |
|---|
| Coolant Temperature |
| Injection Volume |
| A/F (O2) Sensor Current B1S1 |
| A/F (O2) Sensor Current B1S2 |
The Active Test "Control the Injection Volume for A/F Sensor" can be used to lower the fuel injection volume by 12.5% or increase the injection volume by 12.5%.
The air fuel ratio sensor (sensor 1) is displayed as A/F (O2) Sensor Current B1S1, and the air fuel ratio sensor (sensor 2) is displayed as A/F (O2) Sensor Current B1S2 on the GTS.
The air fuel ratio sensor (sensor 1) has an output delay of a few seconds and the air fuel ratio sensor (sensor 2) has a maximum output delay of approximately 20 seconds.
If the sensor output current does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.
| GTS Display
(Sensor) |
Injection Volume | Status | Current |
|---|---|---|---|
| A/F (O2) Sensor Current B1S1
(Air fuel ratio (sensor 1)) |
12.5% | Rich | Below -0.075 mA |
| -12.5% | Lean | Higher than 0.037 mA | |
| A/F (O2) Sensor Current B1S2
(Air fuel ratio (sensor 2)) |
12.5% | Rich | Below -0.86 mA |
| -12.5% | Lean | Higher than 0.33 mA |
| Status A/F (O2) Sensor Current B1S1 | Status A/F (O2) Sensor Current B1S2 | Actual air fuel ratio, air fuel ratio sensor (sensor 1) and air fuel ratio sensor (sensor 2) condition | Main Suspected Trouble Area | Proceed to |
|---|---|---|---|---|
| Lean/Rich | Lean/Rich | Normal | ·
Three-way catalytic converter ·
Gas leak from exhaust system ·
EGR valve assembly |
A |
| Lean | Lean/Rich | Air fuel ratio sensor (sensor 1) malfunction | ·
Air fuel ratio sensor (sensor 1) |
B |
| Rich | Lean/Rich | Air fuel ratio sensor (sensor 1) malfunction | ·
Air fuel ratio sensor (sensor 1) |
B |
| Lean/Rich | Lean | Air fuel ratio sensor (sensor 2) malfunction | ·
Air fuel ratio sensor (sensor 2) ·
Gas leak from exhaust system |
C |
| Lean/Rich | Rich | Air fuel ratio sensor (sensor 2) malfunction | ·
Air fuel ratio sensor (sensor 2) ·
Gas leak from exhaust system |
C |
| Lean | Lean | Actual air fuel ratio lean | ·
Extremely lean actual air fuel ratio ·
Gas leak from exhaust system ·
EGR valve assembly |
D |
| Rich | Rich | Actual air fuel ratio rich | ·
Extremely rich actual air fuel ratio ·
Gas leak from exhaust system ·
EGR valve assembly |
D |
Lean: During the Control the Injection Volume for A/F Sensor Active Test, the air fuel ratio sensor (sensor 1) output current (A/F (O2) Sensor Current B1S1) is consistently higher than 0.037 mA, and the air fuel ratio sensor (sensor 2) output current (A/F (O2) Sensor Current B1S2) is consistently higher than 0.33 mA.
Rich: During the Control the Injection Volume for A/F Sensor Active Test, the air fuel ratio sensor (sensor 1) output current (A/F (O2) Sensor Current B1S1) is consistently below -0.075 mA, and the air fuel ratio sensor (sensor 2) output current (A/F (O2) Sensor Current B1S2) is consistently below -0.86 mA.
Lean/Rich: During the Control the Injection Volume for A/F Sensor Active Test, the output current of the air fuel ratio sensor (sensor 1) or air fuel ratio sensor (sensor 2) alternate correctly.
Refer to "Data List / Active Test" [A/F (O2) Sensor Current B1S1, A/F (O2) Sensor Current B1S2].
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST
Post-procedure1
None.
A
B
C
D
Check for exhaust gas leaks.
No gas leaks in exhaust system.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher.
The A/C switch and all accessories should be off.
Procedure1
Check the engine idling condition and Intake Manifold Absolute Pressure values in the Data List while performing the Active Test.
| Active Test Display |
|---|
| Control the EGR Step Position |
| Data List Display |
|---|
| Engine Speed |
| Intake Manifold Absolute Pressure |
| Coolant Temperature |
| EGR Step Position |
Do not leave the EGR valve open for 10 seconds or more during the Active Test.
Be sure to return the EGR valve to step 0 when the Active Test is completed.
Do not open the EGR valve 30 steps or more during the Active Test.
The value of Intake Manifold Absolute Pressure and Engine Speed change in response to EGR step position.
| - | Control the EGR Step Position (Active Test) | |
|---|---|---|
| 0 Steps | 0 to 30 Steps | |
| Idling condition | Steady idling | Idling changes from steady to rough idling or engine stalls |
| Intake Manifold Absolute Pressure
(Data List) |
Intake Manifold Absolute Pressure value is 18 to 38 kPa(abs)
(2.6 to 5.5 psi(abs)) (EGR valve is fully closed) |
Intake Manifold Absolute Pressure value is at least +10 kPa (1.45 psi) higher than when EGR valve is fully closed |
During Active Test, if the idling condition does not change in response to EGR step position, then there is probably a malfunction in the EGR valve.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None.
OK
NG
Pre-procedure1
Remove the EGR valve assembly.
Procedure1
Check if the EGR valve is stuck open.
EGR valve is tightly closed.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None.
OK
NG
Click hereEngine / Hybrid System>M15A-FKS (EMISSION CONTROL)>EGR VALVE>REMOVAL
Perform "Inspection After Repair" after replacing the EGR valve assembly.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>AIR FUEL RATIO SENSOR (for Sensor 1)>REMOVAL
Perform "Inspection After Repair" after replacing the air fuel ratio sensor (sensor 1).
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Check for exhaust gas leaks.
No gas leaks in exhaust system.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>AIR FUEL RATIO SENSOR (for Sensor 2)>REMOVAL
Perform "Inspection After Repair" after replacing the air fuel ratio sensor (sensor 2).
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Check for exhaust gas leaks.
No gas leaks in exhaust system.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher.
The A/C switch and all accessories should be off.
Procedure1
Check the engine idling condition and Intake Manifold Absolute Pressure values in the Data List while performing the Active Test.
| Active Test Display |
|---|
| Control the EGR Step Position |
| Data List Display |
|---|
| Engine Speed |
| Intake Manifold Absolute Pressure |
| Coolant Temperature |
| EGR Step Position |
Do not leave the EGR valve open for 10 seconds or more during the Active Test.
Be sure to return the EGR valve to step 0 when the Active Test is completed.
Do not open the EGR valve 30 steps or more during the Active Test.
The value of Intake Manifold Absolute Pressure and Engine Speed change in response to EGR step position.
| - | Control the EGR Step Position (Active Test) | |
|---|---|---|
| 0 Steps | 0 to 30 Steps | |
| Idling condition | Steady idling | Idling changes from steady to rough idling or engine stalls |
| Intake Manifold Absolute Pressure
(Data List) |
Intake Manifold Absolute Pressure value is 18 to 38 kPa(abs)
(2.6 to 5.5 psi(abs)) (EGR valve is fully closed) |
Intake Manifold Absolute Pressure value is at least +10 kPa (1.45 psi) higher than when EGR valve is fully closed |
During Active Test, if the idling condition does not change in response to EGR step position, then there is probably a malfunction in the EGR valve.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None.
OK
NG
Pre-procedure1
Remove the EGR valve assembly.
Procedure1
Check if the EGR valve is stuck open.
EGR valve is tightly closed.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None.
OK
NG
Click hereEngine / Hybrid System>M15A-FKS (EMISSION CONTROL)>EGR VALVE>REMOVAL
Perform "Inspection After Repair" after replacing the EGR valve assembly.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
Check the PCV hose connections.
Check the PCV valve.
Click hereEngine / Hybrid System>M15A-FKS (EMISSION CONTROL)>PCV VALVE>INSPECTION
PCV hose and PCV valve are connected correctly and are not damaged.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the intake system for vacuum leaks.
Click hereEngine / Hybrid System>M15A-FKS (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION
No leaks in intake system.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Perform "Inspection After Repair" after repairing or replacing the intake system.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
Read the Data List twice, when the engine is both cold and warmed up.
| Tester Display |
|---|
| Coolant Temperature |
| GTS Display | Condition | Specified Condition |
|---|---|---|
| Coolant Temperature | Cold engine | Same as ambient air temperature |
| Warm engine | Between 75 and 100°C (167 and 212°F) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>ENGINE COOLANT TEMPERATURE SENSOR>REMOVAL
Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
Pre-procedure1
Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher with all the accessories switched off and shift position N.
Procedure1
Read the Mass Air Flow Sensor while maintaining an engine speed of 3000 rpm.
| Tester Display |
|---|
| Engine Speed |
| Mass Air Flow Sensor |
| Coolant Temperature |
During charge control, the engine speed is set at idle. Therefore, the engine speed will not increase when the accelerator pedal is depressed. In this case, read the Data List after charge control has completed.
| Result | Proceed to |
|---|---|
| The value of Mass Air Flow Sensor is between 4.0 gm/sec and 8.0 gm/sec | A |
| None of the above conditions are met | B |
Post-procedure1
None.
A
B
Click hereEngine / Hybrid System>M15A-FKS (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>M15A-FKS (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION
If the spark plugs or ignition system malfunctions, engine misfire may occur. The misfire count can be read using the GTS. Enter the following menus: Powertrain / Engine / Data List / Misfire Count Cylinder #1 to Misfire Count Cylinder #3.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Perform "Inspection After Repair" after repairing or replacing the ignition system.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
Check the injection and volume.
Refer to the fuel injector assembly inspection procedure.
Click hereEngine / Hybrid System>M15A-FKS (FUEL)>FUEL INJECTOR>INSPECTION
If the fuel injector assemblies malfunction, engine misfire may occur. The misfire count can be read using the GTS. Enter the following menus: Powertrain / Engine / Data List / Misfire Count Cylinder #1 to Misfire Count Cylinder #3.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>M15A-FKS (FUEL)>FUEL INJECTOR>REMOVAL
Perform "Inspection After Repair" after replacing the fuel injector assembly.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter and ECM.
Repair any problems.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
None.
Procedure1
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
Post-procedure1
Turn the ignition switch off and wait for at least 30 seconds.
NEXT
Pre-procedure1
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Procedure1
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| P042000 is output | B |
Post-procedure1
None.
A
B
Pre-procedure1
Disconnect the mass air flow meter connector.
Disconnect the ECM connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(D23,D51)Location & Routingewd_type=routing;type=c,c;code=D23,D51 Click Connector(D23)Engine Compartment>Engine Wire>Intake Mass Air Flow Meter Sub-Assemblyewd_type=component;type=c;code=D23;pinno=4,3,2 Click Connector(D51)Engine Compartment>Engine Wire>ECMewd_type=component;type=c;code=D51;pinno=78,101,79 |
||
| D23-4 (VCC) - D51-78 (VCVG) | Always | Below 1 Ω |
| D23-3 (FG) - D51-101 (VG) | Always | Below 1 Ω |
| D23-2 (E2G) - D51-79 (E2G) | Always | Below 1 Ω |
| D23-4 (VCC) or D51-78 (VCVG) - Body ground and other terminals | Always | 10 kΩ or higher |
| D23-3 (FG) or D51-101 (VG) - Body ground and other terminals | Always | 10 kΩ or higher |
| D23-2 (E2G) or D51-79 (E2G) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None.
OK
NG
If the result of the inspection performed in steps 15 (READ VALUE USING GTS (MASS AIR FLOW SENSOR)) indicated no problem, proceed to the next step without replacing the mass air flow meter.
Perform "Inspection After Repair" after replacing the mass air flow meter.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
None.
Procedure1
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
Post-procedure1
Turn the ignition switch off and wait for at least 30 seconds.
NEXT
Pre-procedure1
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Procedure1
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| P042000 is output | B |
Post-procedure1
None.
A
B
Check the fuel lines for leaks or blockage.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>Fuel Pump Control Circuit
Perform "Inspection After Repair" after replacing the fuel pump.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
NG
Perform "Inspection After Repair" after repairing or replacing the exhaust system.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
None.
Procedure1
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
Post-procedure1
Turn the ignition switch off and wait for at least 30 seconds.
NEXT
Pre-procedure1
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Procedure1
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| P042000 is output | B |
Post-procedure1
None.
A
B
When replacing the exhaust manifold and the front exhaust pipe assembly in order to replace the three-way catalytic converter, it is not necessary to replace the air fuel ratio sensor (sensor 1) and the air fuel ratio sensor (sensor 2).
Confirm the replacement parts, referring to the illustration in the Catalyst Location.
Replace the exhaust manifold (TWC: Front catalyst).
Replace the front exhaust pipe assembly (TWC: Rear catalyst).
| Proceed to |
|---|
| NEXT |
NEXT